anslut 013870 Heater Fan Instruction Manual

: June 6, 2024
: anslut

Table of Contents

SAFETY INSTRUCTIONS
- SYMBOLS
TECHNICAL DATA
DESCRIPTION
USE
MAINTENANCE
- STORAGE
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

anslut 013870 Heater Fan Instruction Manual

Care for the Enviroment

Recycle Discarded Product in Accordance with Local Regulation

SAFETY INSTRUCTIONS

Keep children less than 3 years old under supervision when they are near the product. The product can be switched on/off by children from 3 to 8 years old only if it is mounted in the correct position to use, and if they are supervised or receive instructions concerning the safe use of theproduct and understand the risks involved. Do not allow children from 3 to 8 years old to connect, use, clean or maintain the product.
This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision. Keep children less than 3 years old under supervision when they are near the product.
The product is only intended for household use.
Pull out the plug if the product is not going to be used for some time.
Do not run the power cord in front of the product.
The product must only be connected to a correctly installed and earthed power point. Check that the mains voltage corresponds to the rated voltage on the type plate.
Make sure to plug the plug firmly in the power point. Do not touch the power cord or the plug with wet hands.
Put the switch in the OFF position and pull out the plug when the product is not in use.
Do not route the power cord under carpets etc. Place the power cord so that there is no risk of treading on it, or tripping over it.
Do not expose children to the flow of air from the product for long periods.
Only use the product in a well ventilated area. Do not place the product near walls or corners, where incoming or outgoing air can be blocked. Do not put the product near curtains, or other flammable materials —fire risk.
Do not expose the product to vibrations, knocks or blows when in use.
Do not use the product in explosive environments, for example in the vicinity of flammable liquids, gas or dust. Do not place the product near a naked flame or other source of heat.
Do not attempt to dismantle or repair the product. Repairs should be carried out by qualified personnel or an authorised service centre.
A damaged cord or plug must be replaced by an authorised service centre or qualified person to ensure safe use.
Do not use aerosol spray, e.g. insect spray or other flammable spray, near the product.
Switch off the product immediately and pull out the plug in the event of any abnormal noise, smell, smoke or other sign of a problem.
Portable electric heating fans are intended for spot heating or as supplementary sources of heat. They are not intended to be used as the main heating system.

WARNING!

Some parts of the product get very hot — risk of burn injuries. Keep the product under careful supervision when it is used by, or near children or persons with functional disorders.
Do not put any foreign objects on the product.
Never poke your fingers or any other objects into the inlet or outlet openings.
Do not use the product near a bath, shower or swimming pool.
Do not cover the product, this can result in overheating.

SYMBOLS

Instruction Book Icon Read the instructions.
Safety Class II Icon Safety class II.
Do not Cover Do not cover.
Approved in accordance with the relevant directives.
Recycle discarded product in accordance with local regulations.

TECHNICAL DATA

Rated voltage: 230 V ˜50 Hz
Output: 1200/2000 W
Safety class: II
Temperature interval: 18 — 30°C
Size: 19.6 x 45.2 x 19.6 cm

DESCRIPTION

Control panel
Ceramic heating element
Foot with built-in tip-over protection
Power switch (on/off)
Temperature setting
Function setting
Timer
Oscillation mode

USE

BEFORE USE

Unpack the product and all the parts from the packaging and place them on a level surface as shown.
Check that the mains voltage corresponds to the rated voltage on the type plate. Plug in the plug. The product is now ready to use.

IMPORTANT:

Do not place the product near walls or corners, where incoming or outgoing air can be blocked.
Do not place the product directly below a power outlet.

START

Start the product by pressing the on/off button (4) on the control panel. The product starts in full power mode and the status light for full power goes on.

NOTE:

The first time the product is used it may emit some fumes or smell. This is quite normal and is because the heating element has a protective coating from the manufacturing. This coating quickly vapourises and any vapour and smell disappear.

FUNCTION SETTINGS

Switch between the different functions by pressing repeatedly on the function selector button (6) on the control panel: normal mode, low → energy saving mode ECO → normal mode, full power.

TEMPERATURE SETTING

Start the product and then tap the temperature setting button (5) on the control panel to set the required temperature (set point temperature). The temperature interval can be set from 18 to 30°C. When the room temperature (actual temperature) reaches the set temperature (set point temperature) the heating switches off and the power level indicator flashes for 15 seconds and then returns to normal mode. When the room temperature drops below the set temperature the heating starts again.

TIMER FUNCTION

Timed start

To set start from 0 to 7 hours, tap the timer button on the control panel when the product is in standby mode.

Timed switching off

To set switching off from 0 to 7 hours, tap the timer button on the control panel when the product is running.

OSCILLATION MODE

To start or switch off the oscillation function, tap the button for oscillation mode (8) when the product is running.

WARNING FOR CONDUCTOR FAULT/ SHORT CIRCUIT

If there is a conductor fault in the temperature sensor circuit the status light on the product will flash “1h” continuously, irrespective of the status of the product, and the buzzer will emit 10 long signals.
If there is a short circuit in the temperature sensor circuit the status light will flash “2 h” continuously and the buzzer will emit 10 long signals.

OVERHEATING PROTECTION

If the ambient temperature exceeds 50°C the product will switch off automatically.
The status lights “1h”, “2h” and “4h” flash continuously and the buzzer emits 10 long Signals if any button is pressed. When the ambient temperature has dropped below 50°C the overheating protection can be reset by switching off the power supply and then connecting it again.

TIP-OVER PROTECTION

If the product tips over it will switch off automatically, the status lights “1h” and “2h” will flash continuously, and the buzzer emit 10 long signals. When the product is lifted up it must be switched off and then reset with the power switch button before it can be used asnormal again.

ENERGY SAVING MODE ECO

When starting the energy saving mode ECO the set point temperature is as standard set to 24°C. The product selects the power mode automatically on the basis of the difference between the room temperature (actual temperature) and the set temperature (set point temperature).

MAINTENANCE

NOTE:

Switch off the product, pull out the plug from the power point, and wait until the product has completely cooled before cleaning and/ or maintenance.

Wipe any dust off the product with a soft cloth. Clean the product when necessary with a cloth moistened with water and a mild detergent. Wipe dry with a soft, clean cloth.
The fan motor is permanently lubricated and does not need any further lubrication.
No further maintenance should be carried out by the user. Contact the retailer if additional maintenance or repairs are needed.

STORAGE

Pull out the plug and cover over the product to protect it from dust if it is not going to be used for some time.
Store the product in a cool, dry and well ventilated place.

TROUBLESHOOTING

Carry out the checks and measures in the table in the event of malfunction. If normal functionality cannot be restored through the checks and measures in the table, or if the malfunction is not included in the table, contact the retailer.

Problem	Possible cause	Action
The product will not start, even though it is connected to a power point.	The
plug is not properly plugged in.	Check that the plug is correctly inserted,