LEDLyskilder R8-1 Ultrathin Touch Wheel RF Remote Controller Instruction Manual
- June 4, 2024
- LEDLyskilder
Table of Contents
R8,R8-1 Ultrathin Touch Wheel RF Remote Controller
Ultrathin Touch Wheel RF Remote Controller
Model No.: R8/R8-1
1 and 4 zone RGB or RGBW/Touch color wheel/Wireless remote 30m distance/CR2032
battery
Features
- Apply to RGB or RGBW LED controller.
- Ultra sensitive color adjustment touch wheel.
- Each remote can match one or more receivers.
- 2032 battery powered.
- Operate with LED indicator light.
Technical Parameters
Input and Output
Output signal| RF 2.4GHz ( Operation )
Working voltage| 3VDC CR2032
Working current| <5mA
Standby current| <10μA
Standby time| 1 year
Remote distance| 30m(Barrier-free space)
Environment
Operation temperature| Ta: -30 O C ~ +55 O C
IP rating| IP20
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Warranty
Warranty| 5 years
Weight
Gross weight| 0.037kg
Net weight| 0.062kg
Mechanical Structures and Installations
User Manual Ver 1.1.1
|
---|---
Note: Before the first use, please remove the protective film on the
battery.
To fix the remote, two options are offered for selection:
Option 1: fix the remote’ back holder on the wall with two screws.
Option 2: adhere the remote’ back holder to the wall with paster.
Note: If the LED indicator is not on when press key, it is due to dead
battery or bad contact caused by multiple plugging, please replace the
battery, or raise the battery shrapnel with a screwdriver.
Operation
- When light is on, touch the color wheel, the indicator will display red.
- To extend battery life, no touch or press key operation after a few seconds, the touch wheel will enter sleep state, you need press any key to make touch wheel quit sleep state.
Match Remote Control (two match ways)
The end users can choose the suitable match/delete ways. Two options are
offered for selection:
Use the controller’s Match key
Match: Short press the match key, immediately press on/off key (single zone
remote) or zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times means match is successful.
Delete: Press and hold the match key for 5s to delete all match, The LED
indicator fast flash a few times means all matched remotes were deleted.
Use Power Restart
Match: Switch off the power, then switch on the power, repeat again. An
immediately short press on/off key (single zone remote) or zone key (multiple
zones remote) 3 times on the emote. The light blinks 3 times means the match
is successful. .
Delete: Switch off the power, then switch on the power, repeat again. An
immediately short press on/off key (single zone remote)or zone key (multiple
zones remote) 5 times on the remote. The light blinks 5 times means all
matched remotes were deleted.
Key function
- R8 4 zone RGB/RGBW remote
|
---|---
Color| R/G/B value
---|---
Red| R100%| GO%| BO%
Yellow| R100%| G100%| BO%
Green| RO%| G100%| BO%
Cyan| RO%| G100%| B100%
Blue| RO%| GO%| B100%
Purple| R100%| GO%| B100%
White| R100%| G100%| B100%
On/Off: Short press turn on/off all zone lights.
1,2,3,4 zone: Short press select and turn on zone light, long press 2s
turn off zone light.
Short press the multiple zone key fastly, will synchronous select multiple
zone synchronously.
Color wheel: Touch to change the current zone static RGB color.
Mode: Short press run the next dynamic mode, long press 2s run mode
cycle.
Bright+/-: Static color, adjust brightness, short press 10 levels, long
press 1-6s for continuous 256 levels adjustment.
Speed+/- : Dynamic mode, adjust speed, short press 10 levels, long press
2s get the fastest or slowest speed.
W: For RGB light, short press turn on/off white(RGB mix), long press 1-6s
adjust saturation continuously, namely change current static RGB color to
mixed white slowly.
For RGBW light, short press turn on/off W channel, long press 1-6s adjust W
brightness continuously.
Scene: Short press recall the scene, long press 2s save. 5the LED
indicator will light up longer when save OK. 4 zone recall or save
synchronously.
- R8-1 1 zone RGB/RGBW remote
On/Off: Turn on/off
light.
Color wheel: Touch to change static RGB color.
Mode: Short press run the next dynamic mode, long press 2s run mode
cycle.
Speed/Saturation: For dynamic mode, adjust speed, short press 10 levels,
long press 2s get the default speed.
For static color, adjust saturation, namely change current static RGB color to
mixed white slowly, short press 11 levels, long press 1-6s for continuous 256
levels adjustment.
Bright+/-: Adjust brightness, short press 10 levels, long press 1-6s for
continuous 256 levels adjustment.
R G B: Short press get red green or blue color directly, long press 1-6s
adjust R/G/B brightness continuously to achieve millions of colors.
continuously
W+/-: For RGB light, short press turn on/off white(RGB mix), long press
1-6s adjust saturation, namely change current static RGB color to mixed white
slowly.
For RGBW light, short press turn on/off W channel, long press 1-6s adjust W
brightness continuously.
Scene: Short press recall the scene, long press 2s save the current color
into the scene. the LED indicator will light up longer when save OK.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing the battery, pay attention to the battery’s positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle the remote, beware of falling.
-
For indoor and dry location use only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>