MB Quart RA1-150.2 150 Watt Amplifier Installation Guide
- June 4, 2024
- MB QUART
Table of Contents
MB Quart RA1-150.2 150 Watt Amplifier Installation Guide
Before you start
⚠ CAUTION ⚠
Many new and factory radios require a reset code when disconnected from
battery power. This is an anti-theft feature . Before unplugging power, you
must determine if your radio/source unit requires a reset code . Check the
operation
manual for your vehicle or contact the dealer.
Congratulations on your choice of a MBQuart amplifier. This “Quick Start Installation” guide is meant to help you “hook up” and play music. For more detailed information , on system setting , speaker and subwoofer configuration and full specifications by model please visit our website at www.MBQuart.com
Power cable size
It is critical to use the proper power and ground cable. Select the size
listed here for your amplifier model. Always use high quality copper cable.
Power cable size and fuse size based on a 17ft power (B+) (OFC) cable length
and 18-inch ground (OFC) oxygen free cable.
Any other lengths used please consult a certified professional installer.
Installation
Common System Setup
Setup
Open Control Panel
To gain access to the RA1 amplifier series top mount setting control panel carefully remove the four screws and lift the face plate up.
When you’re finished with the control panel mindfully put the face plate back together with the four screws. Make sure not to over tighten.
Settings
The illustrations below describe the various controls. Refer to the
illustration that matches your amplifier.
-
LEVEL Adjustment
The level control purpose is to match the output of your source signal to the amplifier. Refer to the section C for detailed instructions. -
X-OVER Switch
This switch will set the amplifier to have a full frequency output or to filter out high or low frequencies. -
Frequencies Adjustment
The Low Pass Filter will cut off the frequencies above the setting. The High Pass Filter will cut off the frequencies below the setting. -
SUBSONIC Switch
The Subsonic Switch will cut off the frequencies below the setting. -
BASS BOOST ⚠
The Bass EQ control will increase the power output at 45Hz for more pronounced bass. Exercise caution when using this control. Increase the level in small
amounts until distortion is noticed , then back off a little.
Level Setting ⚠
This is a critical step to insure your amplifier is properly adjusted to match
the signal output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
- If possible, with the source unit off, confirm that the primary volume control is turned down (counter clockwise).
- Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is turned down. Make sure the source unit controls; balance, fader, bass and treble are all set to center or “O” adjustment. Make sure that the green LED on the end of the amplifier is illuminated.
- Play a clean musical selection of which you are very familiar. CD is preferred. Do not use radio signals for level setting. Hit play and start turning the volume of the source unit up.
- Stop increasing the source unit volume when you reach 3/4 (about 75%) or until you hear speakers begin to slightly start producing distortion.
- Increase the amplifier gain (clockwise) until distortion is heard, then back the level down (counter clockwise) until the distortion is eliminated. Small adjustments may need to be made to balance the levels of multiple amplifiers.
Remote Level Control
Some models include a bass remote. Avoid adjusting the bass remote while operating vehicle.
Turn on Mode
REM turn on SIGNAL SENSE ON, High level
Turn on Mode input DC turn on
REM TURN ON/ DC SENSE ON SWITCH
There are two methods of switching the amplifier on and off. Select the
appropriate position suited for your application.
REM TURN ON
This will turn on the amplifier when a + 12v switched power typically from a
source unit, is connected to the Amp Turn on – BLUE wire on the main power
connection harness.
DC SENSE
The DC SENSE is for use with the source units that do not offer RCA outputs.
⚠ NOTE – If the RCA’s are plugged into the amplifier and the TURN ON MODE is in the DC ON position, the amplifier will NOT turn on. Please re-read this document or hire a professional installer.
MUSICDEFINED
WARRANTY Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty period. Components that prove to be defective in material sand workmanship underproper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned . The costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith . To view the full warranty, please visit the website.
MBQuart products are designed and engineered in the USA by MAXXSONICS
Reference RAl-710.S
700 Watt 5-Channel Amplifier
English Spanish French
Model
l-Ohm
2-Ohm
4-Ohm
RAl-710.5
l x 350w Ch5 Only
4 x 100w + l x 150 Ch5
4 x S0w + l x 150 ChS
10-35kHz Chl-4
10-250Hz Ch5
Signal to Noise Ratio l0ldB
THO% .07%
Variable Hi-Pass 50-250Hz
Variable Subsonic Filter 25Hz Fixed
Bass Boost 0-12dB
Specifications Subject To Change Without Notice
Documents / Resources
| MB
Quart RA1-150.2 150 Watt
Amplifier
[pdf] Installation Guide
RA1-150.2 150 Watt Amplifier, RA1-150.2, 150 Watt Amplifier, Amplifier,
RAl-280.4, RAl-300.1, RAl-750.1, RAl-710.5
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>