denz C0100072 Ocular Heater User Manual

denz C0100072 Ocular Heater

Product Information

Specifications

• Supported power input: 10 – 32 VDC
• Current consumption: 12 VDC: ~0.54 A, 24 VDC: ~0.30 A, Off: 0.00 A
• Heating power: ~7 W

Device Setup

1. Attach the ocular heater to the eyepiece.
2. Connect the cable provided to the camera and the ocular heater.
3. Switch on the ocular heater. (15 minutes heat up time)
4. Set the switch to ‘HI’ for very cold conditions climate.
5. Set the switch to ‘OFF’ during long breaks to extend the camera’s battery life.

Green LED Indicator

• Illuminates: Heating up.
• Flashes: Operating temperature reached.
• Off: The switch is in the ‘OFF’ position or the internal safety circuit is activated.

Resetting the Internal Safety Circuit

1. Set the switch to ‘OFF’.
2. Check supply voltage (10 – 32 VDC).
3. Restart the ocular heater.

Accessories

• 170-300 mm open-end Lemo spiral cable (C0100136)
• 200-500 mm open-end Lemo spiral cable (C0100086)
• 270-650 mm open-end Lemo spiral cable (C0100087)

Disclaimer

1. Only use DENZ spiral cables.
2. Never use a power supply higher than 40V.
3. Mistreatment might damage both the heating element and circuit board.
4. Any violation on the disclaimer mentioned above results in void of warranty.

FAQ

• Q: Can I use a different brand of spiral cables?
  A: No, it is recommended to only use DENZ spiral cables to ensure proper compatibility and performance.

• Q: What happens if I use a power supply higher than 40V?
  A: Using a power supply higher than 40V can damage both the heating element and circuit board of the ocular heater.

• Q: How long does it take for the ocular heater to heat up?
  A: The ocular heater takes approximately 15 minutes to heat up.

• Q: When should I set the switch to ‘HI’?
  A: The ‘HI’ setting is recommended for very cold conditions climate.

• Q: Should I switch off the ocular heater during long breaks?
  A: Yes, switching off the ocular heater during long breaks helps extend the camera’s battery life.

Ocular Heater

Scope of Delivery

• Ocular heater
• Cable
• Transport case

Specifications

• Supported power input 10 – 32 VDC

• Current consumption
  12 VDC: ~0.54 A
  24 VDC: ~0.30 A
  Off: 0.00 A

• Heating power ~7 W

Device setup

1. Attach the ocular heater to the eyepiece.
2. Connect the cable provided to the camera and the ocular heater.
3. Switch on the ocular heater. (15 minutes heat up time)
4. Set the switch to ‘HI’ for very cold conditions (-18°C/-0.4°F).
5. Set the switch to ‘LO’ for normal conditions and humid climates.
6. Set the switch to ‘OFF’ during long breaks to extend the camera’s battery life.

Green LED indicator

• Illuminates Heating up.
• Flashes Operating temperature reached. Off
• The switch is in the ‘OFF’ position or the internal safety circuit is activated.

Resetting the internal safety circuit

1. Set the switch to ‘OFF’.
2. Check supply voltage (10 – 32 VDC).
3. Restart the ocular heater.

Accessories

• 170-300 mm open-end Lemo spiral cable C0100136
• 200-500 mm open-end Lemo spiral cable C0100086
• 270-650 mm open-end Lemo spiral cable C0100087

Disclaimer

1. Only use DENZ spiral cables
2. Never use a power supply higher than 40V.
3. Mistreatment might damage both the heating element and the circuit board.
4. Any violation on the disclaimer mentioned above results in a void of warranty.

www.denz-precision.com

References

• DENZ Präzisionsfertigung

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>