iOttie HLCRIO175 Cup Holder Mount User Manual
- June 6, 2024
- iOttie
Table of Contents
iOttie HLCRIO175 Cup Holder Mount
Getting Started
For optimal mounting and charging, please follow the detailed instructions within this manual when using the Auto Sense Wireless Charging Mount. iOttie is not liable for possible damages due to product misuse.
- Mount should be aligned so that all 3 spacers contact the inner wall of the cup holder.
- Twist dial to extend spacers so they securely contact the inner wall of the cup holder.
Critical Information
Mounting at a perpendicular angle to the mount works best with the proximity sensor.
If mounting at an angle, phone will need to be very close to sensor for arms to open.
-
Smartphone cases
Reflective Smartphone cases work best. Dark colored or textured cases do not reflect light well, making it difficult for the Proximity Sensor to detect phone. If using a dark colored or textured case, the phone will have to be very close to mount for arms to open automatically. -
Compatibility
Before using product, make sure your device is Qi Wireless compatible. Compatible devices include iPhone X, iPhone Xs, iPhone XR, Samsung Galaxy S10, S10+, Note9+, and Google Pixel 3. -
Qi Wireless Charging in Vehicle
Use the included iOttie Car Charger and Micro USB Cable. If you do use a third party car charger, use a Qualcomm Quick Charge 2.0 or equivalent adapter to receive a wireless charge (with compatible devices).
At a Glance
Connecting Power
Plug the micro-USB cable into the USB port on the back of the Mounting Head.
Insert Car Charger into your vehicle’s power port. Twist Dial to ensure spacers are secure in the cup holder walls.
NOTE:
- Top half of mount rotates 90 degrees for optimal viewing.
- Mount rotates 360 degrees for optimal viewing angles.
Adjusting the Mount
- Foot Knob
Out of box, the foot knob is set to regular sized phones. Foot will need to be adjusted for plus sized phones or cases with thicker bottoms.
Move the knob down until laser etching is aligned appropriately as shown in line drawing.
Using the Auto Sense Mechanism
Once it is unplugged or car is turned off, the Auto Sense’s internal battery
keeps a charge for up to one hour.
Mounting and Charging
- Side arms on mount automatically open via silent step motor for one second when phone is detected in front of Proximity Sensor on mount.
- Once phone is placed in mount, arms will automatically close after one second. Qi wireless charging will start immediately. Releasing Device
- Buttons under the light on both sides of device can also open and close the arms. One or both buttons can be pressed.
The Auto Sense is powered via a Micro-USB cable and coil cell battery. There is no on/off switch on the device. Once it is plugged in, the device will remain on unless the vehicle shuts off power when in parking mode.
Qi Alignment Guide
The Qi Receiver Coil is usually located in the center area of the phone. Check with your phone’s manufacturer for Qi coil location. Below are some examples for commonly used phones.
NOTE:
- For larger/plus phones or larger cases, knob on mount will need to be adju-sted as indicated by laser etching on back for proper alignment with Qi coils.
- The Qi coil on the mount is located at the top, above the iOttie logo. Please follow the guide below to line up your phone with the device for an optimal wireless charging.
Wireless Charger Specifications
INPUT
| DC 9.0V-1.67A DC 5.0V-2.0A
---|---
CHARGING PORT| MICRO USB
LENGTH| 2.96″
WIDTH| 2.75″
HEIGHT| 3.74″ (Foot not extended)
WEIGHT| 4.16oz
Car Charger Specifications
MODEL NUMBER | CHY-CC-U2CQ3C |
---|---|
INPUT | DC 12V~24V |
OUTPUT
| DC 5V – 3A DC 9V – 2A DC 12V – 1.5A
MICRO USB CABLE LENGTH| 120MM
Charging Indicator
S o li d G r e e n L igh t
|
Smartphone charging.
---|---
Blinking R ed Light
| Smartphone not charging.
Foreign object detected or overheating of mount or smartphone.
FCC Part 15 Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
product.
NOTE: This equipment has been tested and found to comply with the limits
for a wireless power transfer, pursuant to Part 15 of the FCC Rules. These
limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, iOttie, Inc declares that the radio equipment type HLCRIO161 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.iottie.com.
Declaration for EU Compliance: Operation Freq: 118.59-151.12 kHz, Max.
RF power transmitted: H-Field 20.35dBμA/m @3m distance.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operational Warnings
- During the charging process, the transfer of electricity gives off heat. Your device may become warm, but should not become exceedingly hot.
- If the device gets wet, please cease charging immediately. Remove all plugs and dry the product completely. Device is only to be operated in a dry, indoor environment.
- Please be careful of excessive drops, dents, punctures, or deformities on the device. If you are concerned, please unplug the device and contact the manufacturer.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Operating this device in a hot environment or in direct sunlight for a long period of time may cause malfunctions. We recommend keeping the product in cooler temperatures.
- Please use included components for an optimal experience. To support
- Qi wireless charge when using a third party car charger or a USB Power Adapter use a minimum output of both “DC 9.0V-1.67A or DC z5.0V-2.0A” and at least QC 2.0.
- The product’s signal could possibly interfere with you TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, please try using your mount in different locations to avoid the signals from interfering with each other.
- California Proposition 65 this product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
THE RECOMMENDED DISTANCE BETWEEN YOU AND THE WIRELESS CHARGING DEVICE SHOULD BE AT LEAST:
DRI V E R S E A T
Knee| 40cm
Leg| 60cm
Body| 70cm
Hands| 30cm
Arms| 70cm
Head| 80cm
F R O N T P A S S E N G E
R S E A T
Knee| 43cm
Leg| 59cm
Body| 62cm
Hands| 46cm
Arms| 55cm
Head| 80cm
All measurements are based on FCAR Car Models as described by the ACRISS Class Clode system.
If you love your iOttie product, let us know by leaving a review online, or connect with us on our social platforms.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>