Fontastic 256622 Xtaz Wireless On-Ear Headphone User Manual

Wireless On-Ear Headphone
Xtaz

User Manual

The wireless on-ear headphone Xtaz is your perfect companion to listen to music and for phone calls.

Package contents

• Fontastic® Headphone Chaz
• Micro-USB charging cable
• This user manual

Overview

1. Speaker
2. Height adjustment
3. Headphone strap
4. Volume+ button | Next title 1
5. Multifunction button (On/Off, Telephone, Musik Start/Stop)
6. Volume- button | Previous title
7. Microphone
8. 3.5 mm Line-in connector
9. LED indicator
10. Micro USB connector

LED functions

Getting Started

Charging the battery
The Fontastic® Xtaz is equipped with an internal rechargeable battery. Connect the Xtaz with the micro USB cable which is included in the package contents. The cable can be connected to a computer or a standard USB power supply. The Xtaz`s red LED lights up during the charging process. The usual charging time is 2-3 hours. When fully charged, the red LED goes out. The cable can now be disconnected from the Fontastic® Chaz.

Note: Charge Xtaz for at least 3-4 hours before initial use.

Adjusting the height / turning the speakers
Chaz offers the possibility to adjust the loudspeakers in height to the optimum position for you. To do this, hold the loudspeaker unit up and pull the headphone strap (3) upwards. Adjust the headphones in this way until the ear pads are exactly on the ear. For comfortable wearing around the neck when the headphones are not being used to listen to music, the speakers can be turned outwards.

Switching On /Off
To switch on, press the multifunction button (5) for 3 seconds, an acoustic signal sounds, the blue, and red LED flash alternately.

To switch off, press the multifunction button (5) for 3 seconds, an acoustic signal sounds, the LED goes off.

Pairing

Chaz must be paired with a Bluetooth® device before use. This is a two-part process; one part is carried out on the headphone and the other is carried out on the other Bluetooth® device.

Note: Please note that different mobile phones may require different pairing methods.

1. In the off state, press and hold the multifunction button (5) for 3 seconds to turn it on. Keep the button pressed and wait until the blue and red LED flashes alternately. This indicates the pairing mode.
2. Use your Bluetooth® enabled device to search for Bluetooth® audio devices.
3. The Bluetooth® device should indicate that it has found, Chaz”.
4. Confirm pairing with Chaz. Enter ,,0000″ if you are asked for a pairing code.

If you are unsure about the pairing procedure of your Bluetooth® device, please check your device manual. When using a Bluetooth® transmitter without display, set it to pairing mode and wait a few seconds until the connection with Xtaz is established.

Note: If the connection is lost or the transmitter is temporarily disconnected, briefly press the multifunction button. Chaz will then try to restore the connection.

Connect 2 Xtaz headphones together
Two Xtaz Headphones can be connected via TWS. Two people can listen to the same audio streaming while watching TV, listening to music, gaming, etc.

Turn on both headphones at the same time to connect them together. The headphones connect automatically via TWS. The audio data is now output via both headphones.

Music playback

Start music playback on the Bluetooth® source which is paired with the Chaz. The music is transferred to the Chaz. Stop the music playback on the Bluetooth® source to interrupt the streaming.

To start or stop music playback via the Xtaz, press the multifunction button 5) once. During music playback, the LED blinks blue.
You can use the Xtaz as a wired headphone without Bluetooth® function with the 3.5mm jack cable that is included in the package content. Connect the cable to the 3.5 mm line-in connector (8) of the Xtaz and the audio source, start playing music.

Music control
To play or stop music playback, briefly press the multifunction button (5).

To skip to the previous track, press and hold the Volume- button (6).
To skip to the next track, press and hold the Volume+ button (4).

Note: The mobile phone must support the A2DP and AVRCP profile for music streaming and control. The buttons have no function when using the wired connection. Use the audio source to control the music and volume.

Hands-free features
With its built-in microphone and intelligent noise reduction, the Xtaz is perfectly suitable for phone calls.

Answer/end calls
To accept an incoming call, briefly press multifunction button (5).
To end a call in progress, briefly press multifunction button (5).

Redial
Press the multifunction button (5) twice to redial the last dialed number.

Volume setting
To increase the volume, press and hold the volume + button (4) until the desired volume is reached.

To decrease the volume, press and hold the volume – button (6) until the desired volume is reached.

Technical data:

• BT Version 5
• Profile: Headset, Handsfree, A2DP, AVRCP
• Range: 10m
• Input: 5V DC
• Frequency: 20Hz-20kHz
• Impedance: 32 Ohm
• Built-in microphone
• 3.5 mm line-in connection
• Status LED: Blau/Rot
• Micro USB connector
• Battery Type: 180 mAh Li
• Operation time: Up to 6 hrs.
• Weight: 192g

Safety advice:

• Do not open the device
• Do not hold the device underwater
• Keep it safe from humidity
• Do not connect the adapter to the device by using force
• Keep the device away from children
• Disconnect electronic devices from the power when not using them for a longer time.
• Do not use the device when it has visible defects.

No liability is accepted for any damage caused by incorrect operation.

In case you need technical support, please contact our support team by e-mail under service@fontastic.eu.

Registration and Safety

Certification/General Information
We hereby declare that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the RED 2014/53/EC, as well as the RoHS 2 2011/65/EU directive. The full text of the EU declaration of conformity is available at the following internet address:
www.d-parts.de/Konfo

Note on environmental protection:
After the implementation of the European Directive 2012/19/EC in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste.

Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country.
This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations.
By recycling, reusing the materials, or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks is under license.
Improvement and changes to the technical specifications and other data could be made without prior notice.
Registered trademarks are the property of their respective owners.

Fontastic, by D-Parts GmbH
Birkenweiher Str. 16
63505 Langenselbold, Germany

V2_01_22

Documents / Resources

| Fontastic 256622 Xtaz Wireless On-Ear Headphone [pdf] User Manual
256622, Xtaz Wireless On-Ear Headphone
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>