LEDLyskilder V1-L/P Single Color LED Controller User Manual

June 4, 2024
LEDLyskilder

Single Color LED Controller
Model No.: V1-L/P

Single Color LED Controller

1 Channel/Step-less dimming/Wireless remote control/Push Dim/Four PWM frequency/Linear or logarithmic dimmingLEDLyskilder V1 LP Single Color LED
Controller

Features

  • 4096 levels 0-100% dimming smoothly without any
  • Match with RF 2.4G single zone or multiple zones dimming remote control.
  • One RF controller accepts up to 10 remote control.
  • Auto-transmitting function: Controller automatically transmits a signal to another controller with a 30m control distance.
  • Synchronize on multiple controllers.
  • Connect with external push switch to achieve on/off and 0-100% dimming function.
  • Logarithmic or linear dimming curve selectable.
  • PWM frequency 500Hz, 2kHz, 8kHz or 16kHz selectable.
  • Over-heat / Over-load / Short circuit protection, recover automatically.
  • Light on/off fade time 3s selectable.

Technical Parameters

Input and Output

Input voltage 12-48VDC
Output voltage 12-48VDC
Output current 15A@12/24V

10A@36/48V
Output power| 180W@12V
360W@24V
360W@36V
480W@48V
Output type| Constant voltage

Dimming data

Input signal RF 2.4GHz + Push Dim
Control distance 30m(Barrier-free space)
Dimming range 4096 (2^12) levels
Dimming grayscale 0 -100%
Dimming curve Logarithmic or linear
PWM Frequency 500Hz, 2kHz, 8kHz, 16kHz

Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED

Environment

Operation temperature Ta: -30O C ~ +55 O C
Case temperature (Max.) T c: +85OC
IP rating IP20

Warranty and Protection

Warranty 5 years
Protection Reverse polarity

Over-heat
Over-load
Short circuit

Mechanical Structures and Installations

LEDLyskilder V1 LP Single Color
LED Controller - Mechanical

Wiring Diagram

Match with dimming remoteLEDLyskilder V1 LP Single Color LED Controller -
Diagram

Connect with push switch![LEDLyskilder V1 LP Single Color LED Controller

Use the controller’s Match key Use Power Restart

Match:
Short press match key, and immediately press the on/off key (single zone remote) or zone key (multiple zones remote) on the remote.
The LED indicator fast flash a few times means the match is successful.
Delete:
Press and hold the match key for 5s to delete all match, The LED indicator fast  flash a few times means all matched remotes were deleted.| Match:
Switch off the power, then switch on the power, and repeat again.
An immediately short press on/off key (single zone remote) or zone key (multiple zones remote) 3 times on the remote.
The light blinks 3 times means the match is successful.
Delete:
Switch off the power, then switch on the power, and repeat again.
An immediately short press on/off key (single zone remote) or zone key (multiple zones remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.

Application notes

1. All the receivers in the same zone.LEDLyskilder V1 LP Single Color LED
Controller - Application

Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
Strong signal sources such as WiFi routers and microwave ovens will affect the range.
We recommend for indoor applications that receiver placements should be no further apart than15m.

2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.

LEDLyskilder V1 LP Single Color LED Controller -
different

Light on/off fade time
Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

  • Short press:
    Turn on or off light.

  •  Long press (1-6s):
    Press and hold to step-less dimming,
    With every other long press, the light level goes to the opposite direction.

  •  Dimming memory:
    Light returns to the previous dimming level when switched off and on again, even at power failure.

  • Synchronization:
    If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to  100%.
    This means there is no need for any additional synchrony wire in larger installations.
    We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to the controller should be no more than 20 meters.

PWM frequency setting

We can select four PWM frequencies: 500Hz, 2kHz, 8kHz, or 16kHz.
Higher PWM frequency will cause lower output current, and higher power noise, but more suitable for the camera(No flickers for video).

Dimming curve setting

LEDLyskilder V1 LP Single Color LED Controller -
Dimming

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals