PARKSIDE 16L Backpack Pressure Sprayer Instruction Manual

16 L BACKPACK PRESSURE SPRAYER
Assembly, operating and safety instructions
IAN 356373_2007

IMPORTANT SAFETY INSTRUCTIONS!
READ CAREFULLY BEFORE USING THE
PRODUCT AND KEEP FOR FUTURE REFERENCE!

Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. Familiarise yourself with the product before using it for the first time. In addition, please carefully refer to the operating instructions and the safety advice below. Only use the product as instructed and only for the indicated field of application. Keep these instructions in a safe place. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

Proper use

The product is used for spraying liquids in the garden and well ventilated greenhouses. The spraying of solvents or solvent-containing liquids or oil is a particular example of improper use of the product. This product is intended for private use only. The pressure spraying device is used only for spraying the following fluids in the garden or in well ventilated greenhouses.

• Water,
• The application of BVL-approved liquid pesticides (BVL: German Federal Office of Consumer Protection and Food Safety)

The sprayed agent may only be sprayed in the concentration specified by the manufacturer of the agent. If in doubt, consult the manufacturer of the agent. The pressure spraying device is designed for private use only.

Incorrect use includes, in particular, the spraying of the following:

• Solvents or liquids containing solvents
• Oil
• Easily flammable fluids
• Corrosive fluids such as acids or alkalis.

Description of parts and features (Fig. A)

and double conical nozzle  [25] )
20. Spray lance| 34. Seal washer sheet ø16 mm

Extra Spare Parts (included) (see fig. M)

8. Holder for lever handle
34. Seal washer sheet ø16 mm
35. Piston
36. O-ring ø15 mm
37. Collet
38. Aligning buckle
39. O-ring ø18.5 mm

Technical data

Max. permissible operating pressure
(including the entire nozzle [23],[24],[25] ,[26] ):| approx. 2–4 bar
Average flow rate of different nozzles at common working pressure of 3 bar:| 0.85 l / min (Conical nozzle [23] )
0.90 l / min (Fan nozzle [24] )
1.40 l / min (Double conical nozzle [25] )
1.20 l / min (Fourhole nozzle [26] )
Size of nozzles:|  ø 1.77 mm (Conical nozzle [23] )
1.4 x 0.7 mm (Fan nozzle [24] )
ø 1.77 mm (Double conical nozzle [25] )
ø 1 mm (Four-hole nozzle [26])
Size of filter inside spray tube handle [19] :| ø 0.7 mm
Size of filter screen [31] :| ø 1.1‒1.8 mm
Pressure-regulating value [22] :| 1.4 ± 0.2 bar (Open pressure)
1 ± 0.15 bar (Close pressure)
---|---
Operating temperature:
Carrying method:| 0–40 °C
At the operator‘s back, using the carrying belts [30]

Included items

• 1 Garden pressure sprayer
• 1 Spray tube
• 1 Pair of carrying belts
• 1 Hose
• 1 Assembly, operating and safety instructions

Spare parts:

• 1 Piston
• 4 Seal washer sheet ø 16mm
• 2 O-ring ø15 mm
• 2 O-ring ø18.5mm
• 2 Collets
• 1 Aligning buckle
• 1 Holder for lever handle

Safety advice

General safety advice

KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE!

• Children or persons who lack the knowledge or experience to use the device or whose physical, sensory or intellectual capacities are limited must never be allowed to use the device without supervision or instruction by a person responsible for their safety. Children must never be allowed to play with the device.

• Warehousing of pesticide. It shall be kept out of reach of children. Disposal of pesticide shall follow the safety instructions furnished its manufacturer

• Keep spraying requirement away from children and young persons under 16.

• Do not leave the device unattended while it is in operation. Use the device as intended!
  WARNING! Secure the device during transport to prevent the spray liquid escaping.
  WARNING! Examine the product before each use, ensure it is free of damages, congestions and all parts work as intended. Rubber parts such as the hoses or O-rings must not show any cracks or appear porous. Pay particular attention to the safety devices. Ensure all connections are fitted tightly. Examine the product before first use after winter.
  CAUTION: Do not use the product if any visible damage or loss of functionality.
  

• Always place the device on an even, flat surface.
  WARNING! During the sprayer is being filled, adjusted, used, transported, emptied, cleaned or maintained. Protect yourself with suitable personal protective equipment (PPE).

• Wear eye protection ( goggles or face shield )

• Wear respiratory protection and appropriate protective clothing

• Wear a water-proof glove and rubber boots

• Read the instruction handbook

• Keep bystanders away when spraying
  WARNING! Only use spare parts and accessories provided by the manufacturer (pls. follow the step of “Exchange of spare parts included“ described in the manual). All other repairs shall only be carried out by the manufacturer, its service agent or similarly qualified persons. Improper maintenance can lead to a hazardous situation.

• Wash your hands and face after each spraying session.

• In case of intoxication via skin contract, please rinse with water immediately and consult doctor advice.
  CAUTION! RISK OF EXPLOSION! Do not place the device (empty or full) in direct sunlight and frost.

• Always read and observe the information provided by the chemical manufacturer when working with or mixing spray solutions.

• Only mixing and filling the sprayer outdoors or in well-ventiled greenhouse.

• All the applicant and liquid for the device shall not over 40°C and refer to the information provided by chemical manufacturer.

• Never mix more spray solution/pesticide then is required.
  WARNING! Do not dispose of residues in the drains. Disposal shall follow the safety introduction according to chemical manufacturer. Do not exceed the nominal volume! Ensure the liquid to be sprayed is compatible with the product. Ensure that the use of the pesticide, liquid fertiliser or cleaning agent is permitted in your country. WARNING! Do not store the device in livestock buildings due to the ammonia vapours (danger of brass cracking), do not fill with solutions containing nitrogen or phosphates.

• Do not store spraying pesticides in the device.

• Never spray into wind, water, or drinking water source. Never spray at human or animals.
  WARNING! Take into account of wind, rain and other climate and environmental conditions to avoid hazard of uncontrolled or unintended liquid distribution. Avoiding drift during spraying operation.

• Do not use device when any leakages, uneven spray jet.

• Release the residual pressure after each use.

• Before each use, pls. ensure the device is in good condition. Pay attention to the tightness of the screw connection and appearance of the device. If damage is suspected and leakage found, take out of the operation immediately.

• Do not blow out blocked nozzles using the mouth.

• The sprayer may not be used if the operator is tired, ill or under influence of alcohol, drugs or medication.

• Procedure after accidents: If you contact with the spray solution or the blockage of spraying occurs after pressurized, release the pressure sprayer immediately by unlocking the belt hook [27] and sliding the pressure sprayer down the floor. Danger to health due to contact with the plant protection products! Plant protection products may cause damage to health by inhalation, ingestion or absorption through the skin. If symptoms occur or in case of doubt, seek medical advice. Therefore, observe the following safety instructions:
  – Observe the safety instructions on the labels of the plant protection products. Observe the specified max. concentration. Certain liquids require protective goggles, gloves or other protective measures.
  – Always request a safety data sheet from the spray manufacturer. – Always empty the residue pressure and spray solution according to “Emptying the pressure sprayer and disposal of spray solution” when you are safe. You shall also clean the filter on spray tube handle [19] to avoid any blockage.

• Only trained, healthy and rested operators may work with the product.

• Ensure inexperienced users receive a proper training before use.

Explanation of the symbols used:

| 16- l pressure sprayer| | Keep away from naked flames and heat sources. Seal containers securely. Store in a fireproof way! Do not use easily flammable fluids!
---|---|---|---
| Permissible operating pressure: Max. approx. 2‒4 bar| | Protect from frost and store away from frost.
| Not for use with corrosive substances!| | Store at 0 °C–40 °C in a dry, dustfree location.
| Do not spray on electrical devices, electrical cables or wires.| | Wear eye protection
| Do not spray on people!| | Wear respiratory protection
| Do not spray on animals!| | Wear appropriate protective clothing
| Spray on plants only!| | Wear water-proof rubber boots
| Do not use the product for drinks!| | Wear water-proof glove
| Do not leave the pressurized spraying device standing in the sun. There is a risk of explosion!| | Before using for the first time, pls read the instruction carefully.

About the pressure regulating valve

The Pressure Regulating Valve [22] is an important device to reduce spraying pulse, maintain the constant pressure, ensure even spraying, minimize environmental pollution and enhance the pest control performance.

The Pressure Regulating Valve [22] is normally opened at pressure of 1.4± 0.2 bar, and normally closed at pressure of 1± 0.15 bar. When the pressure inside the tank [3] increases above open pressure, the sprayer can start spraying by compressing its spray trigger [17]. When the pressure is lower than the close pressure, the regulating valve [22] will shut off automatically and stop spraying. You shall pressurize the pump [10] if you desire to proceed spraying.

Note: Residual pressure still exists in the tank [3] due to the regulating valve [22], even though spraying was finished. Loosen the union nut [16] and remove the spray tube [20]. Open the lid of container [1], move the spray tube toward into the opening of tank [3], press the spray trigger [17] to release the residual pressure above the opening of tank [3].

Exchange of Nozzles

WARNING! Protect yourself from hazardous substances during exchanging the nozzles by wearing suitable personal protective equipment (PPE) (eye protection, respiratory protection, protective clothing, waterproof gloves and boots).
CAUTION! Check safe function!

• Lossen the nozzle [23], [24], [25] or [26] from the pressure regulating valve [22].
• Replace and fasten the nozzle [23], [24], [25] or [26] to the pressure regulating valve [22].

Before use

WARNING! Protect yourself with suitable personal protective equipment (PPE) of wearing eye protection, respiratory protection, appropriate protective clothing, water-proof gloves and boots from hazardous substances.
CAUTION! Check that the device is functioning properly! Check the pressure sprayer be- fore each use to ensure that it is free of visible damage and is functioning safely. To do this, carry out the following tests and inspections:

• The hose [13] or O-rings [36], [39] must not show any cracks or appear porous.
• Check the container [3], the hose [13] and the carry belts [30] for visible damage.
• Check that the hose connections [12] and [14], pipe connection [16] and [21], pressure regulating valve [22] and nozzles [23] [24] [25] or [26] are fitted tightly.
• Check that the lid of container [1] and lid of air chamber [11] are closed tightly.
• Trial spraying with clean water and a check of tank, hose, shut-off and nozzle for possible leakage are required prior to operation.
• Check that the filter screen [31] and filter on spray tube handle [19] are not blocked. Filter screen [31] and filter on spray tube handle [19] are for filtering the solid substance.”

Bringing into use

WARNING! Protect yourself with suitable personal protective equipment (PPE) of wearing eye protection, respiratory protection, appro priate protective clothing, water-proof gloves and boots from hazardous substances. Only mixing and filling outdoors or in well-ventilated greenhouse.

Attaching the spray tube (Fig. B–E)

• Attach the conical nozzle [23], fan nozzle [24], double conical nozzle [25] or four-hole nozzle [26] to pressure control valve [22]. Fasten the nozzle in a clockwise direction.
• Attached the pressure regulating value [22] to the union nut [21] on spray tube [20]. Tighten the union nut [21] .
• Insert the spray tube 20 into the spray tube handle [15], then tighten with the union nut [16] .
• Connect the hose 13 to the spray tube handle [15], tighten the union nut [14].
• Tighten the union nut [12] in a clockwise direction.
• Fasten the lid of air chamber [11] as far as it goes.
• Attach the belt hook [27] to belt hook holder [5].
• Adjust the length of belts [30] with the belt buckles [29] and move the belt pads [28] for suitable carrying position.
  Note: adjust in the same way before wearing to give even load.
  Note: The device must worn as close to the body as possible and parallel to the spine.

Filling the pressure sprayer tank (Fig. F)

WARNING! Only mixing and filling outdoors or in well-ventiled greenhouse.

• Check the volume application rate when filling the liquid into the sprayer.
  Note: Before using the product, check to see that it is in good condition and free of defects.

• Click the spray tube [20] on the spray tube holder [9] (s. fig. I).

• Unscrew the lid of container [1] in an anti-clockwise direction and open.

• Now fill the tank with prepared mixture through the filter screen [31] carefully. Filter screen [31] is for filtering the solid substance.
  Note: Fill the tank with only the amount of liquid that you actually need for that particular spraying session (not more than 16 l).

• Note safety instructions on the labels of the spraying pesticides used. Pay attention to the stated max. concentrated.

• Always request a safety data sheet from the spraying agent manufacturer.

• Place the lid of container [1] back onto the container [3] and fasten in a clockwise direction clockwise as far as it will go.

Changing of chemicals

• Pls. follow the step of “Emptying the pressure sprayer and disposal of spray solution” described in the manual
• Pls. follow the step of “Cleaning and care” described in the manual .
• Check the product according to the “Before use” described in manual.
• Pls. follow the step of “Filling the pressure sprayer tank” described in manual.

Building up the operating pressure (Fig. G)

• General the pressure through the pump [10] by moving lever handle [6] on levers [7] up and down until the pressure sprayer has been pumped up to a pressure not exceeding the maximum permissible operating pressure of 4 bar.
• When carrying the tank [3] with spraying process, can generate the pressure by moving the levels handle [6] on levers [7] up and down with left hand if the pressure in the tank [3] becomes low.

Spraying

• Carry the pressure sprayer over your shoulder by the carrying belts [30].
  Note: Ensure that the pressure sprayer is always kept upright. Only when held in this orientation will the sprayer work properly.

• Hold the spray tube handle [15] firmly by the hand and direct the spray nozzle [23] , [24] , [25] or [26] e.g. at a plant.

• Press the trigger [17] to start the spraying process.
  Note (Fig. H): For continues spraying, move the spray lock [18] backward. To release continues spray, move the spray lock [18] toward.

• Release the trigger [17] to stop the spraying process.
  Note: When the pressure in the container [3] is no longer sufficient to spray, pump the container [3] to increase the pressure again up to but not exceeding the maximum permissible operating pressure of 4 bar (see “Building up the operating pressure”).

• Clip the spray tube [20] on spray tube holder [9] during work interruptions and breaks.
  Note (Fig. I): The nozzle [23], [24], [25], [26] always on the top position when the spray tube [20] is clipped onto the spray tube holder [9] .

• After spraying, loosen the union nut 16 and remove the spray tube [20]. Open the lid of container [1], move the spray tube handle [15] toward into the opening of tank [3], press the spray trigger [17] to release the residual pressure above the opening of tank [3]. For the residue spray solution, pls. follow the step of “Emptying the pressure sprayer and Disposal of spray solution” described in the manual.

Emptying the pressure sprayer and disposal of spray solution

WARNING! Always release residual pressure before transport and cleaning. Protect yourself with suitable personal protective equipment (PPE) from hazardous substances. Take precautions to avoid environmental contamination from hazardous substances.

• Loosen the union nut [16] and remove the spray tube [20].
• Open the lid of container [1], move the spray tube handle [15] toward into the opening of tank [3],
• Press the spray trigger [17] to release the residual pressure above the opening of tank [3].
• Remove any leftover spray product from the tank and the pipes and store it in a suitable container.
• Do not dispose of residues down the drain. Dispose shall follow the safety introduction according to the chemical manufacturer.
  WARNING! Always keep the product away from other people during emptying and disposal.

Transport of the pressure sprayer

WARNING! Protect yourself with suitable personal protective equipment (PPE) of wear- ing eye protection, respiratory protection, appro priate protective clothing, water-proof gloves and boots from hazardous substances. Only mixing and filling outdoors or in well entitled greenhouse.
WARNING! Make sure to release pressure & empty the container [3] before transportation.

• Secure the product against falling, overturn, vibration, extremely high or low temperatures, direct sunlight and impacts during transportation to avoid damages.

• Tighten the sprayer with lid and all the union nuts during transport to prevent loss of fuel, damage or injury.

• Always kick the spray tube [20] onto the spray tube holder [9] (s. fig. I) for transport or storage.
  Note: Make sure that the pressure sprayer is always in an upright position.

• Transport after use, clean the device and dry. Follow the step of “Cleaning and are” described in manual. Kick the spray tube [20] onto the spray tube holder [9] (s. fig. I). Carry with the container handle [2].

Cleaning and care

WARNING! During cleaning, always protect yourself with wearing suitable personal protective equipment (PPE) of wearing eye protection, respiratory protection, appropriate protective clothing, water-proof gloves and boots from hazardous substances.
Note: Even after spraying has ended, there is still residual pressure in the container [3] due to the pressure regulating valve [22]. To release it, first loosen the pipe connection [16] and re- move the spray tube [20]. Open the cover of the container [1] and point the spray tube handle 15 at the opening of the container [3] . Press the spray trigger [17] to release the residual pressure over the opening of the container [3] .

• If the nozzle seems to be blocked, do not try to blow it free with your mouth.
  Note: Clean the pressure sprayer after each use! Empty the bottle after each use.

Clean the pressure sprayer

• The pressure sprayer shall be washed in an allowed site.
• Loosen the spray nozzle [23], [24] , [25] ,[ 26] from [22] pressure regulating valve and clean under running water.
• Loosen the nozzle cap [23a] , [24a] , [25a] , [26a] , clean under running water together with the inner parts of spraying sheet [23b] , [24b] , [25b] , split sheet [33] , seal washer sheet [34] .
• If the spray nozzle [23] , [24] , [25] , [26] is clogged, clean it by pushing a needle through it.
• Flush through the pressure sprayer, pressure regulating valve [22] , pipes and tubes with water.
• Remove the spray handle 15 from pressure sprayer and disassemble. Clean under running water together with the filter [19] and O-ring ø18.5mm [39] . Pls. use brush for clean the filter [19] (Fig J).
• Take out the filter screen 31 under running water with brush.
• The surface and inner part should be cleaned with high pressure injection water till drainage become clean (Fig. K). After clean, always kick the spray tube [20] onto the spray tube holder [9] (s. fig. I) for transport or storage.
• After operation and cleaning of product, al-ways change clothes and wash those exposed part of body such as hands and face. In case of toxic pesticide and germicide, a shower after operation is required to ensure safety.

Store the pressure sprayer

WARNING! Always release any residual pressure still present in the container [3] after use by following the step of “Emptying the pressure sprayer and disposal of spray solution“and“ Cleaning and care”.

• Thoroughly clean the device and allow it to dry before you put it away for the winter. This will avoid frost damage.

• Clip the spray tube [20] on spray tube holder [9] (s. fig. I).

• Store the pressure sprayer in a dry, dustfree place.
  WARNING! Do not store the device in livestock buildings due to the ammonia vapours (danger of brass cracking), do not fill with solutions containing nitrogen or phosphates.

• Check the product regularly each year after winter by using of clean water.

• Check product before each use. Check the product after each use.

Troubleshooting

If the measures listed below are not successful, contact the manufacturer.

• = Fault
• = Potential causes
• = Remedies

No pressure is established in the tank.

• The lid of container [1] is not firmly fastened into place.
• Fasten the lid of container [1] firmly into place.
• Fasten the union nut [12] , [14] , [16] and [21] firmly into place.
• The piston [35] may have been damaged
• Replace the piston [35] according to “ Replace included spare parts “ described in manual.
• Split pin [32] fetch way
• Re-tight the split pin [32] on the product properly.

Spray nozzle does not spray.

• No pressure present.
• Generate pressure through the pump [10] by moving the lever handle [6] .
• The spray nozzle is blocked.
• Stop use, unpressured, take care about pesticide to person and environment. Clean the spray nozzle [23] , [24] , [25] , [26] (Pls follow the step of “Cleaning and care“ section described in the manual).
• No spray in the tank.
• Fill with spray.
• Filter [19] is blocked.
• Clean the filter with brush (please refer to the “Cleaning and care” section).
• The seal-ring loose or is damaged.
• Re-tighten up or replace.

Rock Lever is too heavy to operate.

• Levers [7] is too tight.
• Check and adjust the levers [7] .
• Pump charmer [10] insufficiently lubricated.
• Apply lubricant.
• Nozzle [23] , [24] , [25] , [26] or filter [19] is blocked.
• Stop use, unpressured, take care about pesticide to person and environment. Clean with brush (please refer to the “Cleaning and care” section).
• Pump is block.
• Check the position of lever 7 and split pin [32] . Pls. contact its service agent or similarly qualified persons. Failure to do so may result in hazard.

Exchange of spare parts included

WARNING! Protect yourself with suitable personal protective equipment (PPE) of wearing eye protection, respiratory protection, appro priate protective clothing, water-proof gloves and boots from hazardous substances.
WARNING! Only use spare parts and ac- cessories provided by the manufacturer. All other repairs shall only be carried out by the manufacturer, its service agent or similarly qualified persons. Hazards can arise due to improper maintenance (Fig. M).
WARNING! After any replacement, pls. put all parts back together and check the product before use.

If found damaged with following part no.| Replace with the spare parts included in the package
---|---
Lever handle [8]| Remove the damaged holder for lever handle [8]  from the holder [9 ] and replace.
O-ring ø15 mm [36]| Loosen the nozzel cap [23]a, [24a]  or [25a], remove the damaged seal washer sheet ø16 mm [34]  and replace.
O-ring ø15 mm [36]| Loosen the union nut 16 from spray tube handle [15]  or the union nut [21] from the pressure regulating value [22], remove the damaged O-ring ø15 mm [36]  and replace.
Collet [37]| Loosen the union nut [16] from spray tube handle [15]  or the union nut [21] from the pressure regulating value [22], remove the damaged collet [37]  and replace.
Aligning buckle [38]| Remove the aligning buckle 38  from the levers [7]  on the bottom of sprayer and replace.
Pison [35]  (Fig. L)| Remove the split pin [32], disassemble the spray tube holder [9] and lever [7]  from prump [10 ]. Take out the pump [10]  with pump case[ 10a]. Hold the lid of air chamber [11] and remove the pump case [10a]. Remove the piston [35]  underneath the pump [10]  and replace. After replacement, pls. put all parts back together.
O-ring ø18.5mm [39]| Disassemble the spray handle [15] , Take out the damaged O-ring ø18.5mm [39]  and replace (Fig. J).

Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase.

Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. This warranty becomes void if the product has been damaged, or used or maintained improperly. The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions: Please have the till receipt and the item number (e.g. IAN 123456_7890) available as proof of purchase. You will find the item number on the rating plate, an engraving on the front page of the instructions for use (bottom left), or as a sticker on the rear or bottom of the product. If functional or other defects occur, please contact the service department listed either by telephone or by e-mail. You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

Service

Service Great Britain
Tel.: 08000569216
E-Mail: owim@lidl.co.uk

EC DECLARATION OF CONFORMITY

IAN: 356373_2007
Product identification: “PARKSIDE” 16L Backpack Pressure 
Model Number:  Sprayer FIG06876
The object of the declaration described above is in conformity with the relevant Community harmonisation legislation:
Directive 2006/42/EC
2009/127/EC amending Directive 2006/42/EC
References to the relevant harmonised standards used or references to the specifications in relation to which conformity is declared:
N° / Parts
Directive 2006/42/EC
EN ISO 19932-1:2013
EN ISO 19932-2:2013
Name and address of the manufacturer: OWIM GmbH & Co. KG Stiftsbergstrage 1 D-74167 Neckarsulm Germany
This declaration of conformity is issued under the sole responsibility of the manufacturer.
The original declaration of conformity![PARKSIDE 16L Backpack Pressure Sprayer

• sig](https://manuals.plus/wp-content/uploads/2022/03/PARKSIDE-16L-Backpack- Pressure-Sprayer-sig-550x130.jpg)

OWIM GmbH & Co. KG
Stiftsbergstraße 1
74167 Neckarsulm
GERMANY
Model-No.: HG06876
Version: 11 / 2020
Last Information Update
03 / 2021 · Ident.-No.: HG06876032021-4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>