MB QUART NSB6V1 Series Nautic Soundbars Installation Guide

June 4, 2024
MB QUART

MB QUART Logo Quick Start
Installation Guide
MB QUART NSB6V1 Series Nautic Soundbars
Nautic
NSB6V1 / NSB10V1
Soundbars

NSB6V1 Series Nautic Soundbars

Congratulations on your choice of MB Quart Nautic Sound
Bars. This “Quick Start” Installation guide is meant to help you complete a basic installation. For more detailed information about the product, please visit our website at MBQuart.com
Wiring
The wiring and connections should be secure and away from any moving parts or extremely hot surfaces.
MB QUART NSB6V1 Series Nautic Soundbars - Fig

Controls

  1. Power – Will turn the unit on or off / Five-second hold/ quick push will switch inputs.
  2. Track BACKWARDS – Press to restart the current track or to back up to previous tracks.
  3. Volume UP – Each press will increase the volume.
  4. Volume DOWN – Each press will decrease the volume.
  5. Track FORWARD – Press to advance to the next track.
  6. Map Light / Illumination – Turn on Map Light, and cycle through illumination settings.
  7. PLAY / PAUSE – Press once to pause. Press again to play.

MB QUART NSB6V1 Series Nautic Soundbars -Controls

Bluetooth Device Pairing

The pairing process can vary based on your particular device. Refer to the operating instructions of your device. Below is the general process to connect. During unit power-up,  the blue LED on the bottom of the control panel will blink indicating that it is in Bluetooth search mode.
During this process “MB Quart” should show up in your list of Bluetooth devices when the search has connected with your device. When the connection is made the blue LED
will change to a solid color.
Once a device has been paired, the unit will reconnect at power up to that device when in range.
When a phone call is received, the audio signal will mute but not disconnect.
To switch to 3.5mm press the power button quickly.
To switch back to BT press the power button again quickly.
MBQuart.com
#MUSIC DEFINED

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date f purchase.
Maxxsonics USA Inc. will, at its discretion, repair or replace defective products during the warranty period. Components that prove to be defective in materials and  workmanship under proper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The costs associated with removal, re-installation, and freight are not the responsibility of Maxxsonic’s consequential damages connected therewith. To view the full warranty, please visit the website.
MB Quart products are designed and engineered in the USA by

MB QUART Logo 2
www.maxxsonics.com
MBQ NAUTIC SBAR QSG 01 – rev1MB QUART Logo

SOUND BAR MOUNTING
The following is intended to help you mount the soundbar. We highly recommend employing the expertise of a professional installer.
The sound bar has two convenient installation styles. Roll Cage and Surface Mount review this document to determine which you will use, then prepare for installation.
A. Prepare a flat work surface to prepare for installation
B. Recruit an assistant to help with lifting Sound Bar into place
C. Use lightweight painters tape to cover your roll cage while you are positioning
INCLUDED PARTS

NUMBER DESCRIPTION QUANTITY INCLUDED
1 Top Tube Clamp (1.5, 1.75 or 2-inch options) 6
2 Channel Slide Lug 2
3 Tube Clamp Base 2
4 & 5 M5X10 Screws (Top & Bottom Clamps)
(Clamp Bottom to Channel Slide Lug) 12
6 Surface Mount Bracket 2
7 M5X20 Screws for “L”
Brackets 2

For additional information on this and other MBQuart products, please check the SUPPORT section of our website https://mbquart.com/support MB QUART NSB6V1 Series Nautic Soundbars - Fig
1

INSTALL STEPS – Surface Mount (L Brackets)
Reference the illustration FIG 1-1 to confirm which components are needed for each STEP.
Items on the list are called out with brackets [X].
STEP 1 – Mount 1 Surface Mount Bracket [6] per side with the longer [7] M5x20 screws.
STEP 2 – Position the Sound Bar in place. Use a marker to identify where the mounting holes will be located on your vehicle. Use at least 2 of the 3 holes to mount the soundbar. Confirm there are no moving parts or wires on the other side of your mounting surface. Consider drilling a small pilot hole.
STEP 3 – Mount the Sound Bar*

  • These mounting screws are not included as different off-road or marine applications will vary.
    For additional information on this and other MBQuart products, please check the SUPPORT section of our website https://mbquart.com/support
    INSTALL STEPS – Roll Cage
    Reference the illustration FIG 1-1 to confirm which components are needed for each STEP.
    Items on the list are called out with brackets [X].
    STEP 1 – Choose the appropriate Top Tube Clamp [1] for your roll cage diameter. We have included 1.5, 1.75, and 2-inch clamps.
    STEP 2 – Insert 2 slide lugs [2] into the mounting channel on top of the soundbar. You want these lugs to be left and right in the channel.
    NOTE – Use some lightweight painter’s tape to mark where you will want the clamping system on the left-right side of your roll cage. The following assembly should remain loose until you know you have the correct position. Only use hand tools do not over-tighten.
    STEP 3 – Mount the Tube Clamp Base [3] to the Channel Slide Lug [2] using two [4/5] M5X10 screws. Make sure to prep both the left and right sides of the soundbar. Position the hooked edge of the Clamp Base to the back of the sound bar – screw holes to the front.
    STEP 4 – With your assistant lifting the sound bar into position, you will confirm that the wires on the sound bar are not pinched and remain accessible on both ends.
    STEP 5 – With the sound bar still held in the air by your helper, you will use the Top Tube Clamp to lock on the back of the Tube Clamp Base and use two [4/5] M5X10 screws per side (left/right) to mount the sound bar `the roll cage.
    NOTE – Use hand tools to secure these screws to avoid damage to the sound bar or the vehicle.
    Do not fully tighten the screws until you are confident of your positioning.
    STEP 5 – Once your positioning is confirmed, use your hand tools to fully tighten the screws on the clamp. Your clamping system should not move left/right. If it is loose, you need to tighten the screws shown in STEP 2.
    NOTE – Once the Soundbar is in the final position, remove any painter’s tape that is visible
    STEP 6 – Wire up the sound bar

ADDITIONAL MOUNTING OPTIONS

If you find that your installation is more exotic or challenging that can be addressed with the included hardware we recommend our build partner AXIA ALLOYS. They offer a wide variety of billet aluminum mount mounting systems for more accessories that you can possibly install on your vehicle. MB QUART
NSB6V1 Series Nautic Soundbars -AXIA ALLOYS

Here is a link to the components for your sound bar. Make sure to check out all the other mounting creativity from AXIA ALLOYS while you’re on the site.
DIMENSIONS & WEIGHT

MODEL LENGTH DEPTH HEIGHT WEIGHT
6 Speakers 21.02 4.92 4.33 12.9 lbs (5.9 kg)
10 Speakers 34.41 4.92 4.33 21 lbs (9.5 kg)

For additional information on this and other MBQuart products,
please check the SUPPORT section of our website
https://mbquart.com/support

Documents / Resources

| MB QUART NSB6V1 Series Nautic Soundbars [pdf] Installation Guide
NSB6V1, NSB10V1, NSB6V1 Series Nautic Soundbars, NSB6V1 Series, Nautic Soundbars, Soundbars
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MB QUART User Manuals

Related Manuals