Fodsports V6 Plus 2 Ways Helmet Intercom User Manual

June 6, 2024
Fodsports

2 Ways Helmet Intercom – V6 Plus

V6 Plus

Operation Manual

Attention:
Thank you for purchasing FODSPORTS V6 Plus (6 RIDERS PLUS) helmet Bluetooth intercom. For best use experiences. please read manual before use.

1. Introduction

Thank you for choosing the FODSPORTS V6 Plus(6 Riders Plus) Motorcyde 6 Riders full-duplex stereo Bluetooth wireless helmet headsets, designed for installing into most open-face, flip-front and full-face style helmets.

With the V6 Plus, you can call hands-free on your Bluetooth mobile phone, listen to music or voice instructions of GPS navigation, and activate wireless intercom for rider to rider or rider to passenger intercom talk within range of 1200 meters(depending on terrain conditions).

The V6 Plus is compliant with Bluetooth Specification V3.0 supporting the following profiles: Headset Profile(HSP), Hands-Free Profile(HFP), and Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile(AVRCP) and Audio Gateway (AG). It supports universal pairing with most Bluetooth headsets on the market. The user can activate Siri or S-Voioe from the main unit for voice dialing and other voice commands. The FM radio tuner is built into the main unit and allows for station scanning.
Superior audio fidelity has been achieved with our high fidelity, non-ported, and ultra-slim helmet HD speakers. This headset also provides the industry’s best combination of wind and ambient noise reduction with the miniature boom microphone.

Please read this User Manual carefully before using this product.

How it works

How it works

2. Packet Content

  • Main Unit
  • HIFI Speaker and Microphone(hard & soft) USB Cable
  • Clip Mounting Bracket
  • User Manual

3. Install Instructions

Fixed Installation Method

  1. Locate the helmet at the left and dean ii up
  2. Peel off the 3M rubber protective film
  3. Apply pressure to the metal carrier to secure the holder firmly

Note: it takes 24 hours after drying

Install Instructions

Temporary installation method

  1. Clip on the left edge of the helmet
  2. Remove metal handle after installation
  3. If required, use additional anti slip rubber patches

Temporary installation method

Install host

  1. Slide V6 Plus host off the top of the clip and you’ll hear a click when it is completely plugged in
  2. Plug in the 3.5mm headset plug

Headset mounting method

  1. Stick the left and right horns of the headphones in the position of the left and right ears of the helmet
  2. Keep the microphone in front of the mouth, Note: microphone holes point to the mouth

Install host

4. Charging

  1. You can charge with the Micro USB cable in the package. During charging, OLEO show “Charging”. After full charging, OLEO show “Charged full”, and ii is recommended to recharge the battery before each use. Suggest full charge before each use.
  2. Low battery warning : Headset will automatically voice prompt low battery at every 5 minutes to prompt the user to recharge it.
  3. Battery state notify: When standby, double press Power button to report battery level.

5. General Operation Instructions

Power on /Power off
Press Power button for approx 3S, the screen display “FODSPORTS”, and it powers on.
When power on status, press Power button for approx. 1 s,the screen display” Power o1f’, and it power off.
Pairing with Cell Phone or GPS and Using

Power

Mobile Phone/GPS pairing steps
1. When power off, press Power button for approx 8S, the screen display “Pairing”, Open the phone Bluetooth, search for “FODSPORTS V6 PLUS”, then dick on the phone connection pair. After the pairing, the screen display “Paired” and goes back to standby mode.

Answer phone calling
The unit will automatically answer the incoming call after 10 seconds. Or press Phone button to answer the incoming phone call immediately.

Reject incoming call
When have incoming calls, double press Power button 2 times to reject within 12s.

End phone calling
During talking, short press Phone button to end the call.

Voice dial
When phone standby, double press Volume – button to make voice dialing (The phone itself must have voice dialing function)

Last number redials
When cell phone standby, double press Volume + button to make last number redialing.

Memory connects with cell phone
Once pairing with cell phone, when power on again, headset will re-connect with mobile automatically. Or in case disconnect during standby mode, short press Phone button will connecting again.

Connect third party calls
When connecting two cell phones, during phone call with first cell phone and second cell phone dial in, can double press Phone two times to answer the second cell phone and hold the first cell phone conversation. When finish the second cell phone conversation, will back to the conversation with fist cell phone.

Music Control
Press the Phone button to play and pause the music. When playing music, double press Volume + button to go to next track, double press Volume – button to go to previous track.

Voice Volume Control
Short press Volume + button or Volume- button adjust the voice volume. Or while music or talking state, long press Volume+ button or Volume – button adjust the voice volume.

6. FM Radio

Tum on/off radio
When in standby mode, press and hold Volume+ button or Volume – button 1 seconds to tum on FM radio. Press and hold ii again for 1 seconds to tum off FM radio.

FM Radio Station Search
While in FM mode, double press Volume + button or Volume – button to seardl a nexVprevious FM channel.
Preset and store up to 6 FM radio stations

In FM radio mode, when a favorite station is found, long press Phone button 1 seoonds to save, a beep tone will sound. Preset and store up 6 FM radio stations. Once 6 stations have been saved, saving a new station will overwrite the oldest saved station. Press Phone button to rotate between each saved station.

7. Universal Pairing and Using

Universal Pairing and Using

Power on other brand Bluetooth device into pairing suitable, meanwhile V6 Plus at standby mode, long press Intercom B button 1 seconds, and screen display “pairing”, then short press Intercom B, and screen display
“Searching”. After pair successfully, the screen display
“Paired”.

After paired, while V6 Plus at standby mode, short press Volume+ and Volume- button at the same times, V6 Plus reconnect with Bluetooth headset which connected before and start talking.
While in talking mode, short press Phone button to end it.

8. Bluetooth Intercom Talk

The V6 Plus can be paired with other V6 Plus for up to a total of 6 units for full duplex Bluetooth intercom. Pairing Two V6 Plus headsets and talk

Bluetooth Intercom Talk

Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 2: After pair finished, Short press Button B on either unit, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.

Pairing Three V6 Plus headsets and talk

Pairing Three V6 Plus headsets and talk

Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 2 : Power on unit 1 and unit 3, then long press unit 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button Con either unit , then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 3: After pair finished, Short press Button Bon unit1 or unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.
Step 4:After pair finished, Short press Button Con unit1 or unit3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press Phone button to exit intercom mode.

Pairing Four V6 Plus headsets and talk

Pairing Four V6 Plus headsets and talk

Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Seardling”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 2: Power on unit 1 and unit 3, then long press unit 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button Con either unit, then the unit’s screen display “Seardling”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 3: Power on unit 1 and unit 4, then long press unit 1 and unit 4 Button D, the screen display “Pairing” of all, then short press Button 4 on either unit, then the unit’s screen display “Seardling”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 4: After pair finished, Short press Button Bon unit1 or unit2, ii will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.
Step 5:After pair finished, Short press Button Con unit1 or unil3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press Phone button to exit intercom mode.

Step 6: After pair finished, Short press Button D on unit1 or unit4, it will start intercom, and sa-een display “Intercom D”. During Intercom talking, short press Phone button to ex[ intercom mode.
Pairing Five V6 Plus headsets and talk

Pairing Five V6 Plus headsets

Step 1: Power on unit 1 and un[ 2, then long press un[ 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either un[, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 2: Power on unit 1 and un[ 3, then long press un[ 1 and unit 3 Button C, the sa-een display “Pairing” of all, then short press Button Con either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 3: Power on unit 1 and un[ 4, then long press un[ 1 and unit 4 Button D, the sa-een display “Pairing” of all, then short press Button 4 on either unit, then the unit’s sa-een display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 4: Power on unit 1 and un[ 5, then long press unit 1 and unit 5 Button E, the screen display “Pairing” of all, then short press Button 5 on either unit, then the unit’s sa-een display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 5: After pair finished, Short press Button Bon unit1 or unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.

Step 6: After pair finished, Short press Button C on unit1 or unit3, it will start intercom, and screen display “Intercom C’. During Intercom talking, short press Phone button to exit intercom mode.

Step 7: After pair finished, Short press Button D on unil1 or unit4, it will start intercom, and screen display “Intercom D”. During Intercom talking, short press Phone button to exit intercom mode.

Step 8: Mer pair finished, Short press Button E on unit1 or units, ii will start intercom, and screen display “Intercom E”. During Intercom talking, short press Phone button to exit intercom mode.

Pairing Six V6 Plus headsets and talk

Pairing Six V6 Plus headsets and talk

Step 1: Power on unit 1 and un[ 2, then long press un[ 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 2: Power on unit 1 and un[ 3, then long press un[ 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button Con either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 3: Power on unit 1 and un[ 4, then long press un[ 1 and unit 4 Button D, the screen display “Pairing” of all, then short press Button 4 on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 4: Power on unit 1 and un[ 5, then long press un[ 1 and unit 5 Button E, the screen display “Pairing” of all, then short press Button 5 on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 5: Let unit 1 and Unit 6 in power off state, then long press unit 1 and unit 6 Power button about 6 seconds, the screen display “Pairing” of all, and short press Power button on either unit, the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.

Step 6: After pair finished, Short press Button Bon unit1 or unit2, it will start intercom, and screen display “Intercom B”. During intercom talking, short press Phone button to exit intercom mode.
Step ?:After pair finished, Short press Button C on unit1 or unit3, it will start intercom, and screen display “Intercom C’. During Intercom talking, short press Phone button to exit intercom mode.
Step 8:Afler pair finished, Short press Button D on unit1 or unit4, it will start intercom, and screen display “Intercom D”. During Intercom talking, short press Phone button to exit intercom mode.
Step 9:After pair finished, Short press Button E on unit1 or units, it will start intercom, and screen display “Intercom E”. During Intercom talking, short press Phone button to exit intercom mode.
Step 1 O:After pair finished, Short press Button power on unit1 or unit6, it will start intercom, and screen display
“Intercom /\’. During Intercom talking, short press Phone button to exit intercom mode.
After third Intercom call

When two device have started the Intercom talking, the other Intercom call in, the unit who be called have tone to notify, and double press Phone button two times on the unit to answer the incoming Intercom call.

Memory clear (intercom ): When device is on, press volume+ button and volume- button at same time for 3 seconds.

9. Technical Specifications

  1. Bluetooth 3.0 Support : HSP,HFP,A2DP,AVRCP, AGHSP
  2. Working hours: 18 hours
  3. Standby time: 300 hours
  4. Charging time: 2 hours
  5. Battery: Lithium containing rechargeable lithium battery 850mAH, 3.7v
  6. Dimensions: 87cm • 45cm • 26cm
  7. Weight: 50g
  8. Certification : CE FCC ROHS TELEC

NOTE: This equipment has been tested and found to comply with the limns for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in a rdance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an ouflet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the use as authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0.904mmis 1.6W/Kg. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID:

FAQs:

How does it work?

The rider can only choose to talk to the captain, and the other riders cannot talk to each other.

Of course, the captain can also call any other rider and talk after passing the permit.

For example: A is the captain, one of the riders (B or C or D or E) can talk to A, but (B, C, D, E) can’t talk to each other.

Can you turn off auto answer?

Sorry, V6 Plus can’t. but Fodsports M1S Pro can switch manual/automatic answering.

Can it be charged through USB?

yes it can

**Can two connected V6 units listen to the same cellphone’s music? And,

can they talk over the intercom while the music is playing?**

Sorry, you can’t listen to the same music, can only listen to your own music separately. And music and intercom functions cannot be performed at the same time. Need to switch. If you need to do it at the same time, you can buy Fodsports M1S pro.

Does the product work with Google Assistant?

Yes! it does.

**Does this include the headset or do I have to purchase it

separately?**

Include! my friend!

Can I pair my iPod and iPhone at the same time?

Yes. it can!

Technical Specifications

Manufacturer Fodsports
Brand FODSPORTS
Item Weight 50 g
Product Dimensions 3.35 x 0.79 x 1.57 inches
Item model number V6 Plus
Batteries 850mAh battery
Manufacturer Part Number V6 Plus

Downloads:

Fodsports V6 Plus 2 Ways Helmet Intercom User Manual (English-Japanese) – [Optimized PDF ]

Fodsports V6 Plus 2 Ways Helmet Intercom User Manual (English-Japanese) – [Original PDF ]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals