SOMOGYI ELEKTRONIC NVK Switch Remote Control Lamp Switch Instruction Manual

NVK Switch Remote Control Lamp Switch

Instruction Manual

WIRELESS LAMP SWITCH

WARNINGS

Before using the product for the first time, please read the instructions for use below and retain them for later reference. The original instructions were written in the Hungarian language. This appliance may only be used by persons with impaired physical, sensory or mental capabilities, or lacking in experience or knowledge, as well as children from the age of 8, if they are under supervision or have been given instruction concerning use of the appliance and they have understood the hazards associated with use. Children should not be allowed to play with the unit. Children may only clean or perform user maintenance on the appliance under supervision. After unpacking the unit, confirm that it has not been damaged during transit. Keep the packaging away from children if it contains plastic bags or other potentially hazardous components.

ONLY TO BE INSTALLED BY A PROFESSIONAL.

• Suitable for switching resistive loads (e.g. lamps), may fail when switching inductive consumers; e.g. motor equipment.
• Not suitable for operating 3-pole protective contact devices.
• Due to the presence of the mains voltage comply with the usual rules to protect life. It is forbidden to touch the unit or the connection cable with wet hands!
• Before use, make sure the product has not been damaged. Using a damaged product is prohibited and life-threatening!
• In case of detecting any malfunction, switch off the device and contact a specialist.
• Protect it from dust, humidity, liquids, heat, dampness, frost, shock and direct thermal radiation or sunshine. Use only indoor, in dry circumstances.
• Do not place the switch module in a kitchen, bathroom or in other humid premises.
•  The range is reduced by walls, metal objects, and nearby radio frequency equipment. Do not place the push-button on a metal door frame or fence.
• Do not attempt to disassemble or modify the unit or its accessories, because it can cause fire, accident or electric shock!
• Accidental ringing of the bell may be caused by other radio or electrical equipment in the vicinity. In this case, delete the code with the mini button inside the push-button and re-pair the units.
• If the product has reached the end of its service life, it is classified as hazardous waste together with its accumulator. Handle in accordance with local regulations.
• Somogyi Elektronic Ltd. certifies that this radio-equipment conforms to 2014/53/EU directive. Full text of EU Declaration of Conformity is available at the following address: somogyi@somogyi.hu
• Due to continuous improvements the design and specifications may change without any prior notice. The actual instruction manual can be downloaded from www.somogyi.hu website.
• We don’t take the responsibility for printing errors and apologize if there’s any.

DISPOSAL

Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs arising.

CAUTION:

RISK OF ELECTRIC SHOCK!
Do not attempt to disassemble of modify the unit or its accessories. In case any part is damaged, immediately power off the unit and seek the assistance of a specialist.

NEVER NEEDS BATTERY RELIABLE OPERATION EVEN WHEN COLD

• Maximum output: 230V~ / 3.000W / 13A
• For switching resistive load (e.g. lamp)
• Small, built in switch module
• On/off switch on the module as well
• LED indicators
• Custom encoding with learning function
• Up to 8 push-buttons can be paired with it
• Memory in case of power failure
• Highly water resistant push-button
• Operating range in open terrain: ~120m

INSTALLATION, MOUNTING

The power supply of the push-button is kinetic, no battery is required for its operation. When pressed, the LED indicator flashes briefly. Attach the back of the push-button to the desired location with double-sided adhesive (press for 30 seconds on a smooth, clean surface). It must be installed in a place protected from direct rain and sunlight, not on metal surface. Can also be used as a portable switch. It can also be used as a portable switch. Its expected lifespan is over 100.000 switches.

THE SWITCH MODULE – ONLY TO BE INSTALLED BY A PROFESSIONAL.
Warning! Risk of electric shock! All affected circuits must be disconnected before connection. Not suitable for operating with grounded („GND”) protective contact devices. Only the phase (LIVE) and zero (NEUTRAL) wires can be connected. The insulation must be removed on a 5 mm long part from the end of the 2×1.00mm2 wires before wiring. Make sure that the wires are unloaded. The switch module must be securely fastened with double-sided adhesive or with screws. Must not be accessed by unauthorized people, especially children! It is recommended to be placed in a protected, dry, preferably ventilated place – e.g. into mounting box, behind drywall, etc.

PAIRING

After connecting the switch module as specified, power it on. The pairing mode can be activated by holding pressed the button on the module for 5 seconds. The hidden red LED near the button flashes briefly. Then, you have ~30 sec to firmly press the button on the remote control. The LED on the remote control flashes, and then also the LED on the switch module. Pairing is done. After this, press the module button, or wait 30 sec for automatic memorization. Repeat the process if necessary. In case of a power failure, the pairing will not be deleted.

When exiting the pairing mode, pressing each button on the remote control will turn the lamp connected to the module on and off. The LED built into the module stays on while the module output is under power and it goes out, when turned off. In addition to using the remote control, the lamp can also be switched on by briefly pressing the button on the module. After a possible power failure, the previously switched on lamp will not switch back on or safety reasons.

USE MORE THAN ONE PUSH BUTTONS

If you have more than one remote control, you can pair them (up to 8 pieces). In the above pairing process, push each button to be paired after one another within the available 30 seconds. After the 30 seconds elapsed, all paired push buttons will be stored.

CANCEL PAIRED PUSH BUTTONS

In order to cancel all paired push buttons, press the button of the switch unit and keep it pressed for 10 seconds and then press the same button again to confirm the process. If you do not press any button, the process will be automatically confirmed within 30 seconds. If you keep the button of the switching unit pressed for 10 seconds and then press any push-button, all paired push buttons will be cancelled, and you can use only the currently pressed button to control the switch.

CLEANING

Disconnect the circuits. Use a soft, dry cloth. Do not use aggressive detergents and liquid.

Specifications

Producer
SOMOGYI ELEKTRONIC®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>