BRESSER BR-S36 RGB Professional Multi Color LED Light Instruction Manual

BRESSER BR-S36 RGB Professional Multi Color LED Light Instruction Manual

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

www.bresser.de/PF004360

WARRANTY

www.bresser.de/warranty_terms

GENERAL WARNINGS

RISK OF PHYSICAL INJURY!

Do not use in the presence of children or animals. Store out of reach of children and animals.

DANGER OF MATERIAL DAMAGE!

Make sure that no one can trip over connection cables of the device.
The device could be knocked over.

Only use the recommended power cable or the recommended battery for the power supply!

The manufacturer assumes no liability for voltage damage caused by the use of an unsuitable voltage supply

DANGER OF AN ELECTRIC SHOCK!

This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the instructions. Otherwise there is a RISK of ELECTRIC SHOCK.
Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat. Check this device, cables and connections for damage before use.
Never attempt to operate a damaged device, or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.

RISK OF GLARE!

Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

FIRE/EXPLOSION HAZARD!

Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not shortcircuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
• Only use the recommended power adapter

IMPORTANT NOTE!

Never take the device apart. In the event of a defect, please contact your dealer. They will contact the Service Centre and can arrange the return of this device for repair if necessary.
Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation and before any maintenance and cleaning work. Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the mains supply.
To disconnect the unit from the mains, always pull the mains plug and never pull the cable!
Do not subject the device to excessive vibrations.

INFORMATION ABOUT THE PRODUCT

A “Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/F004360/CE/F004360_CE.pdf

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. To benefit from an extended voluntary guarantee period as stated on the gift box, registration on our website is required.

You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www. bresser.de/warranty_terms.

www.bresser.de/warranty_term

SCOPE OF DELIVERY (FIG. 1)

LED light (A), mains adapter with cable (B), remote control (C)

PARTS OVERVIEW

LED LIGHT (A)

1. LED panel

2. Locking screw (rocker joint)

3. Vent

4. Battery holder

5. MODE button

6. Channel button

7. U bracket

8. Fixing screw (tripod connection)

9. Tripod connection

10. LED display

11. DC connection socket

12. On/Off button

13. Adjustment knob and ‘DIMMER/COLOR’ button
    MAINS ADAPTER WITH CABLES (B)

14. Mains adapter with 2-pole connection socket (14a)

15. Voltage cable (permanently connected to mains adapter) with DC hollow plug (15a)

16. Power cord with 2-pol plug (16a) and Euro plug (16b)

17. Function light
    REMOTE CONTROL (C)

18. LCD display

19. Power button

20. button

    • Menu button
    • + button

21. Battery compartment

DISPLAY

• Screen display
• Value power for color temperature in K (Kelvin)
• Function light ‘COLOR’
• Function light ‘CCT/RGB’
• Function light ‘DIMMER’

POWER SUPPLY

USING MAINS ADAPTER (STANDARD)

1. Plug the 2-pole plug (16a) of the mains cable (16) into the connection socket (14a) on the power adapter (14).
2. Plug the DC hollow plug (15a) of the power cable (15) on the mains adapter (B/14) into the DC connection socket (11) on the LED light (B).
3. Plug the Euro plug (16b) of the mains cable (16) into the mains socket.

*USING V-MOUNT BATTERIES (optional)**

1.  Slide the fully charged batteries* (2 pieces of type NP-F750 or NP-F960) into the battery holder (4) from above so that the battery clicks into place.
2. To remove, slide the battery out of the holder in the opposite direction.

TURNING THE LED LIGHT ON

1. Establish the power supply for the device (insert battery or connect to mains voltage).
2. Press the on/off button (12) to switch on the device.
3. Press the on/off button (12) again to switch off the device

BRIGHTNESS ADJUSTMENT

1. Press the “DIMMER/COLOR” button (13).
2. When the corresponding function light “DIMMER” (28) lights up brightly, you can adjust the brightness by turning the adjustment knob (13).

COLOR TEMPERATURE ADJUSTMENT

1. Press the “DIMMER/COLOR” button (13).
2. If the corresponding function light “COLOR” (27) lights up brightly, you can set the color temperature (32 to 56 / corresponds to 3200K to 5600 K) by turning the adjustment knob (13).

ADJUSTING THE RGB COLORS

1.  Press the “MODE” button (5).
2. When the corresponding function light “CCT/RGB” (26) lights up brightly, you can set the desired RGB color (0 to 360) by turning the adjustment knob (13).

SETTING A CHANNEL

1. Press the Channel button (6).
2. The last set channel (0-99) flashes.
3. Set the desired channel (0 to 99) by turning the adjustment knob (13).
4. Finally, press the Channel button (6) to save the set channel.

REMOTE CONTROL

USING THE 2.4G REMOTE CONTROL

1. Press the on/off button (19) to switch on the device.
2. Long press the power button (19) to turn off the device.

SCROLL THROUGH THE MENU
Press the menu button (21) to scroll through the menu.
Press 1x = Display 10 “Brightness” 10 = 10%
press 2x = display 56 “color temperature” 56 = 5600K
Press 3x = display 01 “channel” 01 = 1
Choosing a channel

1. Press the menu button (21) three times to get to the channel menu.
2. Press + or – (20/22) to select the desired channel.
3. Press the menu button (21) to confirm your selection.

SWITCH LIGHT ON/OFF

1. By default, the light status of the selected channel is “OFF”.
2. Press the on/off button (19) to turn on the light.
3. Long press the on/off button (19) to turn off the light.

ADJUSTING THE BRIGHTNESS

1. By default, the brightness level is 10% when the device is turned on.
2. Press the + or – button (29/22) to increase or decrease the brightness.

SETTING THE COLOR TEMPERATURE

1. Press the menu button (21) to select the color temperature for the current channel.
2. Press + or – button (20/22) to choose the desired color temperature

ADJUSTING THE TILT ANGLE

1. Hold the light and slowly loosen the tilt pivot locking screw (2).
2. Bring the lamp head into the desired position and handtighten the locking screw (2) again.

MOUNTING ON A TRIPOD (optional)

1. Loosen the fastening screw (8) for the tripod connection (9) so far that the opening of the tripod connection is exposed.
2. Place the light with the opening of the tripod connection on the spigot adapter of a tripod and tighten the fastening screw.

DISPOSAL

Dispose of the packaging materials by type. Observe the current legal regulations when disposing of the device! Information on proper disposal can be obtained from municipal waste disposal service providers or the Environmental Agency

Do not dispose of electronic devices in the household waste! According to the European Directive 2002/96/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner.

According to the regulations for batteries and accumulators, disposal in normal household waste is expressly prohibited. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive.
Batteries that contain toxins are marked with a sign and a chemical symbol.

1.   Battery contains cadmium
2. Battery contains mercury
3. Battery contains lead

TECHNICAL DATA

Service

Please contact the service centre first for any questions regarding the product or claims, preferably by e-mail.
e-mail: service@bresseruk.com
*Telephone:** +44 1342 837 098
BRESSER UK Ltd
Customer Support
Suite G3, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom

Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way, Edenbridge,
Kent TN8 6HF, Great Britain

@BresserEurope

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER
• Bresser | Bresser BR-S36RGB Professionelle LED Multi-Farbleuchte | Expand Your Horizon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>