anslut 013371 Speed Control Instruction Manual

013371 Speed Control
Instruction Manual

OPERATING INSTRUCTIONS

An Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)

Care for the environment!
Must not be discarded with household waste! This product contains electrical or electronic components that should be recycled Leave the product for recycling at the designated station e.g. the local authority’s recycling station
Jula reserves the right to make changes. In the event of
problems, please contact our customer service www.Jula.com

For the latest version of operating instructions, see www.jula.com
2021-02 10
0Jula AB

SAFETY INSTRUCTIONS

Read the instructions carefully before use and save them for future reference.

• Only persons authorized to install electrical units up to 1000 V must carry out maintenance and installation.
• All the circuits in the speed control are live. Maintenance and installation must only be carried out after disconnecting the mains voltage.
• It is prohibited to
  – Use the speed control if there are any signs of damage to the casing or contacts.
  – To use the speed control if moisture or water has penetrated the casing
  – To use the speed control in rooms with explosive or corrosive substances in the air.
  – To use the speed control near heating elements.

NOTE:
Only use the special screwdriver that comes with the product.
BILD 1
SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded products in accordance with local regulations.

TECHNICAL DATA

INSTALLATION

• The speed control must be installed indoors and vertically on the wall.
• The connection to the mains must have a residual current device.
• Do as follows to connect the speed control to the mains:

1. Remove the dial from the speed control (7)

2. Undo the nut (2) and remove the cover and frame (3)

3. Remove the screws (4) that fix the speed control in the box fitting and remove the speed control (5) from the box.

4. Put the cables in the box fitting (6)
   FIG. 2

5. Put the box fitting on the wall.

6. Strip the ends of the cables about 6-7mm.

7. Connect the cables to the terminal block (7) on the speed control (P) and the fan (B) as per the wiring diagram and the label on the terminal block.
   FIG. 3
   FIG. 4

8. Put the speed control in the box fitting and fasten it with the screws.

To ensure normal operation as intended the speed control must be regulated for minimal rotation speed:

1. Turn the dial anticlockwise while the control is in switched on mode (without the dial clicking and switching off)
2. Connect the power.
3. Use a Phillips screwdriver with an insulated handle to turn the potentiometer (8) until a minimal rotation speed is achieved.
4. Turn the dial anticlockwise to the off position (so that clicking noise is heard). Wait for the rotation of the fan to stop.
5. Turn the dial to minimal fan speed and it is now adjusted for a stable minimal rotation speed.
6. Fit the frame and tighten the nut
7. Fit the dial.

NOTE:
The speed control must not be used if the minimal rotation speed is not set correctly.
The fan can be damaged if the minimal rotation speed is not correct.

TROUBLESHOOTING

The speed control should work immediately after it has been connected to the mains.
Carry out troubleshooting according to the table if the speed control does not work.

the speed control is correctly connected.
Defective fuse.| Replace the fuse.
The fan does not work even though the speed control is switched on.| Incorrect setting of minimal rotation speed.| Adjust minimal rotation speed.

Item no. 013371

Documents / Resources

| anslut 013371 Speed Control [pdf] Instruction Manual
013371, Speed Control
---|---
| anslut 013371 Speed Control [pdf] Instruction Manual
013371, Speed Control, 013371, Control

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>