ANNKE I41GD Wireless IP Camera User Manual
- June 6, 2024
- ANNKE
Table of Contents
- Production Information
- Legal Disclaimer
- Regulatory Information
- EU Conformity Statement
- Safety Instruction
- What’s in the Box
- Product Introduction
- Basic Operations
- Remote Access
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ANNKE I41GD Wireless IP Camera
Please download ANN KE software & user manuals from our download center: https://www.annke.com/pages/download-center
Production Information
Thank you for purchasing our NVR! This manual is designed for the installation
and operation of this product.
You can get more information about the features and functions of this product
in details. Please read this manual carefully before using. Please contact us
if you have any questions.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS
BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC Conditions
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this quipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 20cm between the radiator & body.
EU Conformity Statement
This product and -if applicable -the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU(WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info
Safety Instruction
These instructions are intended to ensure that user can use the product
correctly to avoid danger or property loss. The precaution measure is divided
into [Warnings] and [Cautions].
Warnings: Serious injury or death may occur if any of the warnings are
neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
|
---|---
Warnings: Follow these safeguards to prevent serious injury or death.|
Cautions: Follow these precautions to prevent potential injury or material
damage.
Warnings
- Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
- In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
- Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100 to 240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
- Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
- Please make sure that the plug is firmly connected to the power socket.
- If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
What’s in the Box
Product Introduction
NVR:
Camera:
Connection Diagram
The Camera’s Antenna Direction
Note: Make sure the antenna is screwed tight.
Basic Operations
Power on the NVR & Security Cameras
Connect the NVR to a monitor or a TV and then connect the NVR and the cameras to an outlet. They will boot automatically.
Log into the System
After the system is launched, click “ OK ” to log in. (The default user
name is admin, no password.)
Setup Wizard
After the initial login, you will see the setup wizard on the screen, helping you comprehend & set up the system.
General Configuration
Setup [Time Zone] , [Date time] , [Sync Time] , [Date Format] , [Language].
Wireless Setup
Please confirm the wireless channel and region.
Note: The wireless channel and region need to be conform to the local
legislation.
If the wireless signal is not stable, please click “ Adaptive Channel ” to
improve the signal.
Network Configuration
Click “ Diagnose ” to do a quick check on the NVR’s network connection,
and then click “ Auto Config ” to match the network for the NVR.
HDD Setup
Check the HDD and then click “Format” to format the HDD.
Note: Formatting HDD will erase all data contained in the disk. Please be careful when formatting an HDD.
Download App
Please download and launch the app. Scan the QR code of the device to add the device.
Change the Password
Please change the password after you have logged into the system.
Right click the mouse. Choose [System Setup] – [System Admin] – [User] to
change the password.
Note: Please keep your password in mind. If you have forgotten your password, please click the mouse’ left and right buttons more than 6 times at a uniform speed.If there is any question, please contact our support team via support@annke.com.
Set up the Video Recording
By default, the system will record 24/7. If you want to change the video
recording mode, please re-configure the system.
Right click the mouse. Choose [System Setup] – [Record Setup] – [Reset] to
select the video recording mode and period.
Motion Detection Setup
In default, the motion detection is enabled 24/7 and for all areas. If you
want to change the motion detection mode, please re-configure the system.
Right click the mouse. Choose [System Setup] – [Channel Setup] – [Video
Detection] to select the sensitivity level, the motion detection period and
areas.
Note: Please choose the suitable motion detection areas, period and motion sensitivity level to reduce the false alarms.
Video Playback
Right click the mouse and then choose [Video Playback]. In default, the
system will playback today’s earliest videos (4 channels).
You can drag the video timeline to play back the videos or speed up the video
playback.
Choose the channel & time that you want to play back, and then click “Search”
to locate the videos in a specific time.
Video Backup
Right click the mouse. Choose [Video Backup] and then select the channel,
video recording mode and period. Click “ Search “.
The system will display the video files. Choose the video files that you need
and then click “ Backup “.
You will get a prompt to ask you to insert a USB drive. Please insert the USB
drive within 60 seconds. The system will back up the video files
automatically.
Please remove the USB drive after all the video files have been exported.
Email Alert Setup
Right click the mouse. Choose [System Setup] – [Network Setup] – [Email]
to set up the email alerts.
Please select SMTP provide and encryption type and then input the correct
sender, password, SMTP port and the recipient’s email address.
How to Use the Antenna Extension Cable
Remote Access
Before you access the NVR system remotely, make sure the NVR is connected to the Internet. You can refer to 3.3.3 to check the Internet status of the NVR.
Mobile Client Access
Step 1. Search “Annke Sight” on App Store or Google Play and then
download the app to your smartphone.
Step 2. Open the app, click “Register”.(Picture 1)
Step 3. Enter your email address, click “Confirm”, follow the prompts to
complete registration and login. (Picture 2)
Step 4. Click the “+” button.(Picture 3)
Step 5. Click “Kit”.(Picture 4)
Step 6. Click ” E-3 “, Scan the ID number on the device.(Picture 5,6)
Step 7. Enter your password and click “Complete”.(Picture 7)
Note: Device has no password by default.
Step 8. Now you can preview the device.(Picture 8,9)
Access the Security System via CMS
Step 1. Install “ Annke Sight ” client on your computer.
Step 2. Launch the client and log into your account ( The default user
name is admin, no password ). Click “Add” and then enter the ID, username,
password, the device type, and the device channel to add the device.
Click “ Finish “.
Step 4. Move the mouse pointer over the ID number. Right click the mouse
and then select “Connect Videos”.
After several seconds, you can view the remote live streaming.
Access the Security System via a Web Browser
Step 1. Launch the IE browser. Enter
http://sight.annke.com and press the Enter
button.
Step 2. Enter the ID, username and password to get the live view.
| For more information, please visit:
---|---
Manufacturer: Shenzhen Kean Digital co.,Ltd.
Address: Room 1001, Rujun Building, No.105 Center Road,
Bantian Street, Longgang District, Shenzhen, China. 518000
Tech Support Email Address: support@annke.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>