Fodsports M1-S Plus Bluetooth Helmet Intercom Headset User Manual

M1-S Plus Bluetooth Helmet Intercom Headset

USER MANUAL

FOCUS ON OUTDOOR SPORTS

1. Package Include:

2. Charging:

1. The function button lights up red when charging, and the red light goes out after finishing(As shown below). Please charge before using for the first time.
2. Please use a qualified charger 5V/1A±0.5A.
3. Please keep charging at least once every 2 months If the product is not used for a long time.

3. Installation & Disassembly

3.1 Speaker Installation

Remark: the microphone should be closed to and aim at the mouth as possible. The speakers are as close to ears as possible. If installation position of the speaker is too deep so that the speaker is too far away from the ear, the sponge in accessory may be used to jack up.

3.2 Fixed by clamp

3.3 Disassembly of the Device

4. Operation (GETTING STARTED)

Outlook / Button

1. Intercom
2. Volume –
3. Volume +
4. Indicator light
5. Function
6. AUX In
7. TYPE-C port (earphones I charging)

Switch On / OFF

Switch On: Long press Intercom button and Function button at the same time for 3 seconds. Voice message will also say” Welcome to FODSPORTS Bluetooth Communication System”.

Switch Off: Long press Intercom button and Function button at the same time for 3 seconds. Voice message will also say “Power off”.

Power Detect & Notification Function
M1-S PLUS has power detect function, when device is on, short press Volume+ and Volume- button at the same lime, recorded voice message will tell you:
Power over 90%
Power over 50%
Power lower than 50%

Low Power Notification
When power lower than 20%, red light flash in the function button and voice message will remind “Power lower than 20%,please recharge immediately”.
When power lower than 10%, red light flash in the function button and voice message will remind”Power lower than 10%,will be turning off. please recharge immediately”.

Cellphone
Answering Call: Short press Function button.
Hangup Call: Call ended, short press Function button.
Refuse Call: Long press Function button for 2 seconds.
Redial: Short press Function button twice.
Volume Up: short press Volume+ button.
Volume Down: short press Volume- button.

Switch manual/automatic answering calls : While in standby, press and hold the intercom button and volume”+””-” button at the same lime for 3 seconds. (Default: answer incoming calls automatically)

Voice Command

When your M1-S PLUS is paired up with cellphone. Short Press Volume+ button and Volume- button once , will automatically switch on the voice command function (only for iOS).
*Cellphone must have voice command function.

Music Function
Play: short press Function button .
Pause: short press Function button .
Volume Up: short press Volume+ button . Volume Down: short press Volume- button . Play Previous: short press Volume+ button twice. Play Next: short press Volume- button twice.

Music Sharing

*Start Sharing Music
For example: A share music with B
Step 1: A connect with phone(refer to 5.3)
Step 2: A and B establish intercom connection(refer to 5.2)
Step 3: Short press intercom button of A to exit intercom mode
Step 4: Long press volume + button about 3 seconds, voice notice “Start Sharing Music”
Step 5:Turn on Music player on your phone and play songs.
Step 6:Now,B can enjoy the music shared by A.

* Stop Sharing Music
Pause music firstly, long press volume + button about 3 seconds,voice notice”Stop Sharing Music”

* About Music Sharing

• Music sharing function is used only between two M1-S plus devices.
• When you start I stop music sharing, the music needs to be in pause status.
• Short press the function button to play/ pause music sharing.
• If the operation of sharing music fails, you need to clear the pairing memory of unit A and unit B, and try again.

Intercom Function
Switch Intercom On: short press Intercom button .
Switch Intercom Off: short press Intercom button.
Volume Up: short press Volume+ button .
Volume Down: short press Volume- button .

Microphone (mute)
Mute Microphone: When the device is in a call (intercom ),long press Volume+ button 2 seconds .
Enable Microphone: When the device is in a call (intercom },long press Volume+ button 2 seconds .
Default: Enable Microphone)

FM Function
FM On: Long press Volume- button for 3 seconds.
FM Off: Long press Volume- button for 3 seconds.
Volume Up: Short press Volume+ button .
Volume Down: Short press Volume- button.
Search channels: short press Volume+/ Volume- button twice.

Memory Clear

Memory Clear: When device is on, press Function and Volume+ buttons at the same time for 5 seconds. Then M1-S PLUS will clear the pairing memory with other devices. The red and blue lights flash at the same time, clearing memory completely.

5. Device Pairing

5.1 Pairing Modes
5.1.1 Passive pairing mode

When device is on. long press Function button to enter Pairing Mode. red and blue lights flash quickly. voice notice” pairing “. Pairing mode for connection to Bluetooth devices such as mobile phones and Bluetooth GPS.

5.1.2 Active search mode

When device is on. long press Intercom button to enter Search Mode , red and blue lights flash slowly, voice message says “Searching”. Search mode only use for intercom function connection between M1-S PLUS devices.

5.2 (A)M1-S PLUS connect with (B)M1-S PLUS

A M1-S PLUS is on active search mode(refer to 5.1.2), B M1S-PLUS is on passive search mode(refer to 5.1.1),A and B M1-S PLUS change from flashing red and blue lights alternately to function and intercom buttons flashing blue lights at the same time, connect successfully.

5.3 Pairing With Cellphone

STEP-1. When device is on, long press Function button. red and blue light flash quickly, entering passive pairing mode.(refer to 5.1.1)

STEP-2. Turn on cellphone Bluetooth, choose” FODSPORTS M1-S PLUS”, the pairing is complete. Voice message will notice “Device Connected”.

5.4 Connect with two phones

Step-1 . Connect to the first phone(refer to 5.3)
Step-2 . Long press the Function button, M1-S PLUS on passive search mode, connect to the second phone(refer to 5.3)

Notice: M1-S PLUS can connect with two phones, but only support one phone for audio input.

5.5 Wire Connecting

Any device with 3.5mm connector can transmit voice signal lo M1-S PLUS.
When device wire connected by 2.5mm to 3.5mm cable to M1-S PLUS, Complete the wired sound source input.

You need lo purchase a cable if you need a wired connection for Walkie-talkie equipment.

6. Multi-device pairing connection

6.1 Occasions: Rider A connect with Passenger B for intercom. Then A connect with two Bluetooth devices and one wired equipment and B connect with one Bluetooth device(as shown below).

Step 1 . A M1-S PLUS connect with B M1-S PLUS(refer to 5.2)
Step 2. Short press one time A or B intercom button to disconnect intercom
Step 3. A connect with 2 phones(refer to 5.4)
Step 4. A use 2.5 mm to 3.5 mm AUX audio line to connect with one audio device
Step 5. B connect with one phone(Bluetooth device)
Step 6. Short press intercom button of A or B for connection.
Notice: If A or B need to use the audio function of phone(Bluetooth device), you need to disconnect the intercom.

6.2 Multiple Intercom
6.2.1 M1-S PLUS equipped with multiple intercom function, recommended 4 units(A,B,C,D), pairing procedure as follow:

Step 1: Unit A is on active search mode(refer to 5.1.2), Unit B is on passive search mode(refer to 5.1.1 ), Unit A and Unit B change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time,connect successfully.Short press the intercom button of Unit B for one time, exit intercom state temporarily.

Step 2: Unit B is on active search mode(refer to 5.1.2), Unit C is on passive search mode(refer to 5.1.1 ), Unit B and Unit C change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time, connect successfully. Short press the intercom button of Unit C for one time, exit intercom state temporarily.

Step 3: Unit C is on active search mode{refer lo5.1.2), UnitD is on passive search mode{refer lo 5.1.1 ), Unite and Unit D change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same lime, connect successfully.

Step 4: The intercom buttons and function buttons of Unit A ,B ,C and D flash blue light at the same time, the connection of group intercom successfully.
*You can connect more M1-S PLUS by repeating the above methods.

Notice: The first and the last one M 1 S-PLUS can connect with another 2 Bluetooth devices. The
M1 S-PLUS in the middle connection position of the group can connect with an additional Bluetooth device.
For example: When in the group intercom mode, Unit B and C can only connect with one Bluetooth device. Unit A and D can connect with two Bluetooth devices.

*Intercom Interruption
In multiple intercoms mode, if there is an incoming call caused one unit away from the connection, after call, will reconnected automatically. If interruption is caused by distance or bad signal, please press intercom button to reconnect.

6.2.2 Memory Connection Function
M1-S PLUS will remember paired units. but after switch off and want to reconnect again. please follow the procedure:

STEP-1. Switch off all 4 units(A,B,C,D) and all Bluetooth devices connected to the headset such as cellphone and GPS. (II will affect the pairing)

STEP-2. Switch on all 4 units(A,B,C,D) in the same time(long press intercom and function buttons about 3 seconds).

STEP-3. Short press one intercom button of the 4 M1S-PLUS and they flash blue and red lights in the same time. Memory connection start successfully.

STEP-4. After all 4 units reconnected , switch on original connected Bluetooth devices such as cellphone and GPS.

6.2.3 Four-persons intercom quick connection method (Fast Pairing Mode)

Step-1 :Switch on 4 M1 S-Plus of ABC and D.

Step-2: Unit AB C and Dare all on passive search mode by long pressing function buttons.4 Units are flash blue and red lights alternately, voice notice “pairing”.

Step-3: Short press the function button of one M1-S PLUS for one time,4 units keep flashing blue and red light alternately.
Step-4: After 15 seconds, Voice notice “Searching” of 4 units , the function buttons and intercom buttons flash blue lights at the same time, group intercom connection finish successfully.
*Notice: Fast pairing mode only for 4 riders use.

7. Technical Specifications

• Bluetooth Support: HSP, HFP, A2DP, AVRCP, AGHSP
• Battery: lithium battery, 900mA, 3.7v
• Dimensions: 8.6cm 4.4cm 2.5cm
• Weight: 44G, 92G(include Headphone & Mic Kits)
• Frequency Range: 2.4G-2.485G
• Operating temperature: -20″C-50C
• Certification: CE FCC ROHS BQB TELEC
• USB Adapter standard charge voltage: DC 5V±0.2V USB
• Adapter standard charge circuit: DC 1 A±0.5A Charging lime: 2-3 hours

8. Q &A / Warning

Q1: No sounds from one or two side speaker.
A1 : Check device plug, needs to firmly connected.

Q2: Can it be recharged from bike USB charger while riding 7
A2: 1.Not recommended, unstable power source will cause damage on internal circuit, may cause unable to recharge/can’t fully charged/can’t switch on.
2.Power bank will be good.

Q3: When using radio, not transmission or continuous transmission.
A3: Check 2.5mm pin, has to insert firmly. The pin equipped with waterproof aprons, user might think its already plugged.

Q4: New device can’t switch on.
A4. Recharged at least 30 minutes before switch use.

*Warning
Sound Volume Warning
Long periods of listening or having the volume too high may damage your hearing.

Disassemble or Modification
The M1-S PLUS is precisely made in factory. Any disassemble or modification may damage the device, please do not tear any of the safety regulation and serial sticker from the device ,that will void the warranty. Please contact us directly if needed .

9. Statement / Warranty

9.1 FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject lo the following two conditions (1) this device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

9.2 Warranty
In normal use.one year warranty from the date of purchase any disassemble modification will void warranty.

After-Sale Service
For any quality problem or missing accessories, especially pairing problem between 2 or more M1-S PLUS headsets, please feel free to contact us at email: winzon.cs@outlook.com. We’re always here ready lo help, will reply lo you in 12 hours.

FAQs:

Why are my two speakers or one side speaker unavailable/no sound?

A: 1. Please check if the headphone cable is inserted in the correct direction, M1-S PLUS is a Type-C interface, with the microphone icon facing you, and then inserting the interface is the correct direction. 2. Please make sure the headphone cable is fully inserted into the interface.

Why is my microphone unavailable/no sound?

The microphone part is detachable and can replace the soft/boom microphone, so please check if this part is inserted tightly. 2. Please check if the headphone cable is inserted in the correct direction, M1-S PLUS is a Type-C interface, with the microphone icon facing you, and then inserting the interface is the correct direction.

Why are my speakers volume low?

Different locations of speakers will cause differences in volume, please install the speaker as close to your ears as possible. If the distance is too far, the volume will be reduced. You can use the thickened pad in the package to achieve it.

Why is the volume of the intercom really low?

Please note that both the volume of the intercom or the volume of listening to music can be adjusted with the volume +- button, if you think the intercom volume is too low, you can press “+” button to increase the intercom volume.

My friend and I both use M1-S PLUS, why can I hear his voice, but he

can’t hear me?

It may be that his speaker is defective. Please ask him to connect the phone and play music to check if it is the speaker problem. 2. It may also be that your microphone is defective and he cannot hear your voice. Please replace the soft/hard microphone to check if it is the microphone problem.

Why did music sharing fail?

Music sharing function only applicable between 2 M1-S PLUS units. 2. When you start/stop music sharing, the music needs to be in pause status, if you don’t pause the music, it will fail to share music.

What should I do if the accessories or unit of M1-S PLUS defective?

Any accessories defective or unit defective can come to us and we will help you.

To contact Customer Service, please

SEND US A FORM

We suggest The outdoor signal need to be at least 2 bar  , to make sure the booster can work.

Technical Specification

Downloads

Fodsports M1-S Plus Bluetooth Helmet Intercom Headset Manual  – [Optimized PDF ]

Fodsports M1-S Plus Bluetooth Helmet Intercom Headset Manual – [Original PDF ]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>