elk Home 89697-6 28 Inch Wide 6 Light Chandelier Installation Guide

: June 16, 2024
: elk HOME

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk Home 89697-6 28 Inch Wide 6 Light Chandelier Installation Guide

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING: This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

Carefully pull house wires down out of junction box so house wires are easily accessed to connect fixture wires.
If screw collar loop (W) is already attached to mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threaded pipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor. From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E). Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
Place mounting bracket (A) up against junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box.
Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.
Carefully push fixture wires from top of fixture body (O) up through bottom of center stem (M). Pull fixture wires taut. Screw center stem (M) onto top of fixture body (O).
Push fixture wires up through threaded pipe (S). Pull fixture wires taut. Thread bottom of threaded pipe (S) onto top of center stem (M).
Hold on arm (L) so threaded stud on end is at the top. Arm should curve inward toward the center stem (M). Insert bottom of arm into hole in ball on fixture body (O). Repeat this step for remaining arms (L).
Pass fixture wires up through hole in bottom of cup (K). Slip hole in bottom of cup (K) over top of threaded pipe. Fit threaded studs on top of arms (L) into small holes along cup (K).
From inside cup (K), slip one washer (P) onto each threaded stud. Screw one threaded ball (R) onto each threaded stud. Tighten threaded balls (R) to secure cup (K) to arms (L).
Pass fixture wires through hole in center of cap (T). Pass hole in cap (T) over end of threaded pipe protruding from cup (K).
Push fixture wires up through bottom of loop (X). Pull fixture wires taut. Screw bottom of loop (X) onto top of threaded pipe (S). Tighten loop (X) to secure cap (T) in place. DO NOT over tighten.
Connect one locking link (G) to loop (X).
Determine desired hanging height of fixture.
Cut chain (H) to length to achieve desired height.
Slip chain link at end of chain (H) onto locking link (G) on loop.
Weave fixture wires through chain links, skipping every other chain link.
Slip threaded ring (F) down over end of chain (H).
Position canopy (D) so outside of canopy is pointing down towards fixture. Slip hole in canopy (D) over end of chain (H).
Strip 3/4″ of insulation from ends of fixture wires.
Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar G loop (W).
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Remove second locking link (G) from last link on chain (H) and screw collar loop (W).
Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.
Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (W).
Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.