miroir MR-IH001 Baby Monitor User Guide
- June 6, 2024
- Miroir
Table of Contents
- miroir MR-IH001 Baby Monitor User Guide
- SAFETY INSTRUCTIONS
- CAUTION
- PACKAGE CONTENTS
- PRODUCT DIAGRAM
- Baby Monitor
- Camera
- GETTING STARTED
- 3. Pairing the Baby Monitor & the Camera
- 4. Placing the Camera
- 5. Wall Mounting Camera
- 6. Wide-Angle Lens (Optional)
- FUNCTIONS & OPERATIONS
- Monitor Interface Overview
- Top Status Indications
- Bottom Menu Brief
- 1. Volume Adjustment
- 2. Display Brightness Adjustment
- 3. Talkback
- 4. Monitor Settings
- 6. Digital Zoom & Circulating
- 7. Pan-n-Tilt
- 8. Night Vision
- 9.Alarm
- 10. Wide-angle Viewing (Optional)
- 11. Temperature Alert
- SPECIFICATIONS
- Camera
- TROUBLESHOOTING
- WARRANTY & CUSTOMER SERVICE
- FCC STATEMENT
- FCC 20cm Statement
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
miroir MR-IH001 Baby Monitor User Guide
SAFETY INSTRUCTIONS
Keep cord out of the reach of children (more than 3ft / 0.9m away) in case of STRANGULATION.
- NEVER place the camera or cord in or near the crib or playpen.
- NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.
- Only use the AC adapters provided.
- Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
- Only use attachments and accessories specified by the manufacturer.
- Unplug this device when unused for long periods of time.
- Do not insert anything into the upgrade pinholes. This operation is only intended for professionals.
CAUTION
- NOT toys. Do not allow children to play with them.
- The lens and lens hood are small parts, keep them out of your baby’s reach at all times.
- This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
- This product is not intended for use as a medical camera and its use should not replace adult supervision.
- Unplug the product during lightning storms.
- Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that.
- Check the reception regularly. Test the camera before use and after changing the camera’s location.
- For indoor use only.
- Clean the camera with a dry cloth only.
- Do not block any ventilation openings.
- Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
PACKAGE CONTENTS
Baby Monitor & Camera (Model: MR-IH00l)
- Monitor Adapter with USB-C Charging Cable
- Camera Adapter
- Micro-USB Charging Cable
- Quick Start Guide
- User Guide
PRODUCT DIAGRAM
Baby Monitor
- Antenna
- Volume Indicators
- Microphone
- Charging Indicator
- Power Indicator
- Menu Button
- Zoom Button
- Left Button
- Up Button….
- Right Button
- OK Button
- Down Button
- Talk/ Shortcut Button
- Power Button
- Upgrade Pinholes
- Back Stand
- Speaker
- USB-C Port
Camera
- Camera Vents
- Camera Antenna
- Micra-USB Port
- Temperature Sensor
- Reset Pinhole
- Power Switch
- Speaker
- Lens
- Pairing Button
- Mounting Hole
GETTING STARTED
1. Charging & Powering Baby Monitor
- Connect the monitor odopter to the monitor ond o power outlet.
- Unplug the unit when its power indicotor turns off, indicoting a full charge.
- Press the Power button on the monitor to power on with the power indicator lighting green.
2. Powering Camera
- Connect the camera to power source via the Micro-USB cable and camera adapter.
- Slide the Power Switch on camera to power on. Make sure the power indicator light is green.
· Only use the power adapters included in the package.
- Do not place the camera and power cord within the reach of your baby.
3. Pairing the Baby Monitor & the Camera
By default, one camera has been paired with the monitor when manufactured.
When you power on the monitor and camera, the two will automatically pair.
To add more cameras, press the Pair Button at the bottom of the camera,
press Menu button, select through i -> @->+.and then the monitor will auto-
pair with the camera.
· Once they’re paired successfully, the camera number with icon 521 will be shown at the top left.
- Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
- t is recommended to pair in the baby’s room, or wherever you intend to place the camera.
4. Placing the Camera
Place the camera 1.5-2m / 4.9-6.6ft away from your baby for safety reason and for a better view when in night vision mode.
5. Wall Mounting Camera
- Select the spot to mount the camera, keeping it beyond your baby’s reach.
- Insert the screw (not included) pre-installed on wall into the mounting hole of the camera.
It’s strongly recommended to use a screw and screw anchor. Don’t release the camera until you’re sure it is firmly mounted.
6. Wide-Angle Lens (Optional)
The aluminum lens hood (no special video effects) has been installed when the
camera was manufactured.
To install wide-angle lens (sold separately), simply rotate the original lens
hood counterclockwise to remove. Then install the new lens and rotate
clockwise to fix in place.
FUNCTIONS & OPERATIONS
Monitor Interface Overview
Top Status Indications
Bottom Menu Brief
1. Volume Adjustment
- Use Shortcut Button: Press Talk Button ->Left/ Right Button to quickly adjust the volume with ) & Ill>) >i cons.
- Or you con press Menu Button -> OK Button ->Left/ Right Button to volume down/ up, and OK Button to saving your settings.
For system sound adjustment, please go to Monitor Settings -> ft Y System sound volume.
2. Display Brightness Adjustment
- Use Shortcut Button: Press Talk Button -> Up/ Down Button to quickly adjust the brightness with ~ & :.. icons.
- Or you can press Menu Butt~n _;·OK Button -> Up/ Down Button to turn up/ down the brightness, ond OK Button to saving your settings.
3. Talkback
- Press Talk/ Shortcut Button once to quickly a dust the Volume or Brightness.
- Press and hold Talk Button to talk to your baby, release it to exit the talking mode.
- When you enter the talking mode, the icon f will be shown on the monitor.
- When it’s mute or the speaker volume is too low, you may not be able to hear the baby.
- When you’re pressing the Talk Button, the camera will not transfer the sound to the monitor. Please release the button to listen to your baby.
4. Monitor Settings
Press Menu Button, Left and Right Buttons, and then OK Button to set the monitor:
- (9 Time setting: Set the current time by setting hour, minute, and AM/ PM.
- fr System sound volume: Select between Low, High, and Mute.
- I= Temperature scale: Select between °C and °F.
- c;zj Screen auto-sleep time: Select between lmin, 2min, 5min, and OFF.
- Restore to factory settings: Press OK Button to confirm resetting; “Restoring factory settings” will be shown when restoring, and you can’t press any button to control the device during this period. The monitor will auto restart when it’s done.
- Customer service contacts: Check the email, Tel. number, and address for customer service.
- To mute the sound during poor monitor-camera connection, please set the ti system sound volume to mute.
- When the monitor screen is under sleep mode, the power indicator flashes green slowly while the audio is still on; press any button to awake. You can also short press the Power Button to tum the screen off.
- Press and hold the Power Button to power on/ off the monitor.
5. Add /View/ Delete a Camera
-
Press Menu button, select through I->@->+ to add a camera.
-
Select through I-> 0 to view a camera.
· If there are 2 or more cameras, tap 10to cycle through the added cameras every 15 seconds.
· Select the camera number (1/2/3/4) to view the corresponding camera. -
Select through I -> iitto delete a camera. At least one camera shall be added. Do not delete all the cameras. If necessary, please add a new camera before deletion.
You can switch viewing different cameras; the current camera number will be shown with the Camera icon II on the monitor. You can only select one camera to view at one t ime.
6. Digital Zoom & Circulating
Press Zoom Button to zaom in to 2X / 4X when viewing the camera. A third
pressing of the button will restore to the original image. Press and hold OK
Button 4 seconds to start auto circulating, press OK
again to stop.
The current zoom level number will be shown with the Zoom icon Qz on the monitor.
7. Pan-n-Tilt
When viewing the camera, press Left/ Right/ Up/ Down Button to view at different angles, 108 degrees vertically and 270 degrees horizontally.
8. Night Vision
The night vision is automatically activated in a dim environment. The camera
has 12 high-intensity infrared LEDs for picking up clear images in the dark.
Black and white images can be captured within 2m distance.
9.Alarm
Press Menu Button -> Right Button to locate Alarm menu -> OK Button ->
Up/ Down Button to select the timer setting. You can set a 2Hr, 4Hr or 6Hr
alarm, or set the hour and minute otherwise. When the alarm time is reached, a
beep will be heard. Press OK Button to stop; otherwise it’ll keep beeping for
30s, beeping again in lmin, stops after it’s alerted 3 times.
When the timer is set. the Alarm icon • will be shown on the monitor. Before setting, please check that the monitor t ime is your current time.
10. Wide-angle Viewing (Optional)
Install your wide-angle lens (separately sold) referring to the previous mounting wide-angle lens section. Now you can view the camera in a wider angle of about 170 degrees.
11. Temperature Alert
The monitor will prompt too high (>35°C / 95°F) and too low (<0°C / 32°F) temperatures with the “HH” and “LL’.’ icon, accompanied with a ~i & A- icon and a beep alert.
SPECIFICATIONS
Monitor
Camera
TROUBLESHOOTING
WARRANTY & CUSTOMER SERVICE
12 months warranty
Lifetime customer service (contacts on the monitor, and back cover of this
User Guide)
FCC STATEMENT
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>