LUTRON Caséta Wireless Outdoor Plug User Guide
- June 5, 2024
- Lutron
Table of Contents
LUTRON Caséta Wireless Outdoor Plug
Installing your outdoor plug
Decide on a suitable location
WARNING : SHOCK HAZARD. May result in serious injury or death. This device must be plugged into a GFCI protected circuit. The end of the cord must be at least 3 in (76.2 mm) above the ground.
Mount the outdoor plug (optional)
Using the mounting holes provided at the ends of the outdoor plug, and using 2
screws or other fasteners appropriate for your structure, mount the outdoor
plug to the structure. Use one mounting hole at the top and one mounting hole
at the bottom of the outdoor plug. Ensure the outdoor plug mounting location
is close enough to the outlet so the plug reaches the outlet and the end of
the cord is at least 3 in (76.2 mm) above the ground.
Add a wireless control
Connect the outdoor plug to either your Caséta system or to a Pico remote control (if desired). See the reverse side of this sheet for details on how to do this.
Plug in the load
The outdoor plug can control a variety of loads: lights, lighting transformers, and small pumps and motors. Simply plug your load into the outdoor plug. For more information, tips for using Caséta Wireless products, the complete Caséta Wireless product line, and more, please visit www.casetawireless.com/features
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Using your controls
- 15 A lighting / lighting transformers
- ½ HP motor load
- Codes
- Install in accordance with all national and local
- electrical codes.
Device Ratings
- Outdoor Plug
- PD-15OUT-BL
- 15 A lighting / lighting transformers
- ½ HP motor load
Codes
Install in accordance with all national and local electrical codes.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Troubleshooting
Using your Caséta Wireless outdoor plug
With a smartphone or tablet (Bridge required, sold separately) The Caséta Wireless outdoor plug can be controlled from a smartphone when used with the Lutron Smart Bridge. If you are using the outdoor plug with the Lutron Smart Bridge follow the instructions below.
-
1. **Download the Lutron app**- www.casetawireless.com/LutronApp
- Launch the Lutron app
* The Lutron app will walk you through setting up your devices
3. **Use the Lutron app to complete ALL remaining steps**
* ADD DEVICE
* * Pico remotes
* Dimmers
* Shades
4. **Schedule your lights**
5. **Connect while away**Without a smartphone or tablet
- (Bridge not required)
- Pairing the outdoor plug and Pico remote control
- (sold separately)
Press and hold “On / Off” button on outdoor plug
Hold for 6 seconds until the button starts blinking.
Press and hold “off” button on Pico remote
Hold for 6 seconds until lights flash 3 times.
Repeat steps to pair additional Pico remote controls.
Resetting the outdoor plug to its factory settings
Note: Returning an outdoor plug to its factory settings will remove it
from the Caséta system and unpair it from a Pico remote control.
Note: Unplug all loads from the outdoor plug prior to returning to
factory settings.
- Triple tap the On/Off button on the outdoor plug. DO NOT release the button after the third tap.
- Keep the On/Off button pressed for approximately 3 seconds until the button flashes quickly.
- Release the On/Off button and immediately triple tap it again. This time release the button after the third tap. The button will flash slowly.
- The outdoor plug has now been returned to its factory settings and can be reprogrammed into a system or paired with a Pico remote control.
References
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>