spigen GTS12W OneTap SmartLock Noiseless Wireless Car Charger User Manual
- June 5, 2024
- Spigen
Table of Contents
GTS12W OneTap SmartLock Noiseless Wireless Car Charger
**User Manual
**
GTS12W OneTap SmartLock Noiseless Wireless Car Charger
Spigen OneTap SmartLock
Noiseless Wireless Car Charger for Galaxy Z Fold (Vent Clip)
User Manual
GTS12W
Product Contents
- Car Mount
- Locking Bolt
- Vent Clip
Installation Guide
-
Remove Locking Bolt
-
Vent Clip Assembly
-
Install
-
Charging
The US and Canada Customers Only
Distributed by Spigen, Inc. in Irvine, CA 92618, USA
Manufacturer: Spigen Korea Co., Ltd.
3MN085530
Caution
- Vent Clip can only be installed on air event blades less than 4.5mm (0.18in) thick.
- When installing Vent Clip, only 7.5mm (0.3in) apart from the vehicle vent blade can be installed.
Note
- B Class Equipment (Equipment for home use)
- This product is mainly for home use with radio wave acceptability registration; therefore, it can be used in all areas.
Specifications
Model | GTS12W |
---|---|
Input | DC 5.0V 3.0A, 9.0V 2.0A, 12.0V 1.5A |
Output | 5.0W, 7.5W, 10.0W, 15.0W |
Dimensions | 154.50 x 73.61 x 127.27mm / 6.08 x 2.90 x 5.01in |
Weight | 180.20g / 6.35oz |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
The following importer is the responsible party (for FCC matters only).
Spigen Inc. 9975 Toledo Way #100, Irvine, CA 92618
USA E-mail: spigen.support@spigen.com
IC Statement
This digital apparatus complies with CAN ICES-003(B)/NMB-003(B) This device complies with Industry Canada license ICES-003. Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
CAN RSS-216 / CNR-216
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with a minimum distance 20cm between the
radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>