LDSystems IMA RK Rack and Under Table Mount Kit For IMA 30 and IMA 60 User Manual

June 6, 2024
LDSystems

LDSystems logo m1

USER´S MANUAL

LDSystems IMA RK

IMA RK

RACK- AND UNDER TABLE MOUNT KIT FOR IMA 30 / IMA 60
LDIMARK

YOU`VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience as a manufacturer of high-quality audio products. Please read this User`s Manual carefully, so that you can begin making optimum use of your LD Systems product quickly.
You can find more information about LD-SYSTEMS at our Internet site WWW. LD-SYSTEMS.COM

SAFETY INFORMATION
  1. Please read these instructions carefully.
  2. Keep all information and instructions in a safe place.
  3. Follow the instructions.
  4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
  5. Use the equipment only in the intended manner and for the intended purpose.
  6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.
  7. During installation, observe the applicable safety regulations for your country.
  8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
  9. Never place sources of ignition, e.g., burning candles, on the equipment.
  10. Ventilation slits must not be blocked.
  11. Keep a minimum distance of 20 cm around and above the device.
  12. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment – in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases. Avoid direct sunlight!
  13. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.
  14. Make certain that objects cannot fall into the device.
  15. Use this equipment only with the accessories recommended and intended by the manufacturer.
  16. Do not open or modify this equipment.
  17. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
  18. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.
  19. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in another way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.
  20. Clean the equipment using a dry cloth.
  21. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.
  22. Plastic bags must be kept out of reach of children.
  23. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
INTRODUCTION

The seven-piece IMA RK rack- and under table mount kit allows you to install the mixing amplifiers of the IMA series into a 19-inch rack, under a shelf, a table or under a counter.

The following configurations are possible:

  • One IMA device in a 19-inch rack (2 RU)
  • One IMA device under a table, a shelf, or under a counter
  • Two IMA devices together in a 19-inch rack (2 RU)

The set includes one long rack mount bracket, two short rack / shelf mount brackets, two small plates for the back, two big plates for the bottom side, four M4 flat-headed screws for the rack mount brackets and eight M3 countersunk screws for the bottom plates.

FEATURES
  • Rack and under table mount kit for IMA series mixing amplifiers
  • For mounting one single unit or two units together
  • One IMA device in a 19-inch rack (2 RU)
  • One IMA device under a table, a shelf, or under a counter
  • Two IMA devices together in a 19-inch rack (2 RU)
  • Seven-piece installation set including screws

RACK MOUNTING (rack mounting kit LDIMARK optionally available)

The optionally available rack mounting kit LDIMARK includes rack-mount brackets and connectors for installing a single IMA 30 installation mixing amplifier, as well as for adjacently installing two amplifiers in a 19″ rack. The set includes: 2x rack-mount brackets with short sides A , 1x rack- mount bracket with long sides B , 2x small plates for the back C , 2x rectangular plates for the bottom D , 4x M4 flat-headed screws for the rack-mount brackets, 8x M3 countersunk screws for plate D.

LDSystems IMA RK - RACK MOUNTING 1

Installing a single amplifier requires a rack-mount bracket with short sides A and the rack-mount bracket with long sides B. Screw the bracket with the short sides to the left or right side of the amplifier and the bracket with the long side on to the opposite side. Use the included M4 flat-headed screws for this.

LDSystems IMA RK - RACK MOUNTING 2

To install two amplifiers alongside each other in a 19″ rack, you will need the two small plates to join for connecting the amplifiers on the back C , the two rectangular plates to join the amplifiers on the bottom D and the two rack-mount brackets with short sides A. Loosen the screws on the back at the corresponding positions and use them to screw on the plates C. Screw the connectors D , as illustrated below, on to the corresponding positions on the amplifiers with the included M3 countersunk screws. Use the M4 flat-headed screws to screw the rack-mount brackets with the short sides A on to the sides of the devices.

LDSystems IMA RK - RACK MOUNTING 3

LDSystems IMA RK - RACK MOUNTING 4

LDSystems IMA RK - RACK MOUNTING 5

UNDER-TABLE MOUNTING (rack-mount bracket included in optionally available rack mounting kit LDIMARK).

For under-table mounting, there are two M4 screw holes located on the upper edge of both sides of the housing. Use the included M4 flat-headed screws to tightly screw the two rack-mount brackets A with short sides to each side of the housing as illustrated. The amplifier can now be attached in a suitable position below a desktop.

LDSystems IMA RK - UNDER-TABLE MOUNTING

TECHNICAL DATA
Item number LDIMARK
Product type Accesories for Mixing amplifiers
Material Steel
Finish Painted black
Material thickness 1,5mm-2mm

Included accessories:
Included accessories:| 0,43 Kg per part
1x long rack mount bracket| 0,11 Kg per part
2x short rack mount brackets| 0,015 Kg per part
2x rectangular plates for the bottom| 0,003 Kg per part
2x small plates for the back| Black
Color| 0,58 Kg

MANUFACTURER´S DECLARATIONS

MANUFACTURER`S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_ LD_SYSTEMS.pdf To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach / Email: Info@adamhall.com / +49 (0)6081 / 9419-0.

CORRECT DISPOSAL OF THIS PRODUCT
(valid in the European Union and other European countries with a differentiated waste collection system)
This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste for disposal.

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation

CE COMPLIANCE
Adam Hall GmbH states that this product meets the following guidelines (where applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at www.adamhall.com.
Furthermore, you may also direct your enquiry to info@adamhall.com.

EU DECLARATION OF CONFORMITY
Hereby, Adam Hall GmbH declares that this radio equipment type is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.adamhall.com/compliance/

LDSystems logo m1

LD-SYSTEMS.COM

Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com

      REV: 01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals