HAMRON 016561 Portable Fuel Tank Instruction Manual

Item no: 016561

PORTABLE FUEL TANK

OPERATING INSTRUCTIONS
Important! Read the user instructions carefully before use. Save them for future reference.
(Translation of the original instructions).

SAFETY INSTRUCTIONS

WARNING!

Petrol — highly flammable.

Petrol and the fumes from petrol can easily be ignited, even at a distance, by sparks, filaments, or similar sources of heat, and can burn explosively.

• Keep naked flames, sparking equipment, electric radiators, ovens, grills, and other sources of heat at a safe distance from the product and all handling of fuel.
• Do not smoke and make sure that no one nearby is smoking when using the product or when handling fuel.
• Keep the product out of the reach of children.
• Do not put or store the product in a vehicle or in accommodation.
• Store the product in a well-ventilated area, protected from direct sunlight.
• The product is only intended for outdoor
• Keep the air screw on the tank closed when the product is not in use. Otherwise, harmful fuel fumes can flow out.
• Seek medical attention immediately after swallowing fuel. Do not induce vomiting.
• Do not breathe through the mouth.
• The product is not intended for competition fuel.
• Do not overfill.
• Put the product on the ground when filling — do not put it on the vehicle platform, inside the cab, or in the baggage
• The ball valves on the tank and hose should be closed when the product is not in use.

SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded products in accordance with local regulations.

TECHNICAL DATA

DESCRIPTION

FIG. 1

1. Filler cap
2. Airscrew
3. Hose hanger
4. Pump handle
5. Outlet nozzle

FIG. 2

6. Ball valve (closed)
7. Hose ball valve (closed)

USE

FILLING OF PRODUCT TANK
WARNING!

Read the warning label for the fuel dispenser pump.
Do not smoke and do not use a naked flame, mobile phone, or other electronic equipment when filling the product tank.

1. Place the product horizontally.
2. Make sure that the ball valve on the tank is closed.
3. Take off the filler cap.
4. Fill up with fuel. Do not overfill.
5. Replace the filler cap and check that the air screw on the cap is closed.

Do not put the product on a loading platform, in a cab or baggage compartment, on a boat deck or space under a deck, or in any other type of craft.

Fill the tank slowly to reduce the risk of spilling fuel and to minimize electrostatic charging.

LIFTING INSTRUCTIONS

NOTE:

The product should always be lifted by two persons — never attempt to lift the product by yourself.

1. Place the product horizontally.
2. Grip the handle on the top end of the product and let the helper grip the handle on the bottom of the product, and then lift together.

REFUELLING

1. Connect the hose.
   FIG. 3

2. Open the ball valves on the tank and hose.
   FIG.4

3. Open the air screw on the filler cap.

4. Lift or place the product higher than the fuel tank to be filled.

WARNING!

At least two people are needed to lift the product.
The fuel runs out by gravity and the product must therefore be placed higher than the fuel tank to be filled from the product.

5. Pump with the pump handle to get the fuel to flow.
6. Release the pump handle to stop the flow of fuel and finish the filling.
7. Close the air screw and the two ball
8. Hang up the hose on the hose hanger.
9. Close the air screw on the filler cap.

IMPORTANT:

The air screw in the filler cap on the tank should be closed when the product is not in use to avoid releasing fuel fumes.

10. Disconnect the hose to transport the
11. Place the product firmly secured and standing upright.
12. Make sure that all connections are correctly fitted and tightened and that there is no leakage.

EMPTYING THE HOSE

1. Place the product horizontally.
2. Close both ball valves.
3. Remove the hose from its connection and open the filler cap on the tank.
4. Stick the outlet nozzle on the hose in the refilling hose in the tank.
5. Hold the hose connection and ball valve over the outlet nozzle on the hose. Open the ball valve on the hose.
6. Press the pump handle repeatedly until the hose is emptied of fuel. Close the ball valve on the hose.
7. Replace the filler cap on the tank.

Because of the shape of the tank, it can be difficult to completely empty it — some residual fuel can be left in the tank.

Jula reserves the right to make changes.
For the latest version of operating instructions, see www.jula.com

JULA AB, BOX 363, SE-532 24 SKARA
2022-0314
© Jula AB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>