CoolMusic DK35S Personal Monitor Amplifier Owner’s Manual
- June 6, 2024
- COOLMUSIC
Table of Contents
CoolMusic DK35S Personal Monitor Amplifier Owner’s Manual
DK 25S Personal Monitor Amplifier
Thank you for selecting our DK PA workstation combo in a kickback style cabinet with a reflex loaded 1 O” coaxial loudspeaker. It features two channels, a Main EQ with bass/treble controls, an built in reverb with level control, a headphone socket for private listening and a DI allowing you to connect to a PA or recording.
Before you begin playing through your amplifier, it is very important to
ensure that the & product has the proper AC line voltage supplied. You can
find the proper voltage for your amp printed next to the IEC line(power) cord
on the rear panel of the unit. Each product feature is numbered. Refer to the
front panel diagram in this manual to locate the particular features next to
their number..
Please read this guide carefully to ensure your personal safety as well as the
safety of your amplifier.
FEATURES:
Channel 1: Microphone input and line input, tone, reverb, Gain controlo.
Channel 2: Line in put; Gain control; Main EQ with bass/treble controls;
Main in/output: volume control; headphone output; DI output.
Add bluetooth, MP3, audio playback and other functions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
When using electric products, basic cautions should always be followed,
including the following:
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water. For example, near or in a bathtub, swimming pool, sink, wet basement, etc.
-
Clean only with a damp cloth.
-
Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.
-
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
-
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. When the provided plug does not fit into your inlet, consult an electrician for replacement of the obsolete outlet. Never break off the grounding. Write for our free booklet “Shock Hazard and Grounding”. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
-
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.
-
Only use attachments/accessories provided by the manufacturer.
-
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a Carl is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. -
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture.
-
Does not operate normally, or has been dropped. this product is to be mounted in an equipment rack, rear support should be provided.
Front panel
CHANNEL 1:
(1) Mic Input
The Mic input is designed for low impedance microphone that is balance input.
(2) Line in
The jack input is input to various instrument sound source signals such as
keyboard, electronic drum, electric bass, acoustic guitar, etc.
(3) Tone
Adjust the gain of the microphone by adjusting the knob .
(4) Reverb
This knob is used to adjust the reverb effect of the MIC input signals.
(5) Gain control
This knob is used to adjust the gain of the LINE channel input signal.
CHANNEL 2:
(6) Line in
The Line in socket designed to accept any line level signals from equipment
such as keyboard,
bass guitar,electronic kick drums ,sound modul
(7) Gain control
This gain control allow you to adjust the level of instruments to Channel 2
line in socket,
(8) Bass
Low/bass control- Rotate the control clockwise to boosted or cut the low
frequencies such as
bass guitar,kick drums,deep vocals and key below middle
(9) Treble
High/treble control – Rotate the control clockwise to boost or cut High/treble
frequencies.
(10) Volume
Control the overall sound level from amplifier.
( ) Headphone Input
This standard 1 /4″ input socket allows you to connect standard stereo
headphones to the amplifier.
Turn the volume control all the way down before using headphones. Slowly turn
up the
Volume control and find a comfortable listening level. When headphones are
connected to the amplifiers, the speaker is automatically turned off.
- Insert U disk, single click to start recording(Indicator Light red flashing).Click again to end recording and play this recording(Click again to start a new recording).
- play recording:Double-click the record button to delete the currently playing recording; Long press the record button:switch play in order/Single cycle.
Rear Panel
( ) Power Switch
PERSONAL
MONITOR AMPUFIER SERIAL NUMBER:
DESIGNED IN COLIFORNIA
ASIEMLED IN CHINA
This two-way rocker switch applies power to the unit when placed in the ON
position. A blue LED
on the front panel illuminates when power is supplied.
( ) Power inlet socket
Connect to your power source, Make sure the specified voltage is correct for
your country.
( ) DI output
This socket provides a balanced low impedance output signal from pre amplifier
taken before the
Volume but after any tone correction,used for direct injection of amplifier
signal to a mixing desk or additional power amplifier
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>