Guanyu GY-Z6C Wireless Charger User Manual

Guanyu GY-Z6C Wireless Charger

Notice : To ensure charging 3 safely and efficiently, you must use 9V/2A adapter and quick charge cable, if including lSWfast charging phones, you must use 9V/2.7Aor 12V/2A adapter and quick charge cable (if not use the appropriate adapter and quick charge cable, the charger may not charge phone fast, or may not charge 3 devices simultaneously, or damage the charger)

Product Appearance

Operation Steps

1.  Connect the cha「ger to a 9V/2A,9V/2. 7 A or 12V/2A ada pie「through a Type-Chargable  cable to switch on the power;
2. Put your phone on then charge;
3. Put the apple watch on and suck ,t up to charge (roll the watch band to minmize to charge better)
4.  Plug your earphone case ,n the connector to charge.

LED light instructions

• Greenlight is on: Standby mode or not charging the phone
• Bluelight is breathing: Wireless chatting the phone
•  Blue andGreenlightflash Foreign body is detected or the phone is misaligned (the phone charging will automatically stop)

Charging Schematic Diagram

Applicable Devices

Smart Phone Apple: ;Phone 12,12 Pro,12 Pro Max,12 m;n;,sE,11,11 Pro,11 Pro Max,Xs,Xs Max,XR,X,8,8 Plus, Samsung: Galaxy S: 20 5G,20+ 5G,20 Ultra 5G,10,10+,10e,9,9+,8,8+,7,7 edge,6,6 edge,6 edge+, 6 G9209,6 Active; Galaxy Note:20,20 Ultra 5G,10,1De,10+,9,8,7,6,5, LG: G2(VS9BO,Verizon version),G3,G6,G6+,G7,G7 Thin Q,G7+ ThinQ,GB,GB ThinQ,V30,V30+,V35, V40 ThinQ,V50,V507hin Q, LG Lucid2 (VS870),LG Optimus F5 (As870),LG Optimus Vu 3,
Spectrum 2,0ptimus G Pro, Optimus Vu II, Optimus LTE2,etc MOTOROLA: Droid Turbo, Droid Turbo2,Droid 5,Moto Maxx,Ultra M, MotoX Force Huawei:P40 Pro,P40 Pro+,P30 Pro; Mate:40 RS,40 Pro,40 Pro+,30 5G, 30 Pro 5G, 30, 30 Pro, 30 RS, 20 Pro, 20 RS, RS; Xiaomi: 10,10 Pro,9,9 Pro, Mix3,Mix 2s; Including other devices with wireless charging receiver built-in; other some devices need to add a wireless charging receiver
( Note : All devices must meet the Qi standard)

Product Specification

Input: 9V/2A,9V/2.7Aorl2V/2A (must use 9V/2.7A or 12V/2A when charging 3 devices including

• Phone Output: 15W/10W/7.5W/5W
• Watch Output: 2.5W (Apple iWatch Sl,S2,S3,S4,S5,S6,SE)
• Earphone Output: 2_ow Lightning (Apple AirPods 1, 2,AirPods Pro)
• Input Interface: Type-C port
• Transmission Distance(Phone):’s8mm
• Conversion Rate(Phone):,>73%
• Product Size:142X70Xl8. 7mm

Accessories List

Wireless Charger·1. Type-C quick charge cab1e·1, Use manua1·1

Attention

1. Please keep the charger away from water or other liquid;
2. IF you need to clean the charger,please make sure it is not connected power supply,
3.  Using Environment temperature remains 0-45’C
4. Charging environment of smart phone will not

Answer questions

1.  lf you’re experiencing interrupted or slow charging, check the following:
2.  The back of you「 phone shou Id not have any meta I, pop sockets, or credit cards
3.  Put the phone in the center of the charging surf ace (this lets the charging coil in youR phone
4.  The wireless charging coil on Sony phones is located slightly below center
5.  Phone cases should be no thicker than 5 mm for effective charging.
6. Check whether the adapter is QC3.0 fast charger
7.  lf you’refalling to charge your device, please try out the following
8.  Please restart yourcell phone and test with other USB cable
9.  Please check whetherthe indicator turns on or not.
10. Please check the Adapter is QC3.0 Quick Charge Output:9V /2A) or not, iPhone original adapter does not match the wireless charger.
11.  Please checkyou Phone case thickness(<=Smm). Metal ring or Magnetic Pad with not be available.
12.  lf you’re using the recommended wireless charger with the QC3.0 Adapter and have removed any potential charging obstructions, but are still experiencing issues, try:
13.  Replacing the cable connectingyour the wireless charger
14.  Rebooting your phone.
15.  Unplugthe adapter and reinsert

FCC Statement

This device complies with part 15 FCC Rules. Operation is Subject To the following two conditions:

1.  This device may not cause harmful interference, and
2.  this devicemust accept any interference received, including interference that may cause undesired operation.

Changes or modifications not explicitly approved by the partyresponsible for compliance could void the user’s authority tooperate this equipment.
Note : this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC radiation exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>