muse MT-106 BT Turntable Stereo System User Manual

: June 3, 2024
: muse

Table of Contents

muse MT-106 BT Turntable Stereo System
TURNTABLE STEREO SYSTEM
SPECIFICATIONS
- GENERAL
- MORE INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

muse MT-106 BT Turntable Stereo System

muse-MT-106-BT-Turntable-Stereo-System-product-image

Read the instructions carefully before operating the unit.

TURNTABLE STEREO SYSTEM

LOCATION AND DESCRIPTION CONTROLS

Lift lever
AUTO STOP (ON/OFF) switch
Tone arm rest
Speed selector (33/45/78)
PITCH knob (to adjust the speed of pal
Tom arm
MODE button (to select BLUETOOT PHONO, AUX IN, USB mode)
Mode indicator
POWER ON/OFF and volume cont (MIN/MAX)
Phones jac
Cartridge with stylus
Spindle
45 RPM adaptor
USB port
BACK button
REC / : RECORD/ PLAY/ PAUSE button
SPLIT/ : Segmented record/ next button
External device output jack
AUX IN jack
DC IN 5V JACK

POWER SUPPLY

using the AC adaptor

AC adaptor:
Input 100-240V 50/60Hz, 0.4A
Output 5V 2000mA muse-MT-106-BT-Turntable-Stereo-
System-02

The supplied AC adaptor is suitable for use on AC main supplies of 100-240V AC and should only be connected to a mains supply within these parameters.

Caution:

The included AC adapter is exclusively intended to be used with this device.
Turn off the power before unplugging the AC adapter to avoid damaging the device.
In case of unused for long periods, unplug the AC adapter from the outlet.
Place the unit near the outlet and make sure it is easily accessible. If a malfunction occurs, immediately disconnect the unit from the wall outlet.
The adapter enables you to unplug the unit. It must be easily accessible during use.
To completely turn off power, unplug the adapter from the wall outlet.
Never use a damaged power adapter. Place the power cord safely and so that you do not pinch or crush it. If the cable is damaged, contact a repair service.

TURN ON/ OFF THE UNIT

To turn the unit on, rotate the POWER ON/OFF switch clockwise until a “click” is heard and set the volume (MIN/MAX) to a lower level.
When you have finished the unit, rotate the POWER ON/OFF switch counter-clockwise until a “click” is heard to turn off the unit.

LISTEN TO THE PHONO

When the unit is on, rotate the MODE button to select the phono mode, function indicator light becomes red.
Place a record on the turntable platter and select the desired speed (33/45/78) according to the record.
NOTE: If you are playing 45RPM singles, place the 45 RPM adapter on the center spindle.
Set the AUTO STOP ON/OFF switch to ON or OFF position.
- If the AUTO STOP ON/OFF Switch is turned ON, the record will stop automatically when playback ends. If Auto Stop switch is turned OFF, record will NOT stop automatically when playback ends.
- AUTO STOP function applies to most 33RPM vinyl records. However, even if the AUTO STOP function is ON, it may happen that some vinyl records ,e.g. 45RPM, will stop before playback comes to the end OR will not stop automatically when playback comes to the end. If the vinyl record stops before playback comes to the end, set the AUTO STOP switch to “OFF” position. Then playback will continue, but it will not stop automatically.
Remove the stylus cover from the stylus and released the Tone arm rest.
Push up the lift lever to raise the tone arm and gently move the tone arm to the desired position onto the record; Push down the lift lever, the tone arm slowly onto the record to start playing the record.
(When you pull down the lift lever, do not pull it beyond the position of tone arm rest.)
Rotate the PITCH knob to adjust the speed of platter.
Adjust the volume control (MIN/MAX) to your desired level.
Raise the tone arm and place it back in the rest and then turn off the power to prevent the turntable from spinning.

IMPORTANT: Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm Clamp could result in damage to the Tone Arm or Stylus.

USING THE AUX IN MODE

Connect your auxiliary source (e. g. mp3 player) to the AUX IN jack (3.5mm) on back of unit. (cable not included).
When the unit is on, rotate the MODE button to select AUX IN mode, indicator becomes blue and red. Normally use your external audio appliance, the sound automatically goes through the speakers of your device.
Adjust the volume (MIN/MAX) to the desired level.
Disconnect the external appliance from the auxiliary input to stop playback

LISTEN TO THE DEVICE USB

Connect a USB device containing MP3 files or MP3 player to the USB port.
When the unit is on, rotate the MODE button to select the USB mode, indicator becomes red flashing. The USB start to playback automatically. Press to pause, the indicator keep remain red without flashing.
Adjust the volume (MIN/MAX) to the desired level.
Press to skip forward to the next track or repeatedly to several tracks. Press return to the beginning of the track, or press repeatedly to skip backwards several tracks. Press and hold or to search quickly within a track.
Press to pause the USB playback

Removing the USB device
Please be sure to stop playback and turn the unit OFF before removing the USB device to avoid damage the USB and system

Note:

There are many USB devices in the market. We cannot guarantee to support all different models. Please try another USB device if yours is not supported.
The unit might not support all the multimedia files stored in USB because it includes some special playback procedure which might not be compatible with the procedure of this unit.

BLUETOOTH FUNCTION
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners

Pairing a Bluetooth Device

When the unit is ON, rotate the MODE button to select Bluetooth mode. Indicator becomes blue flashing.
On the Bluetooth device, enable Bluetooth and select “MUSE MT-106BT” from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a passcode, use “0000”. Some
Bluetooth devices will ask you to accept the connection. If the units are paired properly, you will hear an indication sound.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, press and hold the button to disconnect the device, and then follow the steps above to make a new connection.

On some devices such as computers, once paired you must select the unit from the
Bluetooth menu and choose “Use as Audio Device (stereo)” or similar.
Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the MT-106 BT’s speakers.
Press the button to pause playback. Press again to resume playback.
Select desired track with / .
Adjust the volume (MIN/MAX) to the desired level. You can also adjust the volume on the device to which you are paire

RECORDING FROM PHONO, AUX IN TO USB.

Connect the USB device to the USB port (Make sure the USB device have enough space to save the encoding).
Select one of your favorite mode (PHONO or AUX IN) and start your mode playback.
Press REC button till the indicator becomes blue and red flashing alternately to start the recording.
Press the REC button until the indicator becomes blue and red without flashing to stop the recording.
To listen the recording, rotate the MODE button to select the USB mode, indicator becomes red flashing, press / to find your track and listen your recording

SPLIT FUNCTION
Press SPLIT button when recording, the current record will be cut off and automatically stored in a file. Press SPLIT button again will generate another file.

NOTE: Press the button to stop the recording

USING HEADPHONES / EARPHONES
Maximum output voltage ≤ 150Mv

HEADPHONE VOLUME WARNING
Connect earphones with the volume set low and increase it if required. Prolonged listening through some earphones at high volume settings can result in hearing damage. When headphones/earphones are connected, no sound will be emitted from the unit’s speaker.

Caution: Avoid listening to sound at levels which may be harmful to your ears.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

USING THE RCA LINE OUT JACK
Connect one end of audio cable (cable not included) to the LINE OUT jack on the unit AUXILIAR and other end of cable connect to the RCA IN jack or AUX IN jack of your other audio drive equipment.

Turn on your audio drive equipment.
Select one of your favorite mode (BLUETOOTH, PHONO, AUX IN, USB) and start your mode playback.

HOW TO REPLACE THE TURNTABLE STYLUS (NEEDLE)

Removing the Stylus(needle) from the Cartridge

Raise the Tone Arm.
To remove the old stylus needle, Place a screwdriver at the tip of the stylus and push downward as shown in direction “A”.
Remove the stylus by pulling the stylus forward and pushing downward.

Installing the Stylus

Hold the tip of the stylus and insert the stylus by pressing as shown in direction “B”.
Push the stylus upward as in direction “C” until the stylus locks into the tip position.

TIPS FOR BETTER TURNTABLE PERFORMANCE

When opening or closing the turntable cover, handle it gently, gripping it either at the centre or at each side.
Do not touch the needle tip with your fingers; avoid bumping the needle against the turntable platter or record edge.
Frequently clean the needle tip-use a soft brush in a “back-to-front’ motion only.
If you must use a needle cleaning fluid, use very sparingly.
Gently wipe the dust cover and turntable housing with a soft cloth. Use only a small amount of mild detergent to clean the turntable and dust cover.
Never apply harsh chemicals or solvents to any part of the turntable system.

Hereby, NEW ONE S.A.S, declares that this MUSE MT-106 BT is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at www.muse- europe.com

SPECIFICATIONS

GENERAL

Power:

AC ADAPTOR: AC IN 100-240V AC, 50/60Hz
Output: DC 5V 2000mA
Output Power: 2 x 2W RMS

BLUETOOTH

Bluetooth Version: 5.0
Bluetooth: 2.402-2.48GHz
RF Output Power: 8 dBm
Working Distance: Up to 10 meters measured in open space (wall and structures may affect range of device)

Specifications and appearance are subject to change without notice

MORE INFORMATION

CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). There are no user serviceable parts inside the unit. Refer all servicing to qualify personnel.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of “dangerous voltage” inside the unit.
The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

WARNING!

TWheA RusNeI NGO apparatus in moderate climates.
The Marking plate is located on the bottom of the device.
Make sure to have a minimum distance of 5 cm around the unit for sufficient ventilation.
Ensure that the ventilation openings is not covered with items such as newspapers, tablecloths, curtains, etc.
Do not place naked flame sources, such as lighted candles on the apparatus.
Do not expose this appliance to dripping or splashing water.
Do not place objects filled with liquids, such as glass, vase on the device.
The power plug is used as a disconnect device and must be easily accessible. To be completely disconnected from the power, the plug of the appliance should be disconnected completely. The socket must not be obstructed and should be easily accessible during intended use.
Under the influence of fast transient and / or electrostatic electric phenomenon, the product may malfunction and the user must perform a power reset of the device.
The normal function of the product may be disturbed by strong Electro-Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location.

If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.(Waste Electrical and Electronic Equipment Directive)