OBSIDIAN NETRON RDM645 Control System Installation Guide

June 5, 2024
OBSIDIAN

OBSIDIAN NETRON RDM645 Control System - LOGOOBSIDIAN NETRON RDM645 Control SystemOBSIDIAN NETRON RDM645 Control System - LOGO
2 Installation Guide

©2021 OBSIDIAN CONTROL SYSTEM S all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. Obsidian Control Systems logo and identifying product names and numbers herein are trademarks of ADJ PRODUCTS LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non- ADJ brands and product names are trademarks or registered trademarks of their respective companies.

OBSIDIAN CONTROL SYSTEMS and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

ELATION PROFESSIONAL B.V.
Junostraat 2 | 6468 EW Kerkrade, The Netherlands
+31 45 546 85 66

Art-Net
This device incorporates Art-Net™, Designed by and Copyright Artistic License Holdings Ltd.

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

  • Reorient or relocate the device.
  • Increase the separation between the device and the receiver.
  • Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to helping to protect the environment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use.
Thank you!

Document Version: An updated version of this document may be available online. Please check www.obsidiancokontrol.com for the latest revision/update of this document before beginning installation and use.

Date Document Version Note
10/29/19 1 Initial release.
11/26/19 1.5 Update specifications
12/27/19 2.0 Added Art-Net Copyright
01/02/20 2.5 Updated Silkscreen
09/21/20 3.0 Update Specifications
02/09/21 3.5 Updated Silkscreen

GENERAL INFORMATION

INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use information.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all accessories necessary to install and operate the device have arrived intact. In the event, that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this device to your dealer without first contacting customer support. Please do not discard the shipping carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT
Contact your local Obsidian Controls Systems dealer or distributor for any product-related service and support needs. Also visit forum.obsidiancontrol.com with questions, comments, or suggestions.
OBSIDIAN CONTROL SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET +31 45 546 85 63 | support@obsidiancontrol.com
OBSIDIAN CONTROL SERVICE USA – Monday – Friday 08:30 to 17:00 PST 866-245-6726 | support@obsidiancontrol.com

LIMITED WARRANTY

  1. Obsidian Control Systems hereby warrants, to the original purchaser, Obsidian Control Systems products to be free of manufacturing defects in material and workmanship for a period of two years (730 days).
  2. For warranty service, send the product only to the Obsidian Control Systems service center. All shipping charges must be pre-paid. If the requested repairs or services (including parts replacement) are within the terms of this warranty, Obsidian Control Systems will pay return shipping charges only to a designated point within the United States. If any product is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product. If any accessories are shipped with the product, Obsidian Control Systems shall have no liability whatsoever for loss and/or damage to any such accessories, nor for the safe return thereof.
  3. This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in any manner that Obsidian Control Systems concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Obsidian Control Systems factory unless prior written authorization was issued to purchaser by Obsidian Control Systems; if the product is damaged because not properly maintained as set forth in the product instructions, guidelines and/or user manual.
  4. This is not a service contract, and this warranty does not include any maintenance, cleaning, or periodic check-up. During the periods specified above, Obsidian Control Systems will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Obsidian Control Systems under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Obsidian Control Systems. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
  5. Obsidian Control Systems reserves the right to make changes in design and/or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
  6. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied warranties made by Obsidian Control Systems in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Obsidian Control  Systems be liable for any loss and/or damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product.
  7. This warranty is the only written warranty applicable to Obsidian Control Systems products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
  8. Use of software and firmware:
    To the maximum extent permitted by applicable law, in no event shall Elation or Obsidian Control Systems or its suppliers be liable for any damages whatsoever (including, but not limited to, damages for loss of profits or data, for business interruption, for personal injury or other loss whatsoever) arising out of or in any way related to the use of or inability to use firmware or software, the provision of or failure to provide support or other services, information, firmware, software, and related content through the software or otherwise arising out of the use of any software or firmware, even in the event of the fault, tort (including negligence), misrepresentation, strict liability, breach of warranty of Elation or Obsidian Control Systems or any supplier, and even if Elation or Obsidian Control Systems or any supplier has been advised of the possibility of such damages.

WARRANTY RETURNS: All returned service items, whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem, as well as the R.A. number, must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without an R.A. number clearly marked on the outside of the package will be refused and returned at the customer’s expense. You may obtain an R.A. number by contacting customer support.

SAFETY GUIDELINES

This device is a sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow all instructions and guidelines in this manual.  OBSIDIAN CONTROL SYSTEMS is not responsible for injury and/or damages resulting from the misuse of this device due to the disregard of the information printed in this manual. Only the original included parts and/or accessories for this device should be used. Any modifications to the device, included and/or accessories will void the original manufactures warranty and increase the risk of damage and/or personal injury.

OBSIDIAN NETRON RDM645 Control System - FIG 1PROTECTION CLASS 1 – THE DEVICE MUST BE PROPERLY GROUNDED
DO NOT ATTEMPT TO USE THIS DEVICE WITHOUT BEING FULLY TRAINED ON HOW TO USE IT. ANY
DAMAGES OR REPAIRS TO THIS DEVICE OR ANY LIGHTING FIXTURES CONTROLLED BY THIS DEVICE
RESULTING FROM IMPROPER USE, AND/OR THE DISREGARD OF THE SAFETY AND OPERATION
GUIDELINES IN THIS DOCUMENT VOID THE OBSIDIAN CONTROL SYSTEMS WARRANTY, AND ARE NOT
SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS, AND MAY ALSO VOID THE WARRANTY FOR ANY
NON-OBSIDIAN CONTROL SYSTEMS DEVICES.
KEEP FLAMMABLE MATERIALS AWAY FROM THE DEVICE.
DRY LOCATIONS USE ONLY!
DO NOT EXPOSE THE DEVICE TO RAIN, MOISTURE, AND/OR SEVERE ENVIRONMENTS!
DO NOT SPILL WATER AND/OR LIQUIDS ON OR INTO THE DEVICE!

DISCONNECT the device from AC power before removing fuses or any part, and when not in use. Always electrically ground this device. Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault protection. Do not expose the device to rain or moisture. Never attempt to bypass fuses. Always replace defective fuses with ones of the specified type and rating. Refer all services to a qualified technician. Do not modify the device or install other than genuine Netron parts.
CAUTION: Risk of Fire and Electrical Shock. Use only in dry locations.
CAUTION: Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to local environmental regulations.
AVOID brute force handling when transporting or operating.
DO NOT expose any part of the device to open flame or smoke. Keep devices away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
DO NOT use devices in extreme and/or severe environments. Replace fuses with ones of the same type and rating only. Never attempt to bypass a fuse. The unit is provided with a single fuse on the Lineside.
DO NOT operate the device if the power cord is frayed, crimped, damaged, and/or if any of the power cord connectors are damaged, and does not insert into the device securely with ease. NEVER force a power cord connector into the device. If the power cord or any of its connectors is damaged, replace it immediately with a new one of a similar power rating. Strictly use a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection. Use only the provided AC power supply and power cords and the correct connector for the country of operation. Use of the factory-provided power cable is mandatory for operation in the US and Canada. Allow free unobstructed airflow to the bottom and back of the product. Do not block the ventilation slots. Operate the console only on a stable and solid surface.
DO NOT use the product if the ambient temperature exceeds 40°C (104° F) Transport the product only in suitable packaging or a custom-fitted road case. Transportation damage is not covered under warranty.
CAUTION: Risk of explosion if CMOS battery is replaced by an incorrect type. Dispose of used batteries according to local environmental regulations.
CAUTION: Do not expose the CMOS battery to excessive heat such as sun or fire.

OVERVIEW

KEY FEATURES: RDM6XL
The Netron RDM6XL is a rugged and compact DMX/RDM Splitter. Designed for live production and installations, it features six opto-isolated 5pin XLR outputs and flexible mounting options to cover any situation.

  • (6) XLR 5pin outputs
  • DMX and RDM compliant
  • Optically isolated ports
  • Power / DMX Through connectors
  • Powder-coated aluminum ½ rack housing

KEY FEATURES: RDM645
The Netron RDM645 is a rugged and compact DMX/RDM Splitter. Designed for live production and installations, it features six opto-isolated RJ45 DMX outputs and flexible mounting options to cover any situation.

  • (6) Locking RJ45 Ethernet DMX outputs
  • DMX and RDM compliant
  • Optically isolated ports
  • Power / DMX Through connectors
  • Powder-coated aluminum ½ rack housing

INSTALLATION INSTRUCTIONS

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or installations.

USE CAUTION WHEN POWER LINKING OTHER MODEL DEVICES AS THE POWER CONSUMPTION OF OTHER MODEL DEVICES MAY EXCEED THE MAXIMUM POWER OUTPUT OF THIS DEVICE. CHECK SILKSCREEN FOR  MAXIMUM AMPS.
The device MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS DEVICE IN A SUSPENDED ENVIRONMENT TO ENSURE THE DEVICE WILL NOT DROP IF THE CLAMP FAILS. Overhead device installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable that can hold 10 times the weight of the device.

POWER LINKING
USE CAUTION WHEN POWER LINKING AS THE POWER CONSUMPTION MAY EXCEED THE MAXIMUM POWER OUTPUT ON THIS DEVICE. CHECK SILKSCREEN FOR MAXIMUM AMPS.

INSTALLATION INSTRUCTIONS

Installation Options:

  • Standalone, where either device sits on a firm flat surface.
  • Truss-mounted using the M10 or M12 mounting holes for use with a truss clamp or appropriate mounting hardware.
  • Wall-mounted horizontally or vertically (brackets included)
  • DIN Rail mounted horizontally or vertically (adapter included)
  • Rack-mount option for two devices (requires NET Shelf, not included)

OBSIDIAN NETRON RDM645 Control System - FIG 3

CONNECTIONS

AC CONNECTIONS
The Obsidian Control Systems Netron RDM6XL and RDM645 are rated 100-240V 47/63Hz and accept AC mains power over a range of 90-264V 47/63Hz. Do not connect it to power outside this range. Damage resulting from the incorrect connection is not covered under warranty.

North America: A cable with a NEMA 15-5P plug is provided for use with the RDM6XL and RDM645 in the USA and Canada. This approved cable must be used in North America.

Rest of the world: The provided True1 cable is not fitted with a country- specific plug. Install only a plug that meets local and or national electrical codes and is suitable for the country’s specific requirements.

A 3-prong grounded-type (earthed type) plug must be installed following the plug manufacturer’s instructions. To apply power to the product: In addition to the input, the unit has a loop through an IEC output connection, allowing daisy-chaining between multiple RDM6XLs and RDM645s. Do not exceed the 6A total power draw from the IEC output.

DMX CONNECTIONS: RDM6XL
All DMX Output connections are 5pin female XLR; however, the pin-out on all sockets is pin 1 to shield, pin 2 to cold (), and pin 3 to hot (+). Pins 4 and 5 are not used.
Carefully connect DMX cables to the respective ports.
To prevent damaging the DMX ports, provide strain relief and support. Avoid connecting FOH Snakes to the ports directly.

Pin Connection
1 Com
2 Data –
3 Data +
4 Not connected
5 Not connected

OBSIDIAN NETRON RDM645 Control System - FIG 4

DMX CONNECTIONS: RDM645
All DMX Output connections are RJ45 (see chart below).
Carefully connect DMX configured RJ45 cables to their respective ports.
To prevent damaging the RJ45 ports, provide strain relief and support. Avoid connecting FOH Snakes to the ports directly.

L Connection
1 Data
2 Data
3 Not connected
4 Not connected
5 Not connected
6 Not connected
7 Com
8 Com
Shield Earth

OBSIDIAN NETRON RDM645 Control System - FIG 5

**CONNECTIONS: RDM6XL (FRONT & REAR PANELS)

**

FRONT CONNECTIONS

  • 5Pin DMX Input
  • (6) 5Pin Opto-Isolated DMX Outputs
  • RDM Enable

OBSIDIAN NETRON RDM645 Control System - FIG 6

DMX PORTS STATUS INDICATOR LEDs

LED Color Solid Blink Flashing/Strobing
DMX PORTS BLUE DMX Out Stable Slow On/Off Blink Flash on RDM Packets
DMX Lost Active RDM communication

REAR CONNECTIONS

  • 5pin DMX Input (parallel with front)
  • 5pin DMX Through
  • Terminate
  • Power In/Through

OBSIDIAN NETRON RDM645 Control System - FIG 7

CONNECTIONS: RDM645 (FRONT & REAR PANELS)

FRONT CONNECTIONS

  • Locking RJ45 Ethernet DMX Input
  • (6) Locking RJ45 Ethernet Opto-Isolated DMX Outputs
  • RDM Enable

OBSIDIAN NETRON RDM645 Control System - FIG 8

DMX PORTS STATUS INDICATOR LEDs

LED Color Solid Blink Flashing/Strobing
DMX PORTS BLUE DMX Out Stable Slow On/Off Blink Flash on RDM Packets
DMX Lost Active RDM communication

REAR CONNECTIONS

  • Locking RJ45 Ethernet DMX Input (parallel with the front)
  • Locking RJ45 Ethernet DMX Through
  • Terminate
  • Power In/Through

OBSIDIAN NETRON RDM645 Control System - FIG 9

MAINTENANCE

The Obsidian Control Systems Netron RDM6XL and RDM645 are designed as rugged, roadworthy devices. The only required service is occasional cleaning. For other service-related concerns, please contact your Obsidian Control Systems dealer, or visit www.obsidiancontrol.com.

Any service that is not described in this guide must be carried out by a trained and qualified Obsidian Control Systems technician.
Like with any electronic device, the RDM6XL and RDM645 require periodic cleaning. The schedule relies on the environment in which the device is operated. An Obsidian Control Systems technician can provide recommendations if necessary.

Never spray cleaner directly onto the device surface; always spray into a lint-free cloth and wipe it clean. Consider using cleaning products designed for cellphone and tablet devices.

Important! Excessive dust, dirt, smoke, fluid build-up, and other materials can degrade the performance of the RDM6XL and RDM645 devices, causing overheating and damage to the unit that is not covered by the warranty.

Fuse Replacement:
Single fuse in the Lineside; the RDM6XL and RDM645 are protected by a single 1A slow-blow mains fuse in a fuse holder on the back of the device.
Disconnect the product from AC mains power before replacing the fuse as parts of the product may remain life even if the mains fuse has blown.

SPECIFICATIONS

RDM6XL RDM645

Mounting Hardware
– Standalone
– Truss-mount (M10 or M12 mounting hole)
– Wall-mount horizontal or vertical (included)
– DIN Rail horizontal or vertical (included)
– Rack-mount option (requires NET Shelf)| Mounting Hardware
– Standalone
– Truss-mount (M10 or M12 mounting hole)
– Wall-mount horizontal or vertical (included)
– DIN Rail horizontal or vertical (included)
– Rack-mount option (requires NET Shelf)
Connections| Connections
Front
– DMX Input
– (6) 5pin Opto-Isolated DMX Outputs
– RDM Enable| Front
– Locking RJ45 Ethernet DMX Input
– (6) Locking RJ45 Ethernet Opto-Isolated DMX Outputs
– RDM Enable
Back
– 5pin DMX Input (parallel with the front)
– 5pin DMX Through
– Terminate
– Power In/Thru| Back
– Locking RJ45 Ethernet DMX Input (parallel with the front)
– Locking RJ45 Ethernet DMX Through
– Terminate
– Power In/Thru
Physical
– Length: 8.5” (215mm)
– Width: 5.5” (139mm)
– Height: 1.65” (42mm)
– Weight: 1 kg (2.2 lbs)| Physical
– Length: 8.5” (215mm)
– Width: 5.5” (139mm)
– Height: 1.65” (42mm)
– Weight: 1 kg (2.2 lbs)
Electrical
– 100-240 V nominal, 47/63 Hz, 10W| Electrical
– 100-240 V nominal, 47/63 Hz, 10W
Included Items
– 1.5m power cable (EU or US version)
– (2) Wallmount plates
– (2) DIN-Rail clamps| Included Items
– 1.5m power cable (EU or US version)
– (2) Wallmount plates
– (2) DIN-Rail clamps

DIMENSIONS: RDM6XL

OBSIDIAN NETRON RDM645 Control System - FIG 10 DIMENSIONS: RDM645OBSIDIAN NETRON RDM645 Control
System - FIG 11 DIMENSIONS NETSHELF (NOT INCLUDED)

OBSIDIAN NETRON RDM645 Control System - FIG 12 OPTIONAL ACCESSORIES

ORDER CODE ITEM
US#: NRE001 / EU#:1330000060 NET Shelf (rackmount shelf)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals