ANNKE WPT400 4MP PTZ Outdoor Security Camera Instruction Manual
- June 14, 2024
- ANNKE
Table of Contents
ANNKE WPT400 4MP PTZ Outdoor Security Camera
Product Information
Specifications
- Applies to : DW81KD/DW61LD/DW41JD/S500/I81CK/I71BL/I71BK/I81CG
- Protocol : ONVIF
- Camera Resolution: Equal to or lower than the recording resolution of DVR
- Connection: Ethernet cable or Wi-Fi
Product Usage Instructions
Step 1: Register and Connect Camera to Myannke Account
- Power on the camera and place it close to the router.
- Run the Myannke App and click on the icon at the top-right corner.
- Choose “Smart Camera” and scan the QR Code on the camera.
Step 2: Enable ONVIF on Camera
- After connecting the camera to Myannke, click on the setting interface.
- Click on “ONVIF” to enable it.
- Set a password for the camera to enable ONVIF.
Step 3: Connect Camera to DVR via ONVIF
- Access the system menu of the DVR on the monitor.
- Go to “Camera” > “IP Camera” > “Custom Add” to find the IP camera.
- Select the camera and enter its password. Make sure the protocol is set to ONVIF.
- Click on “Add” after entering the correct password.
- When the status shows the successful connection icon, the camera is connected to the DVR.
- Go to “Live View” and double click on the name of the camera to see the IP camera.
FAQ (Frequently Asked Questions)
- Q: What are the necessary requirements for the IP camera?
- A: The IP camera should support ONVIF and be activated. Its resolution should be equal to or lower than the recording resolution of the DVR.
- Q: How should I connect the DVR and IP camera?
- A: Connect them to the same router or switch using an Ethernet cable. Alternatively, you can connect the camera to the same router via Wi-Fi.
- Q: Who should I contact for further assistance?
- A: For any other questions or technical support, please contact ANNKE at support@annke.com by email.
ANNKE VISION–How to Connect Myannke Camera to DVR via Onvif (S500)
- Applies to: DW81KD/DW61LD/DW41JD/S500/I81CK/I71BL/I71BK/I81CG
Introduction
When the user wants to connect the Myannke camera to ANNKE DVR, the camera needs to be connected to the ANNKE DVR by ONVIF protocol. You may refer to this article to find detailed instructions.
The necessary requirements for the IP camera.
- Make sure the camera supports ONVIF and has been activated.
- Camera’s resolution is equal to or lower than the recording resolution of DVR. For example, if the DVR can MAX support 5MP IP camera, but the IP camera`s resolution is 8MP. Then the IP camera cannot work with the DVR.
- Connect the DVR and the IP camera to the same router or switch by ethernet cable.(It also works if the camera is connected to the same router by WIFI)
Steps
- Register an account with Myannke and connect the camera to your account.
- Run the App, click the icon at the top-right corner.
- Choose the “Smart Camera”
- Please note to power on the camera and place the camera and phone close to the router!
- Please scan the QR Code on the camera.
- The picture below is to tell you how to find the QR code.
- After you connect the camera to Myannke, please click the setting interface and then click the icon to enter the “onvif” to enable the onvif.
- Please set a password of the camera to enable onvif.
- After you enable the onvif of the camera successdully, please access the system menu of DVR on the monitor and go to ‘Camera→IP Camera→Custom Add’ to find the IP camera.
- Choose the camera and then input the password of the camera.
- Please note the protocol should be ONVIF
- Click on Add after inputting the correct password.
- When the status shows the icon , the camera is connected to the DVR successfully.
- You can go to go to ‘Live View’ to double click the name of the camera to see the IP camera.
If you have any other questions, please contact ANNKE technical support at support@annke.com by email.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>