Arenti Dome1 Smart Indoor Pan Tilt WiFi Camera User Guide
- June 5, 2024
- Arenti
Table of Contents
Arenti Dome1 Smart Indoor Pan Tilt WiFi Camera
Quick start guide
- Packing list
- Product description
- Device configuratio
- Legal notice
Packing list
Product description
Notice
To reset the device, press and hold the reset button for 5seconds.
The camera beeps when the operation is complete.
-
Flashing red light (slow)
Waiting configuration -
Flashing red light (fast)
Searching WiFi network -
Fixed blue light
Camera connected to WiFi -
Flashing blue light
Access point mode
Camera configuration
- Step 1 Turn on your camera by plugging in the power adapter.
- Step 2 Connect your smartphone to the Wi-Fi network.
- Step 3 Download Arenti app from the App Store orGoogle Play depending on your device.
- Step 4 Launch Arenti app and sign up for the first use.
- Step 5 Follow the steps below to add your camera, then
follow the on-screen instructions.
Note
- If you have multiple cameras, please follow step 5 again to add devices one by one.
- To change Wi-Fi network, please restore the camera to factory settings and follow step 5 to add the camera.
For more information, please download the user manual at www.arenti.com
specifications
Sensor type | 1/2.9″ CMOS |
---|---|
Min. Brightness | Color 0.0lLux@Fl.2 |
Black and white 0.001Lux@Fl.2 | |
Resolution | 2 Mega pixels |
Lens | 4.0mm F2.0 |
Shutter | 1/25~1/100,000 per second |
Infrared | High power LED with ICR |
Infrared distance | l0meters |
Pan/Tilt | 0°-350°/-20°~90° |
Video compression | H.264 |
Bit rate | 32Kbps~2Mbps |
Max resolution | 1920 X 1080 |
Framerate | 1~25 per second |
Picture settings | Support HD/SD;support flip; |
Storage | SD card(Max 128G) |
Audio | Two-way audio |
Protocols | HTTP,DHCP,DNS,RTSP |
WiFi standard | IEEE802.1lb/g/n |
Frequency | 2.4 GHz~ 2.4835 GHz |
Bandwidth | 20140MHz |
WiFi encryption | WPA-PSK/WPA2-PSK |
Security | AES128 |
Working temperature | -20°(-55°( |
Power | DC5V,1A |
Consumption | 4.5W MAX |
Size(mm) | 59X70X1Q2 |
Model | TPA·67F050100VU01 |
--- | --- |
Input voltage | 100-240Vac |
input frequency | 50-60Hz |
Output voltage | +5Vdc |
Output current | lA |
Output power | 5W |
Efficiency | 73,62% |
No-load Consumption | <O.lW |
Support
www.arenti.com
Symbols
Direct current (DC)
Don’t throw batteries or out of order products with the household waste
(garbage). The dangerous substances that they are likely to include may harm
health or the environment. Make your retailer take back these products or use
the selective collect of garbage proposed by your city.
CE
Hereby, Arenti, declares that the radio equipment
type ‘DOME1’ is in compliance with the
Directive 2014/53/EU.
The full test of the EU declaration of conformity is available at the
following Internet address:
http://www.arenti.com For indoor use only
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Ihese limits are designed to provide reasonable protection against harmful interterence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna
installation instructions and consider removing the no- collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>