wiDom Smart Roller Shutter V2 Instruction Manual
- June 7, 2024
- wiDom
Table of Contents
- Revision History
- Device description
- Technical Specification
- Safety information
- Electrical connections diagram
- Device Installation
- LED status indicator
- Including the device into a Z-Wave network
- Excluding the device from a Z-Wave network
- Calibration
- Favorite Positions
- Controlling the device
- Associations
- Power consumption management
- Reset to the factory settings
- Firmware Update
- Firmware Update function.
- Configurations
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
UME-0800-290118
SMART ROLLER SHUTTER
V2
UMS 2 Operating instructions
Revision History
Rev. Doc | Date | Reviser | Pag. | Description |
---|---|---|---|---|
0 | 20/11/2018 | GT | Initial version | |
1 | 23/11/2018 | GT | 5 | Calibration description |
2 | 14/01/2019 | GT | 5, 11 | Minor update calibration, parameter 22 |
3 | 20/03/2020 | GT | 7 | Minor update on association groups description |
Device description
WiDom Smart Roller Shutter is an “in-wall device”, for the multilevel control
of roller shutter motors. It can accurately control the opening and closing of
blinds, curtains, shutters, Venetian blinds as requested by the user through
local commands or remotely using computers, smartphones, tablets.
At the same time, it is completely configurable so that it can adapt to the
most varied customers’ needs while being ready for use without needing
additional configurations in order to operate.
After an initial calibration procedure, thanks to a proprietary algorithm,
WiDom Smart Roller Shutter is able to identify the exact position of the
roller shutter without using external sensors. During the operation,
continuous and automatic control of the limit switches allows maintaining the
calibration. In the absence of a power source, the system runs a self-
repositioning procedure that restores calibration.
The device is equipped with contact protection technology (Zero Crossing)
which reduces the electrical stress on the relay contacts and ensures a longer
life. The open/closed switching of the device always occurs when the
instantaneous value of voltage is 0.
It operates in any Z-Wave network with other Z-Wave/Z-Wave Plus certified
devices and controllers from any other manufacturer. As a constantly powered
node, WiDom Smart Roller Shutter will act as a repeater regardless of the
vendor in order to increase the reliability of the network.
Line | Phase connection terminal |
---|---|
Null | Neutral connection terminal |
Motor Contacts | 1) Closure |
- Aperture
Open/Close Buttons| I1) Close command
I2) Open command
Integrated Button| 1 click to enter in Learn Mode
6 clicks to reset the system to manufacturer’s settings
Technical Specification
Power supply | 110 – 230 VAC±10% 50/60 Hz |
---|---|
Maximum Load | 1200 Watt |
System temperature limitation | 105°C |
Work temperature | From -10° to 40° C |
Power consumption | < 230 mW in standby mode |
< 500 mW when the motor is moving
Radiofrequency| Check the radio frequency section
Protection system| S0 and S2 Security
Maximum distance| up to 100 m outdoor
up to 40 m indoor
Dimensions| 37x37x17 mm
Actuator element| Relay
Compliance| CE, RoHs
Electrical IP Rating| IP20
Radio Frequency
Product Code | Z-Wave Frequency |
---|---|
UMS2EU | 868.4 MHz |
UMS2BR | 919.8 MHz, 921.4 MHz |
UMS2CL | 919.8 MHz, 921.4 MHz |
UMS2CO | 908.4 MHz, 916 MHz |
UMS2IN | 865.2 MHz |
UMS2JP | 922.5 MHz, 923.9 MHz, 926.3 MHz |
UMS2RU | 869.0 MHz |
UMS2ZA | 868.4 MHz, 869.85 MHz |
UMS2TW | 922.5 MHz, 923.9 MHz, 926.3 MHz |
UMS2AE | 868.4 MHz, 869.85 MHz |
Product Code | Z-Wave Frequency |
--- | --- |
UMS2AU | 919.8 MHz |
UMS2CN | 868.4 MHz |
UMS2HK | 919.8 MHz |
UMS2IL | 916 MHz |
UMS2MY | 919.8 MHz, 921.4 MHz |
UMS2SG | 920.9 MHz, 921.7 MHz, 923.1 MHz |
UMS2KR | 920.9 MHz, 921.7 MHz, 923.1 MHz |
UMS2TH | 920.9 MHz, 921.7 MHz, 923.1 MHz |
UMS2US | 908.4 MHz |
Safety information
INFO: WiDom Smart Roller Shutter is designed to be installed in flush
mounting junction boxes and close to the motor to be controlled.
WARNING: WiDom Smart Roller Shutter must be installed by electricians
qualified to intervene on electrical systems in compliance with safety
requirements set out by the regulations in force.
DANGER : WiDom Smart Roller Shutter must be connected with a voltage of
230 VAC, before carrying out any operation, please make sure the power main
switch is in OFF position.
DANGER: Any procedure requiring the use of the Integrated Button is
related only to the installation phase and is to be considered a service
procedure that must be performed by qualified personnel. This operation must
be performed with all necessary precautions for operating in areas with a
single level of insulation.
WARNING: Do not connect loads that exceed the maximum load allowed by the
relay contacts.
WARNING: All connections must be performed according to the electrical
diagrams provided
WARNING: WiDom Smart Roller Shutter must be installed in norm-compliant
systems suitably protected from overloads and short circuits.
Electrical connections diagram
N) Neutral; L) Phase; 1, 2) Motor terminals; i1, i2) Commands switch
WARNING: The power line must be opportunely protected from short-circuits and excess load due to a potential motor malfunction.
Device Installation
- Make sure the main switch is set to the OFF position
- Connect the device based on the diagrams provided above
- Turn the main switch to the ON position
- If necessary, calibrate the motor limit switches (see motor manufacturer’s manual)
- Include the device in the Z-Wave network
TIP: The antenna must not be shortened, removed or modified. To ensure maximum efficiency, it must be installed as shown. Large size metal equipment near the antenna can negatively affect reception. Each WiDom device is a node in a mesh network. If there are metal obstacles, the obstacle can often be overcome with a further triangulation node.
LED status indicator
The system includes an RGB LED that shows the device’s status during
installation:
Solid RED: the device is not included in any network
OFF: the device is already associated with a Z-Wave network
Blink GREEN: the device has sent an unsolicited Multilevel Frame to the
Lifeline group
Blink YELLOW: the device has sent an unsolicited Meter Frame to the Lifeline
group
Blink VIOLET: the device has sent a command to the association device. The
number of blinks is equal to the ID Association group
Blink BLUE: calibration
The sequence of GREEN-BLUE Learn Mode for inclusion
The sequence of RED-BLUE Learn Mode for exclusion
INFO: The Learn Mode status is activated or deactivated by a single click
on the integrated button.
TIP : To test if the electrical connections are correct, before the
inclusion of the device, while pressing times the external switch, the RGB LED
should flash green for the same amount of times. If it does not, check the
wire connections.
Including the device into a Z-Wave network
WiDom Smart Roller Shutter is compatible with all Z-Wave/Z-Wave Plus certified
controllers. The device supports both the Network Wide Inclusion mechanism
(which offers the ability to be included in a network, even if the device is
not directly connected to the controller) and Normal Inclusion. By default,
the inclusion procedure starts in Normal Inclusion mode and after a short
timeout, the procedure continues in Network Wide Inclusion mode that lasts for
about 20 seconds. If you are using the wisdom Multi-Sensor Room Controller
you can include the device in the preferred room by clicking on the +
button
and opening the inclusion interface.
Before including the device the LED status indicator is solid RED. The procedure of inclusion is activated by clicking Add in the inclusion interface and by pressing any sequence of clicks on the integrated button. As soon as the inclusion procedure initiates the LED indicator starts a sequence of GREEN-BLUE blinks. The device is included in the network when the LED status is OFF and the interview is completed.
Excluding the device from a Z-Wave network
Only a controller can remove the device from the network. After activating the
exclusion function by the controller, the device can be removed by setting it
in Learning Mode.
If you are using the wisdom Multi-Sensor Room Controller, the procedure of
exclusion can be activated by removing a node from the Z-Wave network and any
click sequence on the integrated button; as soon as the exclusion initiates,
the LED indicator starts a sequence of RED-BLUE blinks. The device is excluded
from the network when the LED status indicator is solid RED and the App_status
in the interface is OK.
Calibration
The calibration is the procedure through which the system carries out a
mapping of the positions taken by the roller shutter and the motor functioning
parameters. The calibration procedure runs automatically at the first startup
as soon as the device receives a command by the external switches (or by the
controller if the device is included in a Z-wave network before the execution
of the calibration procedure).
After this procedure is executed, it will be possible to control the shutter
movement.
The calibration can be activated again by using Parameter No. 20.
The system precision depends on several factors such as the motor type, the
limit switches sensitivity, the shutter type, etc. Statistically, the maximum
error occurring while reaching a set position, starting from top or from the
bottom is lower than the height of a single shutter batten.
The start of the calibration procedure requires the system to completely run
twice, from being completely closed to completely open and to stop then in the
final position.
Favorite Positions
The system can set two favorite positions: one for the upward movements (opening movements) Favorite level for ON position, the other for the downward movements (closing movements) Favorite level for OFF position. These positions can be activated by the user through a single/double click (Parameter No.1) on the UP button or on the DOWN button respectively. The levels of favorite positions can be configured using parameters No. 2 and No. 3 (see Configuration section).
Controlling the device
With wisdom devices, the normal switches/buttons found in a traditional
electrical system can become intelligent control systems.
Controlling the WiDom Smart Roller Shutter by External switches
The clicks/hold on the external switches controls the shutter movements. WiDom
framework recognizes the number of clicks or hold event on the external switch
and can be configured to perform different actions based on the identified
event.
External switch: Double command button: UP/DOWN, open/close, ON/OFF
Events: The actions performed on the external Switch: Clicks or Hold.
Click: A click means pressing the button and then releasing it.
Hold: Applies only to buttons that are normally open and occurs when the
pressure on the button lasts longer than a click.
Device status: ON/OFF/STOP, Open/Close/Stop refers to the fact that the
motor is rotating towards the direction Open/Close or it is stopped.
Control Actions
- Holding the UP/DOWN button makes the motor move in the relevant direction and stops it as soon as the button is released or the shutter reaches its limit switch.
- An action ordering a UP/DOWN movement while the motor is moving in the opposite direction will stop the motor.
- An action ordering a UP/DOWN movement while the motor is moving in the same direction will be ignored.
- A single and/or a double click (Parameter No.1) on the button UP/DOWN makes the motor move until it reaches the favorite position set for the UP/DOWN position.
Controlling the WiDom Smart Roller Shutter by the controller
The wisdom Smart Roller Shutter can be controlled by any Z-Wave / Z-Wave Plus
certified controller available in the market.
In the figure below, is represented how the device will appear once included
in the WiDom Multi-Sensor Room Controller.
View of the WiDom Smart Roller Shutter control panels inside the WiDom Multi-Sensor Room Controller interface
The control panels show the status of the load in terms of opening level, instantaneous power, and energy consumption.
The Up/Down buttons in the control panel allow to Open/Close the shutter.
Using the Up/Down button while the motor is moving in the opposite direction,
will stop the motor. By moving the cursor in the scrollbar is possible to
regulate the opening level of the shutter. The device status is typically
updated in case of status change. Nevertheless, it is possible to refresh the
shown status by using the Refresh Button .
The device configuration parameters and settings can be accessed by using the
Configuration Button .
Associations
WiDom Smart Roller Shutter can control other devices like other relays or
dimmers. It also supports 4 association groups, each of which supports the
association of up to 8 devices (nodes):
1- Lifeline: Nodes belonging to this group will receive: notifications
about device reset; changes related to the shutter status and meter reports.
2- Control 1 Click: Nodes belonging to this group will be controlled by a
basic set if the external switch receives one click.
4- Control 2 Clicks: Nodes belonging to this group will be controlled by a
basic set if the external switch receives two clicks.
5- Control 3 Clicks: Nodes belonging to this group will be controlled by a
basic set if the external switch receives three clicks.
INFO: Association ensures direct transfer of control commands between
devices, and is performed without the participation of the main controller.
TIP: WiDom Smart Roller Shutter can control up to 8 devices for each
group. To avoid network delays, we recommend limiting the number of associated
devices to no more than 5 per group.
**** INFO: If you want to add the device within the first group and you are
using the wisdom Multi-Sensor Controller, the device association group can be
configured as follows: 1) Click Configuration button, 2) select Association
section, 3) click the +
button to add a new device to the group or click on
the×
button to remove a device.
Power consumption management
Widom Smart Roller Shutter integrates a meter system that allows measuring
values of Power and Energy consumed by the motor. These values can be obtained
through the certified controllers that support the Meter Command Class version
2.
To monitor the consumption of the device, based on your needs, the cumulated
energy of the device can be reset. If you are using the wisdom Multi-Sensor
Controller, the Reset steps are the following: 1) Click Configuration button
of energy panel, 2) select a Setting section, and 3) click Reset Meter.
Reset to the factory settings
The device can be reset to the original factory settings using one of the
following methods:
Method 1: Remove the device from the Z-Wave network
Method 2: 6 consecutive clicks on the integrated button
****INFO: If the reset is performed while the device is still part of a
network, it notifies the other devices that it has been removed (Device Reset
Locally Notification).
Firmware Update
The system supports over-the-air firmware updates that do not require the device to be removed from its location. The firmware update can be activated from all certified controllers supporting version 2 of the
Firmware Update function.
WARNING : The system will be rebooted at the end of the firmware update procedure. It is advisable to carry out the firmware update procedure only when necessary and following careful planning of the intervention.
Configurations
Parameter No. 1: Numbers of clicks to control the local load (1 Byte)
Define which sequences of clicks control the local load.
Configuration | Result |
---|---|
0 | DISABLED |
Local Control disabled
1| ONE_CLICK
1 click control the local load
2| TWO_CLICKS
2 clicks control the local load
3 (Default value)| ONE_CLICK and TWO_CLICKS
1 click and 2 clicks control the local load
Parameter No. 2: Favorite level for ON position (1 byte).
Configuration | Result |
---|
50-100
100 (Default value)| 50-100% opening level (100% correspond to completely
open)
Parameter No. 3: Favorite level for OFF position (1 byte).
Configuration | Result |
---|
0-49
0 (Default value)| 0-49% opening level (0 correspond to completely closed)
Controlling the associated device
Defines the actions to be carried out on the associated devices in terms of
the Basic Set.
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 | OFF |
-1 | ON |
The values in the table above can be used to configure the parameters No. 4,
5, 6, 7, 8, and 9.
Parameter No. 4: value used for devices belonging to Group 2 when UP button
receive 1 Click (1 byte).
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 | OFF |
-1 (Default Value) | ON |
Parameter No. 5: value used for devices belonging to Group 2 when DOWN button receives 1 Click (1byte).
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 (Default Value) | OFF |
-1 | ON |
Parameter No. 6: value used for devices belonging to Group 3 when UP button receives 2 Clicks (1byte).
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 | OFF |
-1 (Default Value) | ON |
Parameter No. 7: value used for devices belonging to Group 3 when DOWN button receive 2 Clicks (1byte).
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 (Default Value) | OFF |
-1 | ON |
Parameter No. 8: value used for devices belonging to Group 4 when UP button receive 3 Clicks (1byte).
Configuration | Result |
---|---|
1-99 | Dimming purpose |
0 | OFF |
-1 (Default Value) | ON |
Parameter No. 9: value used for devices belonging to Group 4 when DOWN button receive 3 Clicks (1byte).
Configuration | Result |
---|---|
Jan-99 | Dimming purpose |
0 (Default Value) | OFF |
-1 | ON |
Other configuration parameters
Parameter No. 20: Calibration (1 byte).
Defines the status of the calibration procedure. By default, as soon as the
device has been included, the calibration starts in automatic mode. At the end
of the calibration, this parameter is set to 1.
Afterward, the calibration can be done again by setting this parameter to 0
(AUTO) or 2 (MANUAL) and clicking on any external button.
If the calibration is set in AUTO mode, it will be completed automatically.
If the calibration is set in MANUAL mode, a click on any external button is
necessary to carry on to the next step.
During the calibration, the LED indicator blinks repeatedly in BLUE.
Configuration | Result |
---|---|
1 | DONE |
Calibration has been done
2| TO_BE_DONE_MANUAL
Calibration to be done in manual mode
0 (Default Value)| TO_BE_DONE_AUTO
Calibration to be done in automatic mode
Parameter No. 21: Motor idle state definition (2 bytes)
Defines the level of power consumption under which the motor is considered
steady (stationary)
Configuration | Result |
---|
0-3000
1000 (Default Value)| Expressed in hundredths of Watt (ex. 3000=30 Watt)
Parameter No. 22: Limit switch recognition (1 byte)
The motor has reached the limit switch when its power consumption is lower
than PLIMIT (the power defined in parameter No. 21) for an amount of time
defined by this parameter.
Configuration | Result |
---|---|
1-127 | Expressed in tenths of seconds |
30 (Default Value) | Limit Switch ignored |
Disposing of the devices
This product bears the selective sorting symbol
for waste electrical and electronic equipment
(WEEE).
This means that this product must be handled pursuant to European Directive
2002/96/EC in order to be recycled or dismantled to minimize its impact on
the environment.
For further information, please contact your local or regional authorities.
Electronic products not included in the selective sorting process are
potentially dangerous for the environment and human health due to the presence
of hazardous substances.
Compliance with directives
WiDom devices are built in compliance with directives LVD 2006/95/EC, EMC
2004/108/CE and R&TTE WiDom shall not be held responsible for any damage
caused by these devices if they are used in a manner that is not compliant
with the instructions in this manual. WiDom reserves the right to make any
changes to the product that it considers necessary or useful without
jeopardizing its primary features.
Warranty
This warranty is provided by WiDom Srl (hereinafter “ wisdom ”) based in
Quartu S.Elena 09045 (CA), Italy (VAT number 03452490927). WiDom warrants to
the original purchaser (hereinafter “ Custome r”) that the device sold
under this agreement (hereinafter “ Device ”) is free from defects in
parts and workmanship under normal use for 12 months from the date of purchase
(“ Warranty Period ”). The original purchase invoice or sales receipt,
showing the date of purchase is the proof of the date of purchase by the
Customer. If a Device, sold by WiDom to the Customer, has manufacturing
defects or in any case of alleged lack of conformity, the Customer shall send
within thirty (30) days from the day in which he discovers such defects, a
claim form by using the web site (www.wisdom.it)
informing WiDom on the full name of the Customer, the nature of the defects
and the date in which the Devices has been purchased.
Warranty Claims received after the expiration of the Warranty Period shall not
be considered valid.
Once iDom, receives the Warranty Claim, it shall inform the Customer by
e-mail or letter, if the Warranty is applicable and the address where the
Device shall be sent in order to verify the effects (if any). Customers must
prepay shipping and transportation charges as indicated by wisdom. The Device
shall be sent by the Customer to WiDom at its own costs and expenses, by
express courier or hand-delivered, and with the original packaging, the
supplied accessories (if any), and documents proving date of purchase. WiDom
shall then inform the Customer about the defects and on its repair or
replacement (where applicable). Should wisdom not evidence defects on the
Device, the Device shall be returned to the Customer.
Should wisdom notices the defects, and this warranty is applicable, it will
remove, at its sole discretion, any defect, free of charge, by repairing any
defective components of the Device with new or regenerated components or by
replacing the Device. The Warranty Period of the replaced or repaired Device
shall not be extended. wisdom will ship the repaired or a replaced Device to
Customer freight prepaid.
wisdom will not be liable for damages to property caused by faulty devices.
wisdom will not be liable for indirect, incidental, special, consequential or
punitive damages, or for any damage, including, inter alia, loss of profits,
savings, data, loss of benefits, claims by third parties and any property
damage or personal injuries arising from or related to the use of the Device.
If the Device cannot be replaced with another of the same type (e.g. the
Device is no longer in production or no longer available for
selling in the Customer’s country), it may be replaced with a different one
having similar technical specifications to the faulty one. Such
replacement shall be considered as a total fulfillment of Widom’s obligations.
Warranty exclusion
– defects caused by normal wear of parts or especially subject to wear, such
as parts that require periodic replacement during the normal operation of the
system (e.g. Batteries);
– splits, cracks, scratches, dents, scratched or discolored surfaces and
parts, breakage of plastic parts, and in general of any other cosmetic damage;
– damages resulting from use of the system other than that provided, including
but not limited to the failure to follow instructions contained in the
operating manual;
– damages caused by accident, abuse, misuse, dirt, viruses, liquid contact,
fire, earthquake, improper or inadequate maintenance or calibration,
negligence or other external auses;
– environmental damage and/or defects caused by smoke, dust, dirt, soot, or
other external influences;
– damages caused by modifications and alterations in the functionality or
features without the written permission of wisdom;
– damages resulting from transportation or inadequate packaging when returning
the product to a WiDom or to an authorized service center;
– defects caused by force majeure events such as lightning, floods, fires,
incorrect voltage, improper ventilation;
– damages caused by malfunctioning software, computer virus attack, or by
failure to update the software as recommended by wisdom;
– damages resulting from surges in the power and/or telecommunication network,
improper connection to the grid in a manner inconsistent with the operating
manual, or from connecting other devices not recommended by wisdom;
– damages caused by operating or storing the device in extremely adverse
conditions, i.e. high humidity, dust, too low (freezing) or too high ambient
temperature;
– products whose serial number has been removed, damaged, or rendered
illegible;
– expiration of the Warranty Period.
If a defect is not covered by the Warranty, WiDom will inform the Customer
about the extra expenses for the repair or replacement.
This warranty may be subject to changes. Please check at www.
wisdom.it the newest warranty claim procedure.
This guarantee shall not exclude, limit or suspend the Customer’s rights when
the provided product is inconsistent with the purchase
agreement.
Extended warranty activation
The devices bought in the EU, entitle the end customers to a two-year
guarantee offered by the retailer (or trader) that is separate from
the above commercial guarantee offered by the manufacturer to the distributor
or reseller.
WiDom offers an extra year guarantee to the end customers in addition to the
EU guarantee. This warranty can be obtained only if the
customer completes, by using the contacts on Widom’s website, the following
two steps:
- Within fifteen (15) days from the date of purchase, send to WiDom a copy of the purchase invoice and product code;
- Promptly after installing the device, send to WiDom the conformity
certification issued by the professional who installed the device
with an indication of the serial number.
© All rights reserved. WiDom is a trademark of WiDom srl. All other brand names, product names, or trademarks belong to their respective owners. WiDom reserves the right to change product features and specifications at any time without notice and is not responsible for typographical or graphical errors that may appear in this document.
Please check at www.widom.it the newest version of this document.
Printed in Italy on low-impact recyclable paper.
UMS 2 Operating Instructions www.wido
References
- Home - WiDom | Dispositivi Z-Wave per la tua casa domotica
- Multi Sensor Room Controller -WiDom Z-Wave Hub for your smart home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>