blurams D10C Smart Doorbell with Wi-Fi and Remote Controller User Manual
- June 5, 2024
- blurams
Table of Contents
blurams D10C Smart Doorbell with Wi-Fi and Remote Controller
Packing list
Get to know your doorbell
Charge your doorbell battery
First, fully charge your doorbell battery. Plug Into a USB power source (self- provided) using the provided cable.
Charging: Status LED red light on and breathe. Charged: Status LED red light off.
Download blurams App
Download the App by searching “blurams” in the App Store or Google Play. Alternatively, you can open a QR scanner App and scan the blurams App QR code below to install the App.
Add your doorbell into App
Enter into the blurams App, sign up for a free blurams account and log in. Go to the home page and click the “+” icon on the top right corner, select doorbell. Please follow the instruction on the App interface to add your doorbell.
FAQs
If you encounter any troubles in product information, product installation and
use, please refer to the “Mine> Help And Feedback” in blurams app or email at
support@blurams.com.
Give us your feedback
blurams strive for a high-quality product and user experience, we’re eager to
hear your feedback or suggestions. Send your feedback through the App or email
at support@blurams.com.
Do not use the camera in the environment at coo high or too low temperature,
never expose the camera under strong sunshine or too wet environment.The
suitable temperature for the product and accessories is -10°C-50°C.When
charging, please place the camera in an environment that t,as a normal room
temperature and good ventilation. It is recommended to charge the camera In an
environment with a temperature that ranges from S”C~25″C. The adapter shall be
installed near the equipment and shall be easily accessible. The plug
considered as disconnect device of adapter. If you use a ttiird-party
charger, the recommended output voltage/current of the adaptor is 5Vdc/2A. and
the adapter st,all be CE approval type. CAUTION RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT 1YPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS. RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the device
and the human body. To maintain compliance with RF exposure requirement, use
product that maintain a 20cm distance between the device and human body.
Operating Frequency Range: 2412 MHz- 2472 MHz Max Output Power: < 20dBm
This product can be used across EU member states.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used In accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur In a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party. Responsible for compliance could void the user’s
authority to operate this equipment. (Example- use only shielded interface
cables when connecting to computer or perlpheral devices). This equipment
complies with Part 15 of ttie FCC Rules. Operation is subject to the following
two conditions: {1) This device may not cause harmful Interference, and (2)
This device must accept any Interference received, lncludlng interference that
may cause undesired operation. FCC Radiation Exposure Statement: The equipment
complies with FCC Radiation exposure limits set forth for uncontrolled
environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
FCC ID: 2ASAQ-D1 DC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>