lxnav Can Remote Control Stick Instruction Manual
- June 6, 2024
- lxnav
Table of Contents
INSTALLATION MANUAL
LXNAV CAN Remote
Control stick
Version 1.11
Important Notices
The LXNAV CAN Remote is designed for VFR use only. All information is
presented for reference only. It is ultimately the pilot’s responsibility to
ensure the aircraft is being flown in accordance with the manufacturer’s
aircraft flight manual. The LXNAV CAN Remote must be installed in accordance
with applicable airworthiness standards according to the country of
registration of the aircraft.
Information in this document is subject to change without notice. LXNAV
reserves the right to change or improve its products and to make changes in
the content of this material without the obligation to notify any person or
organization of such changes or improvements.
A Yellow triangle is shown for parts of the manual that should be read
carefully and are important for operating the system.
Notes with a red triangle describe procedures that are critical and may result
in loss of data or any other critical situation.
A bulb icon is shown when a useful hint is provided to the reader.
Limited Warranty
This LXNAV CAN Remote product is warranted to be free from defects in
materials or workmanship for two years from the date of purchase. Within this
period, LXNAV will, at its sole option, repair or replace any components that
fail in normal use. Such repairs or replacements will be made at no charge to
the customer for parts and labor, the customer shall be responsible for any
transportation cost. This warranty does not cover failures due to abuse,
misuse, accident, or unauthorized alterations or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY
ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL LXNAV BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO
USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the
exclusion of incidental or consequential damages, so the above limitations may
not apply to you. LXNAV retains the exclusive right to repair or replace the
unit or software, or to offer a full refund of the purchase price, at its sole
discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH
OF WARRANTY.
To obtain warranty service, contact your local LXNAV dealer or contact LXNAV
directly.
Technical Data
- Power input 8-18V DC
- Consumption at 12 V: 60mA
- Weight 300g
Versions
Functionality
Standard version with custom configurable function button “Fn”| Schempp-Hirth version with red starter button for M gliders| EB28 version with trim switch
Diameter of command handles
Diameter | Gliders |
---|---|
19,3mm | DG, LAK, Schempp-Hirth |
20,3mm | LS, Stemme, Apis, EB29 |
24,0mm | Schleicher, Pipistrel Taurus, Alisport Silent, EB28 |
25,4mm | JS |
Shapes
Left-handed (optionally)| Symmetrical (optionally)| Right-handed (standard order)
Installation
LXNAV remote stick is connected to CAN bus through Remote-Can adapter.
Be careful, that connect the correct color wire to the pin, which is marked
with the same color.
PTT wires are connected to the radio, SC is connected to the Speed to fly
input of vario unit.
The remote stick will not operate until is registered on the device. The
remote stick can be registered under a setup-hardware-Remote stick.
Registration must be done on each unit (S80 and S80D)
The can bus is under power supply at all times, consequently, the remote stick
is also under power. After the flight, please disconnect batteries or switch
off the master, to prevent discharging batteries.
Remote with trim switch
Remote can be ordered with 3 position momentary switch for trimming purposes. Such remote has four additional wires with the label “IN: WHITE, OUT: RED” where two white wires should be wired to positive and negative potential in a glider, and the second pair of red wires go to the trim driver. Polarity is not important, if the trimmer has the wrong moving direction simply switch one pair of wires between them and the direction will be reversed.
Remote with starter button
This option is for gliders with electric starters on internal engines. Remote has a red momentary button for starting engines on the ground or in the air. The button is in a normally open configuration and makes contact when it is pressed. Coaxial cable is separated from other wires and labeled as “Starter” and should be wired to the engine control unit as stated in their manual.
Functions
Remote without SC cable
We have been working very hard to simplify the remote stick so that we can
have the same functionality but use fewer cables. The LXNAV new remote stick
comes without the standard SC cable but the functionality is still available.
With the new stick, there is no more need to solder these wires to the Vario
wiring loom. The SC function is programmable through S8/80/S10/S100.
To make the SC function work with the new stick, please check the SC setting
in the configuration/setup page. Go to Setup- >Hardware->Digital inputs
Please make sure that NONE of the input is set to “SC on/off switch” or “SC
toggle button”.
Dimensions
Normal insert
Slanted insert
Mounting screws (DIN 916/ISO 4029 M 3 x 6)
Revision history
Rev | Date | Comment |
---|---|---|
1 | Apr-18 | Added chapter 1, 3, 6 and 7 |
2 | May-20 | Added chapte7 |
3 | Jan-21 | Style update |
4 | Feb-21 | Updated chapter 7 |
5 | May-21 | Added chapters 4.1 and 4.2 |
Updated chapter 7
The pilot’s choice
LXNAV d.o.o.
Kidrioeva 24, SI-3000 Celje, Slovenia
T: +386 592 334 00 | F:+386 599 335 22 |
info@lxnay.com
www.lxnay.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>