Hotpoint AH12E09D2B PTAC with Electric Heat User Guide

June 12, 2024
Hotpoint

Hotpoint AH12E09D2B PTAC with Electric Heat

Hotpoint AH12E09D2B PTAC with Electric Heat-PRODUCT

Product Information

Product Model: AH12E09D2B

Dimensions and Installation Information:

  • Wall Case Dimensions:
    • A: 30 inches
    • C: 70 inches
  • Maximum Cord Extension: 30 inches
  • Wall Opening Dimensions: Add 1/4 to A and C dimensions for all
    cut-outs. RAB80 16-1/4 Min. H x 42-1/4 Min. W

AH12 ELECTRIC HEATER 230/208 VOLT LINE CORD CONNECTED UNITS:

  • Heater Watts: 2,580 / 2,150
  • Heater BTU: 7,800 / 6,300
  • Heater Amps: 11.3 / 10.3
  • Minimum Circuit: 15 amps
  • Recommended Protective Device: 15 amp time-delay fuse or breaker

Product Usage Instructions

To install the AH12E09D2B electric heater, follow these steps:

  1. Measure and mark the wall opening according to the Wall Opening Dimensions provided in the manual.
  2. Add 1/4 inch to both the A and C dimensions for all cut-outs.
  3. Ensure that the minimum dimensions of the wall opening are 16-1/4 inches in height and 42-1/4 inches in width.
  4. Once the wall opening is prepared, place the wall case into the opening.
  5. Extend the cord up to a maximum of 30 inches to connect it to a power source.
  6. Make sure the power supply is compatible with the AH12E09D2B’s requirements of 230/208 volts.
  7. Securely fasten the wall case to the wall, ensuring it is level and stable.
  8. Refer to the electrical specifications provided to ensure proper electrical connections.
  9. Install a 15 amp time-delay fuse or breaker as the recommended protective device for the AH12E09D2B.

Once the installation is complete, you can use the AH12E09D2B electric heater according to your heating needs. Adjust the temperature settings as desired and enjoy the benefits of its heating capabilities.

Hotpoint® PTAC with Electric Heat 15 amps, 230/208 Volt
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made inaccordance with local electrical codes and regulations.
NOTE: Aluminum wiring may pose special problems – consult a qualified electrician.

GRILLE OPTIONS

• Stamped Aluminum Grille – RAG70

ELECTRICAL CONNECTION

  • 230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
  • Power cord is permanently attached on all Hotpoint chassis.

WALL CASE DIMENSIONS

RAB80 WALL SLEEVE
Heavy-gauge galvanized steel, with insulation, for quick self-assembly. A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION

Hotpoint AH12E09D2B PTAC with Electric Heat-FIG2

WALL OPENING DIMENSIONS
Add 1/4” to A and C dimensions for all cut-outs.
RAB80 16-1/4” Min. H x 42-1/4” Min. W

AH12 ELECTRIC HEATER

AH12 ELECTRIC HEATER

230/208 VOLT| LINE CORD CONNECTED UNITS
Heater Watts| 2,580 / 2,150
Heater BTU| 7,800 / 6,300
Heater Amps| 11.3 / 10.3
Min Circuit| 15
Recommended protective Device| 15 amp time-delay fuse or breaker

FEATURE AND BENEFITS

  • 9,200 / 9,000 cooling BTU
  • 11.3 EER
  • R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
  • 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
  • 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
  • Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
  • Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
  • Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
  • Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
  • Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
  • Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
  • Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals