Westinghouse 63296 Indoor Pendant LED Light Instruction Manual

: June 6, 2024
: Westinghouse

Table of Contents

Westinghouse 63296 Indoor Pendant LED Light
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR A
MOUNTING AND WIRING INSTRUCTIONS
CLEANING AND CARE
TECHNICAL CHARACTERISTICS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Westinghouse 63296 Indoor Pendant LED Light

ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to the place of purchase.

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit
www.westinghouselighting.eu/contact-us and www.westinghouselighting.de/contact- us

NOTE: Carefully unpack fixtures and parts. Make sure all parts are included before discarding any packing materials.

THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR A

LIST OF COMPATIBLE DIMMERS

Brand	Model #	DIMMING RANGE
BUSCH-JAEGER	6523 U-102, 2250 U	****

10 – 100%

KOPP| 8085, 8050
GIRA| 0300 00/ I01
MERTEN| EMG5131-0000

Dimmer is not included. Not recommended for use with motion sensors, light sensors, timers, or any other external controls.

Westinghouse 63296 Indoor Pendant LED Light-Fig1

MOUNTING AND WIRING INSTRUCTIONS

Thread mounting screws (A) into mounting bar (B). Secure the mounting screws (A) with hex nuts (C).
Place the mounting bar flush against the ceiling at the desired mounting location. Using outside mounting bar holes as a guide, mark where pilot holes are to be drilled.
Inset two plastic anchors (D) into the pilot holes (for drywall ceiling).
Align outside mounting bar holes with plastic anchors (D) (If applicable). Secure mounting bar (B) into place using wood screws (E).

I need to adjust the length of the fixture, please process below:

Loosen screws (F) attaching LED driver (K) (white box with wires) to the bracket (I) beneath it. Remove one screw (G) but leave the other loosely attached. Rotate the LED driver (K) carefully away from the cord to allow the cord to slide freely.
Loosen the screw in Strain Relief (J) until the cord slides easily, being careful not to completely remove the screw. Slide cord up into canopy (H) until the fixture is the correct distance below the canopy
Carefully coil the excess wire in the canopy (H), being careful not to allow the wire to knot or create tight bends (kinks).
Tighten the screw in the Strain Relief (J) until the cord does not slide, being careful not to overtighten. Slide cord through one side of cord lock (S) until cord lock (S) is nearly touching the top of the strain relief. Slide the cord through the other side of the cord lock (S) until it locks in place.
Rotate the LED driver (K) back to its original position making sure that the screw aligns with the proper hole. Tighten both screws attaching LED driver (K) to bracket (I).
Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the live [L] to the live terminal and neutral to the neutral terminal.
Tighten terminal screws. Make sure there are no stray wires.
Raise canopy (H) to ceil, allowing mounting screw (A) to protrude through openings in the canopy (H) and secure into place with cap nuts (T).

CLEANING AND CARE

To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of the fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.

Meaning of crossed-out wheeled dustbin

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.