FODSPORTS M1-S Pro Helmet Bluetooth Intercom User Manual

FODSPORTS M1-S Pro Helmet Bluetooth Intercom User Manual

Package Include

M1-S PRO

Speakers& Hard Tube Microphone

USB Cable

Wired Microphone

2.5mm to 3.5mm Cable

Unit base

Metal Clip

3M Glue Velcro

Velcro

EVA Booster

User Manual

User Guide

Charging

1. The function button lights up red when charging, and the red light goes out after finishing(As shown below).
   Please charge before using for the first time.

2. Please use a qualified charger 5V/1A±0.5A.

3. Please keep charging at least once every 2 months If the product is not used for a long time.

Installation & Disassembly

Speaker Installation

1.  Open the inner helmet lining on the ear position and attach the velcro loops.

2. Attach the Headphone with Velcro hook to the loop (the short-line speaker is on the left)

3. Place Velcro on the right position on the left side of the helmet, match the microphone with the mouth position, and tidy up the cable and lining.

Remark: the microphone should be closed to and aim at the mouth as possible. The speakers are as close to ears as possible. If installation position of the speaker is too deep so that the speaker is too far away from the ear, the sponge in accessory may be used to jack up.

4. Fixed by clamp

5. Find and assemble the Unit base and metal clip.
   

6. Fix the base on the right position.

7. Assemble the M1 S-PLUS: Insert the snap of the bottom of the host in to the groove of the base, press the host to the base so that the clip of the base buckle the top of the host.
   

8. Insert the microphone and earphone connection line, installation complete.

Disassembly of the Device

1. Pull out the headset plug.

2. Press the upper clamp buckle and move the device upward to remove it.
   

Button and basic function operation

Outlook / Button

1. Intercom
2. Volume –
3. Volume +
4. Function
5. MICRO-5Pin port ( charging / Data )
6. AUX In
7. Speaker/microphone assembly insert hole

Switch On / OFF
Switch On: Long press Intercom button and Function button at the same time for 3 seconds,Voice message will also say “ Welcome to FODSPORTS Bluetooth Communication System”.
Switch Off: Long press Intercom button and Function button at the same time for 3 seconds. Voice message will also say “Power off ”.
*For first time use, please recharge the device until the red light is off

Power Detect & Notification Function
M1-S PRO has power detect function, when device is on, long press Function button and Volume- button at the same time for 3 seconds, recorded voice message will tell you:
Power over 90%
Power over 50%
Power lower than 50%

Low Power Notification
When power lower than 20%, red light flash in the function button and voice message will remind “Power lower than 20%,please recharge immediately”.
When power lower than 10%, red light flash in the function button and voice message will remind“ Power lower than 10%,will be turning off. please recharge immediately”.

Cellphone

• Answering Call: Short press Function button.
• Hangup Call: Call ended, short press Function button.
• Refuse Call: Long press Function button for 2 seconds.
• Redial: Short press Function button twice.
• Volume Up: Short press Volume+ button.
• Volume Down: Short press Volume- button.

Voice Command

Short press function button once
Automatically switch on voice command input function

When your M1-S PRO is paired up with cellphone. Short press function button once will automatically switch on the voice command function (only for iOS and Android ).
Cellphone must have voice command function.

Music Function

• Play: Short press Volume+ button twice.
• Pause: Short press Volume+ button twice.
• Volume Up: Short press Volume+ button once.
• Volume Down: Short press Volume- button once.
• Play Previous: Long press Volume+ button 2 seconds.
• Play Next: Long press Volume- button 2 seconds.

Intercom Function

• Switch Intercom On: Short press Intercom button.
• Switch Intercom Off: Short press Intercom button.
• Volume Up: Short press Volume+ button .
• Volume Down: Short press Volume- button .

Memory Clear

Memory Clear: When device is on, press Function and Volume+ buttons at the same time for 5 seconds. Then M1-S PRO will clear the pairing memory with other devices. The red and blue lights flash at the same time, clearing memory completely.

Device Pairing

1. Pairing Modes

2. Passive pairing mode
   When device is on, long press Function button to enter Pairing Mode, red and blue lights flash quickly, voice notice “ pairing ”. Pairing mode for connection to Bluetooth devices such as mobile phones and Bluetooth GPS.

3. Active search mode
   
   When device is on, long press Intercom button to enter Search Mode , red and blue lights flash slowly, voice message says “ Searching ”.Search mode only use for intercom function connection between M1-S PRO devices.

4. (A) M1-S PRO connect with (B) M1-S PRO
   
   A M1-S PRO is on positive search mode(refer to 5.1.2), B M1-S PRO is on passive search mode(refer to 5.1.1),A and B M1-S PRO change from flashing red and blue lights alternately to function and intercom buttons flashing blue lights at the same time, connect successfully

5. Pairing With Cellphone
   
   STEP1.When device is on, long press Function button, red and blue light flash quickly, entering passive pairing mode.(refer to 5.1.1)
   STEP2.Turn on cellphone Bluetooth, Select“ FODSPORTS M1-S PRO”, the pairing is complete. Voice message will notice “Device Connected”.

6. Connect with two phones
   
   Step1. Connect to the first phone(refer to 5.3)
   Step2. Long press the Function button, M1-S PRO on passive search mode, connect to the second phone (refer to 5.3)
   Notice: M1-S PRO can connect with two phones, but only support one phone for audio input.

7. Wire Connecting
   Any device with 3.5mm connector can transmit voice signal to M1-S PRO.
   When device wire connected by 2.5mm to 3.5mm cable to M1-S PRO,Complete the wired sound source input.
   Long press the [Volume+] and [Volume-] buttons for 3 seconds to turn on or turn off the wired audio input.
   You need to purchase a cable if you need a wired connection for Walkie talkie equipment.

Multi-device pairing connection

1. Occasions: Rider A connect with Passenger B for intercom. Then A connect with two bluetooth devices and one wired equipment and B connect with one bluetooth device(as shown below).
   

   • Step 1. A M1-S PRO connect with B M1-S PRO(refer to 5.2)
   • Step 2. Short press one time A or B intercom button to disconnet intercom
   • Step 3. A connect with 2 phones(refer to 5.4)
   • Step 4. A use 2.5 mm to 3.5 mm AUX audio line to connect with one audio device
   • Step 5. B connect with one phone(bluetooth device)
   • Step 6. Short press intercome button of A or B for connection.
     Notice: If A or B need to use the audio function of phone (bluetooth device), you need to disconnect the intercom.

2. Multiple Intercom
   M1-S PRO equipped with multiple intercom function, recommended 4 units(A,B,C,D), pairing procedure as follow:
   Step 1: Unit A is on positive search mode(refer to 5.1.2), Unit B is on passive search mode(refer to 5.1.1),
   Unit A and Unit B change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time, connect successfully. Short press the intercom button of Unit B for one time, exit intercom state temporarily.
   Step 2: Unit B is on positive search mode(refer to 5.1.2), Unit C is on passive search mode(refer to 5.1.1),
   Unit B and Unit C change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time, connect successfully. Short press the intercom button of Unit C for one time, exit intercom state temporarily.
   Step 3: Unit C is on positive search mode(refer to5.1.2), UnitD is on passive search mode(refer to 5.1.1),
   UnitC and Unit D change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time, connect successfully.
   Step 4: The intercom buttons and function buttons of Unit A ,B ,C and D flash blue light at the same time, the connection of group intercom successfully.
   *You can connect more M1-S PRO by repeating the above methods.
   Notice: The first and the last one M1-S PRO can connect with another 2 Bluetooth devices. The M1-S PRO in the middle connection position of the group can connect with an additional Bluetooth device.
   For example: When in the group intercom mode, Unit B and C can only connect with one bluetooth device. Unit A and D can connect with two bluetooth devices.
   *Intercom Interruption
   In multiple intercoms mode, if there is an incoming call caused one unit away from the connection, after call, will reconnected automatically. If interruption is caused by distance or bad signal, please press intercom button to reconnect.

3. Memory Connection Function
   M1-S PRO will remember paired units, but after switch off and want to reconnect again, please follow the procedure:
   
   STEP1. Switch off all 4 units(A,B,C,D) and all Bluetooth devices connected to the headset such as cellphone and GPS. (It will affect the pairing)
   STEP2. Switch on all 4 units(A,B,C,D) in the same time(long press intercom and function buttons about 3 seconds).
   STEP3. Short press one intercom button of the 4 M1-S PRO and they flash blue and red lights in the same time. Memory connection start successfully.
   STEP4. After all 4 units reconnected , switch on original connected Bluetooth devices such as cellphone and GPS.

Technical Specifications

Bluetooth Support: HSP,HFP,A2DP,AVRCP, AGHSP
Battery: lithium battery, 900mAh , 3.7v
Dimensions: 8.7cm 4.2cm 2.3cm
Weight: 44G, 92G(Include Headphone & Mic Kits)
Frequency Range: 2.4GHz～2.485GHz
Operating temperature: -20℃～50℃
Certification: CE FCC ROHS BQB TELEC
USB Adapter standard charge voltage: DC 5V±0.2V
USB Adapter standard charge circuit: DC 1A±0.5A
Charging time: 2～3 hours

Q & A / Warning

• Q1：No sounds from one or two side speaker.
  A1： Check device plug, needs to firmly connected.

• Q2：Can it be recharged from bike USB charger while riding ?
  A2 ：Not recommended, unstable power source will cause damage on internal circuit may cause unable to recharge/can’t fully charged/can’t switch on.

1. Power bank will be good.

• Q3：When using radio, not transmission or continuous transmission.
  A3：Check 2.5mm pin, has to insert firmly. The pin equipped with waterproof aprons, user might think its already plugged.

• Q4：New device can’t switch on.
  A4：Recharged at least 30 minutes before switch use.

Warning
Sound Volume Warning
Long period or too loud may hurt hearing ability.

Disassemble or Modification
The M1-S PRO is precisely made in factory. Any disassemble or modification may damage the device, please do not tear any of the safety regulation and serial sticker from the device ,that will void the warranty. Please contact us directly if needed .

Statement / Warranty/After-Sale Service

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules.Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

After-Sale Service

For any quality problem or missing accessories, especially pairing problem between 2 or more M1-S PRO headsets, please feel free to contact us at email: winzon.cs@outlook.com. We’re always here ready to help, will reply to you in 24 hours.

• * 

References

• M1-S Pro User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>