MB QUART MBQG-SUB-1 Polaris GENERAL Specific Subwoofer Tuned System Instruction Manual

June 3, 2024
MB QUART

MB QUART MBQG-SUB-1 Polaris GENERAL Specific LOGO

MB QUART MBQG-SUB-1 Polaris GENERAL Specific Subwoofer Tuned System

MB QUART MBQG-SUB-1 Polaris GENERAL Specific
PRODUCT

Installation Instructions

Model: Polaris General
Description: Subwoofer Install
Part Number: MBQG-SUB-1
Assembly Time: 90 Min (1.5-Hours)

Before you begin, read through these instructions and check that all parts are present. Always disconnect negative battery terminal prior to installation. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation.

| Parts List|
---|---|---
No.| Component Name| Qty
1| 10” Subwoofer w/Enclosure (MBQG-SUB-1)| 1
Tools Required

1| Bojo Tool
2| Panel Clip Pliers
3| 10mm & 13mm Socket
4| Rachet
5| 7mm & 13mm Wrench
6| T25 and T40 Torx Driver
7| 11/32” Drill Bit
8| Drill
9| Phillips Screwdriver
10| 4mm & 5mm Allen Wrench

Dash Disassembly

  • Remove hood by turning two latchesMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 1

  • Remove seven push clips from front of dashMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 2

  • Remove top two push pins from driver and passenger door openingMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 3

  • Lift front of dash at eight locations with Bojo toolMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 4MB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 5

  • Remove if your machine has upper pocketMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 6

  • Remove lower switch locations (If your vehicle has switches installed note connections and disconnect)MB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 7

  • Disconnect wires from back of 12 volt accessory portMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 8

  • ● Remove plastic nut from ignition switch and remove from dashMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 9

  • Lower the steering column and disconnect wiring from the back of the instrument cluster and emove the two 10mm bolts to remove the instrument clusterMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 10

  • Disconnect the connectors from the back of the light and four wheel drive switchesMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 11

  • Remove two T40 bolts from the instrument cluster pocketMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 12

  • Remove two T40 bolts in front of the shift knobMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 13

  • Remove two T40 bolts from inside the glove boxMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 14

  • Carefully pull dash toward rear of vehicle by door opening on driver and passenger sidesMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 15

  • Carefully remove dash from vehicle by lifting up and out of the vehicleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 16

  • Remove seats from vehicleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 17

  • If your General is a 4-seat version continue, if you have a 2-seat skip ahead.
    Remove six push pins from the driver and passenger side rear center consoleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG
18

  • Remove two push pins under center console lid and lift up center console and disconnect 12 volt accessory port in center console and remove center console from vehicleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 19

  • Remove two push pins from lower front center console and removeMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 24

  • Remove (4) 13mm bolts and the grab handleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 21

  • Remove six push pins and three T40 boltsMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 22

  • Remove passenger center console side panelMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 23

Subwoofer Enclosure Install

  • Install amplifier plate using two T40 self cutting screws into the two existing holes circled and you may have to remove a wire clip if present and leave screws loose till another stepMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 24
  • Rotate enclosure toward bracket lifting upward and using a 4mm allen wrench loosely install the three M5 button head bolts with thread patch to the top of the enclosureMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 25
  • Rotate enclosure toward bracket lifting upward and using a 4mm allen wrench, loosely install the three M5 button head bolts with thread patch to the top of the enclosureMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 26
  • Tighten three M5 bolts on top of enclosure with a 4mm allen wrench and also tighten two T40 Torx bolts and three Phillips self tapping screws on the front of the plateMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 27

Reassembly

  • Install front passenger center console, carefully sliding into place around subwoofer enclosureMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 28

  • Install six push pins
    NOTE The two up high by firewall will need to be inserted from drivers side by steering wheel.MB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG
29

  • Install three T40 boltsMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 30

  • Install passenger grab handle with four 13mm boltsMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 31

  • Install center cover with two push pinsMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 32

  • If two-seat skip ahead if four-seat, then install rear console and install six push pins on driver and passenger sideMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 33

  • Install rear glove box in rear center console (Remember to connect wires to bottom 12-volt accessory port)MB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 34

  • Install two push pins under glove box lidMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 35

  • Re-install the dash in the vehicleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 36

  • Install key switch and align to detentMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 37

  • ● Install two T40 bolts on driver side instrument cluster areaMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 38

  • Install two T40 bolts in center consoleMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 39

  • Install two T40 bolts in passenger glove boxMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 40

  • Install instrument cluster with two 10mm boltsMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 41

  • Connect instrument cluster connectorMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 42

  • Install top of dash, snapping eight push clips on front of dashMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 43

  • Install six push pins on front of dashMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 44

  • Install hoodMB QUART MBQG-SUB-1 Polaris GENERAL Specific FIG 45

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty period. Components that prove to be defective in materials and workmanship under proper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The costs associated with removal, re-installation, and freight are not the responsibility of Maxxsonics USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith. To view the full warranty, please visit the website.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by MB Quart is under license.
All product names, logos, and brands are property of their respective owners. All company, product, and service names used in this literature are for identification purposes only. Use of these names, logos, and brands does not imply endorsement.
©2021 Maxxsonics USA, Inc.
MBQuart products are designed and engineered in the USA bywww.maxxsonics.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MB QUART User Manuals

Related Manuals