camry CR 1142 Bluetooth Speaker User Manual

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE

READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different if the device is used for commercial purposes.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
3. The applicable voltage is 230V, ~50Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
4. Please be cautious when using children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7. Never put the power cable, the plug or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc.. Never use the product in humid conditions.
8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
9. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
11. Never use the product close to combustibles.
12. Do not let the cord hang over the edge of a counter or touch hot surfaces.
13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
14. In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.

DESCRIPTION OF THE DEVICE

1. Power switch
2. Charging input
3. Charging LED
4. Signalizing LED
5. The external device input AUX

BATTERY CHARGING
Before first use, charge the batteries.

1. Connect the micro-USB plug into the charging input (2), and the USB plug into the socket on your computer or USB charger.
   NOTE: Charging input (2) is used solely to charge the battery!

2. Charging LED (3) will shine all the charging time. After charging, the LED goes out.

USING THE DEVICE

1. You can switch on and off the device using switch (1). After switching on of device signalizing LED (4) will flash.
2. Activate the Bluetooth mode on your external device and select a device called CR 1142. If necessary, enter the password “0000”.
3. The speaker will connect to an external device. The LED (4) will stop flashing. You can start playback on the external device.
4. The sound volume can be adjusted on the external device.
5. The speaker can be connected to an external device also using a cable with a 3.5 mm jack plug. Then the signalizing LED (4) does not work.

SPECIFICATIONS:

Input Voltage: 5V 1A
RMS power: 3W Bluetooth: v2.0 (2,5mW)

To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliance should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.

Adler Sp. z o.o. Ordona 2a, 01-237 Warsaw, Poland hereby declares that the CR 1172 device complies with the Directive 2014/53 / EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.adler.com.pl/dane/deklaracje/

References

• Index of /dane/deklaracje

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>