SYNCO G1T Microphone Wireless for Smartphone User Manual

SYNCO G1T Microphone Wireless for Smartphone

Thank you for choosing SYNCO product.
Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your SYNCO Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping, impact of external force.
• Do not attempt to disassemble the product. Doing so voids warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions happened.
• Failure to follow all the instructions may result in mechanics damage. Warranty does not apply to human errors.

Package List

Product Instruction

TX Transmitter.

1. External Mic Input
2. USB-C Port
3. Power/ Mute
4. Reset(Help with Eject Pin)
5. Low Cut
6. Pairing
7. Built-in Mic
8. Pocket Clip
9. Pairing/ Muting Indicator
10. Power Indicator

RX Receiver

1. Vocal Effects
2. Pairing/ Gain Control
3. USB-C Port
4. Detachable Connector
5. 3.5mm In-Ear Monitoring Jack
6. Pairing Indicator

Indicator — TX Transmitter

Indicator — RX Receiver

Operations

TX

1. Power/ Mute
   Long Press 3s: turn on/off the system Short Press: mute/unmute the microphone

2. Charging
   5V/2A;
   Please fully charge the product before use with USB-C charging cable.

3. External Mic Input
   TRS Mic Only
   (Note: When using an external mic, please insert it into the mic input properly.)

4. Mic Windshield & Device Installation

5. Reset
   Gently poke the pin into Reset for 3 seconds to restore factory defaults.

6. Low Cut
   Short Press: 150Hz Low Cut On Short Press again: Low Cut Off

7. Pairing
   The system will pair automatically after power on.
   Manual pairing: long press the pairing button on the RX and TX for 3 seconds at the same time

RX

1. Vocal Effects
   Short press to switch sound effects: Original – Studio FX – KTV FX – Voice Amplification – EDM (Electronic Dance Music) – Baby FX – Male to Female – Female to Male – Monster FX

2. Pairing/ Gain Control
   The system will pair automatically after power on.
   Manual pairing: long press the pairing button on the RX and TX for 3 seconds at the same time Gain Control: 0-3 Level
   Each short press increases gain by one level.

3. USB-C Port
   For charging phone device

4. Detachable Connector
   G1T: Type-C connector
   G1L: Lightning connector
   Extra Type-C or Lightning connector is available separately to adapt RX to more phone devices.

5. 3.5mm In-Ear Monitoring Jack
   For real-time monitoring mic recording and device’s backgrounding with headphones

Specifications

TX Transmitter

RX Receiver

164ft/50m(NLOS area)

Sampling Rate| 48KHz
Bit Depth| 16Bit
Antenna| Built-in
Number of Audio Channels| 2
Monitoring| 3.5mm In-Ear Monitoring
Audio Output| Lightning or Type-C Output
Gain| 0-3 Level
Power Requirements| 5V 1A
Dimensions| 55X31X13mm
Material| ABS
Weight| 12g

Microphone

Warranty

Warranty Period
Thank you for purchasing SYNCO products.

1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.

Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
Faults resulted from inappropriate use of a product without following its operation specification

• Artificial damage, e.g. crash, squeeze, scratch, or soaking
• Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration
• The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
• All consumable accessory attached to a product, like cable, wind muff, battery
• Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

• If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at support@syncoaudio. com.
• Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
• If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.

WARRANTY CERTIFICATE

WARRANTY CERTIFICATE

Please register yuosuvriawEamrrail：ty.sMupeapnowrth@ilsey,nycoouaaurdeiow.ceolcmomed to contact

UINSFEORRMATION

| Customer Name:
Phone Number:
Email:
Address:

SINAFLOERSMATION

| Sales Date:
Model:
Product Code:
Dealer:

REPCAOIRRD

| Service Date:
Technician:
Issue:

Guangzhou Zhiying Technology Co., Ltd

Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
support@syncoaudio.com
www.syncoaudio.com
https://www.facebook.com/syncomicrophones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>