RISCO WL S42 Indoor Wireless Sounder Instruction Manual
- June 5, 2024
- RISCO
Table of Contents
- RISCO WL S42 Indoor Wireless Sounder
- Introduction
- Operational Functions
- Mounting the Sounder
- Communication Test
- Diagnostics
- Replacing Batteries
- Technical Information
- Ordering Information
- Standard Limited Product Warranty (“Limited Warranty”)
- Contacting RISCO Group
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RISCO WL S42 Indoor Wireless Sounder
Introduction
RISCO Group’s two-way indoor wireless sounder is designed to extend the signaling capabilities of the Risco Group’s wireless systems, within the protected area. The wireless sounder offers an easy and flexible solution for quick installation. The sounder is powered by its own batteries and communicates wirelessly with the security panel using the 868MHz or 433MHz frequency band.
Operational Functions
Alarm / Tamper Indication
Upon an alarm condition, the sounder will be activated for a period of time
defined by the system (Bell Time Out parameter). The maximum time that the
sound will be activated is 5 minutes.
Low Battery Indication
Upon a low battery condition, a trouble indication is sent to the panel. There
are 2 types of low battery indications:
- Radio low battery
- Speaker low battery
Supervision
Each sounder can be defined to be supervised by the panel. The system
generates a local trouble signal identifying the sounder which its signal is
not received during a predefined time, followed by a report to the Central
Station (if defined).
Pre Alarm Indication
When an entry time starts, the system transmits a pre-alarm signal to the
sounder. If the system is disarmed before the entry delay time expires, a
cancellation signal is sent to the sounder.
If the sounder does not receive a canceling signal within the entry delay
time, the sounder will be activated.
Sounder Testing
Once placing all batteries in place, the sounder performs a functional self
test indicated by a squawk sound. Testing the sounder can also be performed
remotely by the system keypad, or, using the remote configuration software.
Mounting the Sounder
-
Release the mounting bracket captive locking screw (Fig 1).
-
Turn the mounting bracket counterclockwise and separate it from the sounder.
-
Hold the mounting bracket against the wall (direction arrow pointing up) and mark the locations of the mounting holes (Fig. 2). Drill the desired mounting holes and insert screw anchors (if required).
NOTE:
Do not drill through the mounting bracket. -
Mount the bracket to the wall using the supplied screws.
-
Insert the supplied batteries into the battery chambers (speaker and radio) paying attention to the polarity (Fig 3).
-
Perform communication setup with the control panel (see Sounder/Receiver Communication Set up paragraph).
-
Once the communication setup is completed, mount the sounder to the mounting bracket by turning the sounder clockwise. Pay attention to the tamper switch.
-
Secure the captive locking screw.
Programming the sounder
Programming the wireless sounder consists of the following 3 steps:
- Setting communication between the receiver and the sounder
- Setting sounder parameters
- Testing the sounder
Step 1: Sounder/Receiver Communication Set up
The sounder must identify itself to the system’s receiver by writing its ID
into the System. Perform according to the following steps:
-
Set the receiver to the Write mode.
NOTE:
WisDom: Main Engineer menu: 9) Devices > 2)Sounder > 1) Allocation > Select sounder> Choose INWS1
Agility: Main Engineer menu: 2) Radio Devices > 1) Allocation > 1) RF Allocation
LightSYS (V2.40 and above): Main Engineer menu: 7) Install > 2) WL Device > 2) Allocation > 1) By RF > 4) Sounder -
Select the sounder’s ID.
-
Unpack the supplied batteries
-
Insert two speaker batteries into the batteries chamber (Fig. 3).
-
Insert three Radio batteries into the batteries chamber.
-
After a squawk is heard you have 10 seconds to press on the tamper switch for at least 3 seconds. If the sounder is successfully recognized, the system will sound a confirmation beep and the sounder will initiate a second squawk sound.
-
Repeat the process for other sounders in the system.
Step 2: Setting the Sounder Parameters
Each sounder can be defined with different sets of parameters. The following
table describes the list of parameters of the sounder.
NOTE:
For the specific programming location of each parameter refer to the system
manuals.
Adjusting the Volume
Defines the sounder sound volume for the following system modes
- Exit / Entry: The sound produced during Exit/Entry time (Default: 0)
- Alarm: The sound produced during an alarm (Default: 9)
- Squawk: The sound produced during squawk sounds (Default: 9)
The sound volume range is between 0 (silent) to 5 (maximum volume).
Muting Tamper
This feature disables a tamper alarm from the sounder and it is recommended to
be used when replacing the sounder’s batteries.
NOTES:
-
An ongoing tamper alarm will not be disabled.
-
Wisdom: This feature is controlled under the Engineer Menu (Quick key [9][2][5]). The tamper alarm will be disabled during the current installation programming period.
-
Agility: Grandmaster Code/User Menu > Activities > Advanced > Service Mode (Agility 3 only)
The tamper alarm will be disabled for the time programmed in the Mode Service timer. -
lights (V2.40 and above): Grandmaster Code/User Menu > Activities > Advanced > Service Mode The tamper alarm will be disabled for the time programmed in the Mode Service timer.
Setting Supervision Time
Specifies how often the system generates a supervision request to the sounder.
If any of the sounders does not respond to the request at least once, during
the receiver supervision time, the system will regard the accessory as lost.
NOTE:
The receiver supervision time should be higher than the sounder supervision
time in order to eliminate false lost event.
- Range: 00-255 minutes
- Default: 58 minutes
NOTE:
WisDom (Ver 4.25): Engineer menu Quick key 1) System > 2)Controls > 44) Pre
alarm Agility: Engineer menu [1][2] > Advanced > Sounder Pre alarm LightSYS
(V2.40 and above): Engineer menu 1) System > 2) Controls > 7) Device > 5)
Sounder Pre alarm.
Step 3: Testing the Sounder
Communication Test
The sounder communication test performs a communication test between the sounder receiver and the system.
To perform a communication test
-
Access to communication test option
NOTE:
WisDom: Engineer menu > 9) Devices > 2) Sounders > 3) Communication test. Agility: Engineer menu > 2) Testing > 5) Sounder > 1) Communication test. LightSYS (V2.40 and above): Installer Code/User menu: Maintenance > Wireless Test >Wireless Sounders > Comm. Test. -
The value displayed indicates the last signal received from the siren (In the WisDom it indicates the signal received during the test). A number between 00-99 indicates the strength of the communication signal between the system and the sounder.
NOTE:
For successful communication, the strength of the signal should be higher that the sounder receiver noise threshold level. WisDom: Engineer menu quick key [9][2][4], Agility: Engineer menu > 2)Testing >1)Main unit >
- Calibration). Agility: Engineer menu: 2) Testing > 1) Main unit > 1) Calibration LightSYS (V2.40 and above): Engineer menu: 7) Install > 2) WL Device > 1) RX Calibration
Diagnostics
The Diagnostics menu enables to test parameters reflecting the operation of the sounder:
-
Speaker batteries voltage: Tests the selected sounder’s speaker batteries voltage
-
Radio batteries voltage: Tests the selected sounder’s radio’s batteries voltage
-
Sounder version: Displays information regarding the sounder’s version
NOTE:
WisDom: User menu: 4) Maintenance > 7) Sounders > 1) Diagnostics Agility: Engineer menu > 2) Testing> 5) Sounder>2) Battery test > 3)Version LightSYS (V2.40 and above) Battery Test: Installer Code/User menu: Maintenance > WL Test > WL Sounders > Battery test LightSYS (V2.40 and above) Sounder Version: Installer Code/User menu: Maintenance. > Diagnostics > Sounders > Select Sounder >Version The diagnostic features can be also performed from Upload/Download software, locally or remotely. -
Sounder Calibration: Displays information regarding the noise level around the sounder.
NOTE:
WisDom: Engineer menu quick key: [9][2][4] Agility: Engineer menu: 2) Testing- Sounder > 4) Noise level > 1) View > 2) Calibrate LightSYS (V2.40 and above): Installer Code/User menu: Maintenance > Diagnostics > Sounders > Select Sounder > Calibration.
Replacing Batteries
- Before opening the sounder it is advised to silence the tamper alarm using the Tamper Mute option (see the Muting Tamper paragraph on page 6).
- Unlock the captive screw and remove the sounder from the mounting bracket by turning it counterclockwise.
- Remove the old batteries from the metal clips and replace with new ones. Pay attention to the polarity.
- Attach the sounder to the bracket and fasten the cover captive locking screw.
NOTES:
Dispose of old batteries according to your local regulations. Risk of
explosion if battery replaced by an incorrect type.
Technical Information
Ordering Information
Ordering Information
Part Number| Description
RWS42043300B| 2-Way Indoor Wireless Sounder, 433 MHz
RWS42086800B| 2-Way Indoor Wireless Sounder, 868.65 MHz
Specifications are subject to change without prior notice. Should any questions arise please contact your supplier?
RED Compliance Statement
Hereby, RISCO Group declares that this equipment is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
For the CE Declaration of Conformity please refer to our website:
www.riscogroup.com.
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO”) guarantees RISCO’s hardware products (“Products”) to be
free from defects in materials and workmanship when used and stored under
normal conditions and in accordance with the instructions for use supplied by
RISCO, for a period of (i) 24 months from the date of delivery of the Product
(the “Warranty Period”). This Limited Warranty covers the Product only within
the country where the Product was originally purchased and only covers
products purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit
of customers who purchased the Products directly from RISCO or from an
authorized distributor of RISCO. RISCO does not warrant the Product to
consumers and nothing in this Warranty obligates RISCO to accept Product
returns directly from end-users who purchased the Products for their own use
from RISCO’s customer or from any installer of RISCO or otherwise provide a
warranty or other services to any such end user directly. RISCO’s authorized
distributor or installer shall handle all interactions with its end-users in
connection with this Limited Warranty. RISCO’s authorized distributor or
installer shall make no warranties, representations, guarantees, or statements
to its end-users or other third parties that suggest that RISCO has any
warranty or service obligation to, or any contractual privy with, any
recipient of a Product. Remedies. In the event that a material defect in a
Product is discovered and reported to RISCO during the Warranty Period, RISCO
shall accept the return of the defective Product in accordance with the below
RMA procedure and, at its option, either (i) repair or have repaired the
defective Product, or (ii) provide a replacement product to the customer.
Return Material Authorization. In the event that you need to return your
product for repair or replacement, RISCO will provide you with a Return
Merchandise Authorization Number (RMA#) as well as return instructions. Do not
return your product without prior approval from RISCO. Any Product returned
without a valid, unique RMA# will be refused and returned to the sender at the
sender’s expense. The returned Product must be accompanied by a detailed
description of the defect discovered (“Defect Description”) and must otherwise
follow RISCO’s then-current RMA procedure published on RISCO’s website at
www.riscogroup.com in connection with any such return. If RISCO determines in
its reasonable discretion that any Product returned by the customer conforms
to the applicable warranty (“Non-Defective Product”), RISCO will notify the
customer of such determination and will return the applicable Product to the
customer at the customer’s expense. In addition, RISCO may propose and assess
customers for a charge for testing and examination of Non-Defective Products.
Entire Liability. The repair or replacement of Products in accordance with
this Limited Warranty shall be RISCO’s entire liability and the customer’s
sole and exclusive remedy in case a material defect in a Product is discovered
and reported as required herein. RISCO’s obligation and this Limited Warranty
are contingent upon the full payment by the customer for such Product and upon
proven weekly testing and examination of the Product functionality.
Limitations. This Limited Warranty is the only warranty made by RISCO with
respect to the Products. The warranty is not transferable to any third party.
To the maximum extent permitted by applicable law, this Limited Warranty shall
not apply and will be void if: (i) the conditions set forth above are not met
(including, but not limited to, full payment by the customer for the Product
and proven weekly testing and examination of the Product functionality); (ii)
if the Products or any part or component thereof: (a) have been subjected to
improper operation or installation; (b) have been subject to neglect, abuse,
willful damage, abnormal working conditions, failure to follow RISCO’s
instructions (whether oral or in writing); (c) have been misused, altered,
modified or repaired without RISCO’s written approval or combined with, or
installed on products, or equipment of the customer or of any third party; (d)
have been damaged by any factor beyond RISCO’s reasonable control such as, but
not limited to, power failure, electric power surges, or unsuitable third
party components and the interaction of software therewith or (e) any failure
or delay in the performance of the Product attributable to any means of
communication provided by any third party service provider, including, but not
limited to, GSM interruptions, lack of or internet outage and/or telephony
failure. BATTERIES ARE EXPLICITLY EXCLUDED FROM THE WARRANTY AND RISCO SHALL
NOT BE HELD RESPONSIBLE OR LIABLE IN RELATION THERETO, AND THE ONLY WARRANTY
APPLICABLE THERETO, IF ANY, IS THE BATTERY MANUFACTURER’S WARRANTY. RISCO does
not install or integrate the Product in the end user’s security system and is
therefore not responsible for and cannot guarantee the performance of the end
user’s security system which uses the Product or of which the Product is a
component.
This Limited Warranty applies only to products manufactured by or for RISCO. Further, this Limited Warranty does not apply to any software (including operating system) added to or provided with the Products or any third-party software, even if packaged or sold with the RISCO Product. Manufacturers, suppliers, or third parties other than RISCO may provide their own warranties, but RISCO, to the extent permitted by law and except as otherwise specifically set forth herein, provides its Products “AS IS”. Software and applications distributed or made available by RISCO in conjunction with the Product (with or without the RISCO brand), including, but not limited to system software, as well as P2P services or any other service made available by RISCO in relation to the Product, are not covered under this Limited Warranty. Refer to the Terms of Service at: https://riscocloud.com/ELAS/WebUI/UserLogin/License for details of your rights and obligations with respect to the use of such applications, software, or any service. RISCO does not represent that the Product may not be compromised or circumvented; that the Product will prevent any personal injury or property loss by burglary, robbery, fire, or otherwise, or that the Product will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce the risk of a burglary, robbery, or fire without warning, but it is not insurance or a guarantee that such will not occur or will not cause or lead to personal injury or property loss. CONSEQUENTLY, RISCO SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE A WARNING. EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS LICENSORS HEREBY DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS WITH REGARD TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS, TO THE EXTENT PERMITTED BY LAW. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, RISCO AND ITS LICENSORS DO NOT REPRESENT OR WARRANT THAT: (I) THE OPERATION OR USE OF THE PRODUCT WILL BE TIMELY, SECURE, UNINTERRUPTED OR ERROR-FREE; (ii) THAT ANY FILES, CONTENT OR INFORMATION OF ANY KIND THAT MAY BE ACCESSED THROUGH THE PRODUCT SHALL REMAIN SECURED OR NON DAMAGED. CUSTOMER ACKNOWLEDGES THAT NEITHER RISCO NOR ITS LICENSORS CONTROL THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT RISCO’S PRODUCTS, MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER PROBLEMS INHERENT IN THE USE OF SUCH MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY DELAYS, DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH PROBLEMS. RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS KNOWLEDGE, INFRINGE UPON ANY PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR OTHER INTELLECTUAL PROPERTY RIGHT IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR ANY AMOUNTS REPRESENTING LOST REVENUES OR PROFITS, PUNITIVE DAMAGES, OR FOR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF THEY WERE FORESEEABLE OR RISCO HAS BEEN INFORMED OF THEIR POTENTIAL. This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website www.riscogroup.com or as follows:
-
United Kingdom
Tel: +44-161-655-5500 technical@riscogroup.co.uk -
Italy
Tel: +39-02-66590054 support@riscogroup.it -
Spain
Tel: +34-91-490-2133 support-es@riscogroup.com -
France
Tel: +33-164-73-28-50 support-fr@riscogroup.com -
Belgium
Tel: +32-2522-7622 support-be@riscogroup.com -
USA
Tel: +305-592-3820 support@riscogroupusa.com -
China
Tel: +86-21-52-39-0066 support-cn@riscogroup.com -
Israel
Tel: +972-3-963-7777 support@riscogroup.com
All rights reserved
No part of this document may be reproduced in any form without prior written
permission from the publisher.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>