GoodEarth 1ft x 4ft LED Flat Panel Installation Guide

GoodEarth 1ft x 4ft LED Flat Panel

SAVE AND ATTACH RECEIPT HERE

Model #: FP1247-AL5-48LFC-G, FP1247-BLK-48LFC-G

Hardware kit

• Actual hardware may differ from illustration

READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

WARNINGS AND CAUTIONS
SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING THE OLD FIXTURE OR INSTALLING A NEW ONE.
Read entire installation procedure before you begin and save instructions for future reference.
THIS FIXTURE IS DIMMABLE BY SPECIFIC FORWARD PHASE ELECTRONIC (TRIAC) DIMMERS. Dimmers tested to be compatible with this fixture are the Lutron: Skylark® SCL-153P, Diva® DVCL-153P, Maestro® MACL-153M, Toggler® TGCL-153P, Lumea® LECL-153P, Caseta® PD-6WCL, Eaton Halo® SAL06P*. (This list of dimmers does not imply any guarantee or warranty of compatibility with a particular application. Dimmers not listed do not imply
non-compatibility.)
If unsure if the electrical box is properly grounded, or the box is plastic and has no ground wire, or are unfamiliar with the methods of properly grounding fixture, consult a qualified electrician.

Important Safety Information

1. Do not look directly at LEDs for extended period of time.
2. For INDOOR use only.
3. Turn power off before servicing.
4. Do not leave bare wires exposed.
5. For electrical requirements, see fixture. Minimum 90 °C supply conductors.

TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH TO JUNCTION BOX OFF

1. Remove mounting plate from LED panel by sliding into the direction of the slots closest to the mounting screws (AA), and then lifting up. Hold the mounting plate up to the junction box in the desired fixture mounting orientation. Pull black, white and ground supply wires from electrical box through the hole in center of mounting plate. Ground wires can be either green or bare copper. Attach mounting plate to the electrical box using mounting screws (AA) provided.

2. Locate the open holes for mounting at the corners of the mounting plate and drill 1/8 in. pilot hole in the center. If a wooden stud is encountered, use the screws (BB) and washers (EE) provided to secure the mounting plate directly to stud.

3. If no stud is encountered, place the drywall anchors (CC) in the pilot holes and screw them into place until flushed with surface of drywall. Place washer (EE) over the mounting hole and drive screws (BB) into drywall anchor until snug. DO NOT OVERTIGHTEN. NOTE: Main support for mounting plate is electrical box when it is secured properly. If the electrical box is not properly secured, alternative mounting methods such as toggle bolts (not included) should be used to secure mounting plate.
   

4. Hold fixture up to secured mounting plate and attach the support wire hooks from the backside of fixture to specially designed slots in mounting plate to temporarily hold fixture for wiring.

5. Fixture must be properly grounded. Connect fixture ground wire to ground wire in electrical box using a wire nut (DD). Ground wires can be either green or bare copper. Connect black supply lead to black fixture wire and white supply lead to white fixture wire using wire nuts (DD). Secure the wire nuts properly to prevent the wires from coming loose. Use cable ties (FF) to secure loose fixture wires to one another in the center of the mounting plate to keep them from getting in the way during fixture mounting. Push excess wire back into the electrical box.
   

6. Keeping the support wire hooks attached to the mounting plate, lift up the LED panel, being careful not to scratch ceiling. Align and insert the 2 metal tabs (on the same side of the mounting plate as the support wires) into the corresponding slots on the LED panel.

7. While keeping the first 2 metal tabs inserted, rotate panel up and insert the 2 remaining tabs on the opposite side.

8. Slide panel until tabs are locked into place. Note that the direction will be either left or right, depending on panel orientation.

9. Slowly release fixture, making sure it stays in place. IMPORTANT: To ensure panel stays in place, locking fastener must be installed. To lock the panel in place, insert a plastic push-in fastener (GG) into the predrilled hole on the side of the panel.
   

5 LIGHT SETTING SLIDE SWITCH

Slide switch that allows the color temperature of the light to be adjusted between 5 values: 6500K, 5000K, 4000K, 3000K, 2700K

Care and Maintenance

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth.
When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

Good Earth Lighting® – 10 YEAR LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application.
The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge.
Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product.
Note: C.O.D. shipments will NOT be accepted.
The liability of the manufacturer is in any case limited to replacement of the defective light fixture product.
The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product.

This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is

1. to person or property or otherwise;
2. incidental or consequential in nature;
3. based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or
4. directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that of the receiver.
4. Consult the dealer or an experienced radio/TV technician for help.

Troubleshooting Guide

Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

PROBLEM

1. Light does not come on.
2. Fuse blows or circuit breaker trips when light is turned on.

POSSIBLE CAUSE

1. Power/ light switch is off.
2. Fixture not properly wired to junction box.
3. Bad switch.
4. Discontinue use.

CORRECTIVE ACTION

1. Verify power supply and light switch are on.
2. Check wiring connections.
3. Test or replace switch.
4. Call customer service (1-800-291-8838).

REPLACEMENT PARTS LIST

Hardware Kit: ZH-FP1247F48

Need Help?
Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc. © 2019 Good Earth Lighting, Inc.
Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>