RISCO RVCM72P23 VUpoint Eyeball 4MP Varifocal PoE Network Camera User Guide
- June 5, 2024
- RISCO
Table of Contents
- RISCO RVCM72P23 VUpoint Eyeball 4MP Varifocal PoE Network Camera
- Eyeball Network Camera Components
- PoE Camera Settings
- power supply
- Product Specification
- FCC Rules
- Standard Limited Product Warranty (“Limited Warranty”)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RISCO RVCM72P23 VUpoint Eyeball 4MP Varifocal PoE Network Camera
Eyeball Network Camera Components
Note: For reset (used to return the camera settings to factory default mode), long press for 10 seconds and then the light turns off.
PoE Camera Settings
Note
This camera can be connected to RISCO Cloud only via the VUpoint NVR
Step 1
Connect one end of the network cable (LAN) to the camera Ethernet port and the
other side to your router or an NVR PoE Port. If the camera is not connected
to PoE, power it up by an appropriate
power supply
Step 2
Use the VUpoint NVR instructions to connect the camera to the NVR using “RISCO
Pro” Camera type
Product Specification
Parameter | Description |
---|---|
Image Sensor | 1/3” 4Megapixel progressive CMOS |
IR Distance | 50 m |
Focal Length | 2.8 – 12 mm |
WDR | 120 dB |
Firmware Upgrade | Via the camera’s web interface |
Power Supply | 12V DC/POE |
Power Consumption | <6.9W |
Operating Conditions | -30◦C to 60◦C (-22◦F to 140◦F)/ less than ≤ 95% |
Storage Temperature | -40◦C to 60◦C (-40◦F to 140◦F) |
Protection | IP67 |
EMC Compliance Statement:
Hereby, RISCO Group declares that this equipment is in compliance with the
essential requirements and other relevant provisions of Directive 2014/30/EU.
For the CE Declaration of Conformity please refer to our website:
www.riscogroup.com.
FCC Rules
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this equipment which are not expressly approved by
the party responsible for compliance (RISCO Group’s.) could void the user’s
authority to operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and
off, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on to a different circuit from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO”) guarantees RISCO’s hardware products (“Products”) to be
free from defects in materials and workmanship when used and stored under
normal conditions and in accordance with the instructions for use supplied by
RISCO, for a period of (i) 24 months from the date of delivery of the Product
( the “Warranty Period”). This Limited Warranty covers the Product only within
the country where the Product was originally purchased and only covers
products purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit
of customers who purchased the Products directly from RISCO or from an
authorized distributor of RISCO. RISCO does not warrant the Product to
consumers and nothing in this Warranty obligates RISCO to accept Product
returns directly from end-users who purchased the Products for their own use
from RISCO’s customer or from any installer of RISCO or otherwise provide
warranty or other services to any such end user directly. RISCO’s authorized
distributor or installer shall handle all interactions with its end-users in
connection with this Limited Warranty. RISCO’s authorized distributor or
installer shall make no warranties, representations, guarantees or statements
to its end-users or other third parties that suggest that RISCO has any
warranty or service obligation to, or any contractual privy with, any
recipient of a Product.
Remedies. In the event that a material defect in a Product is discovered and
reported to RISCO during the Warranty Period, RISCO shall accept return of the
defective Product in accordance with the below RMA procedure and, at its
option, either (i) repair or have repaired the defective Product, or (ii)
provide a replacement product to the customer.
Return Material Authorization. In the event that you need to return your
product for repair or replacement, RISCO will provide you with a Return
Merchandise Authorization Number (RMA#) as well as return instructions. Do not
return your Product without prior approval from RISCO. Any Product returned
without a valid, unique RMA# will be refused and returned to the sender at the
sender’s expense. The returned Product must be accompanied with a detailed
description of the defect discovered (“Defect Description”) and must otherwise
follow RISCO’s then-current RMA procedure published in RISCO’s website at
www.riscogroup.com in connection with any such return. If RISCO determines in
its reasonable discretion that any Product returned by customer conforms to
the applicable warranty (“Non-Defective Product”), RISCO will notify the
customer of such determination and will return the applicable Product to
customer at customer’s expense. In addition, RISCO may propose and assess
customer a charge for testing and examination of Non-Defective Product.
Entire Liability. The repair or replacement of Products in accordance with
this Limited Warranty shall be RISCO’s entire liability and customer’s sole
and exclusive remedy in case a material defect in a Product is discovered and
reported as required herein. RISCO’s obligation and this Limited Warranty are
contingent upon the full payment by customer for such Product and upon a
proven weekly testing and examination of the Product functionality.
Contacting RISCO
RISCO Group is committed to customer service and Product support. You can
contact us through our website (www.riscogroup.com) or at the following
telephone and fax numbers:
United Kingdom
Tel: +44-(0)-161-655-5500 support-uk@riscogroup.comItaly
Tel: +39-02-66590054 support-it@riscogroup.comSpain
Tel: +34-91-490-2133 support-es@riscogroup.comFrance
Tel: +33-164-73-28-50 support-fr@riscogroup.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>