Arenti PET3T Smart Pet Treat Dispenser Camera User Manual
- May 15, 2024
- Arenti
Table of Contents
PET 3T(F)
QUICK GUIDE
Smart Pet Treat Dispenser Camera
PET3T Smart Pet Treat Dispenser Camera
Email: support@arenti.com
Phone: 1-866-999-7868, Mon-Fri 9AM-5PM (PT)
Toll free for USA&Canada, subject to charges for other regions Phone Service
Language only available in English
support@arenti.com
Packing list
Product description
Put the device on the table or the ground and press down to expel the air in the suction cup, so that the device will be fixed firmly. No matter how pets play with the device, it will not fall down.
Directions for use
1. Add food
Open the lid; add pet food into the food barrel, and the height of the food
should not exceed the MAX line; put back the lid.
- The capacity of food barrel is 0.5L.
- The recommended food diameter is 0.7 cm ~1.5 cm.
Food with a lot of powder or sticky food is not supported, as it is easy to get stuck. 2. Release food manually
- Power on the device
- Short press the “Feeding” button to release one food at a time. A serving of food is about 1~10, and the quantity will vary according to the size of the food. Generally, the horizontal projection distance of food is 0.5~1.5 meter.
- Release food on schedule (by App)
Download the App “Arenti” and add the device. Set up the feeding plan in the APP, and then the food will be automatically released regularly and quantitatively. 4. Clean up
Open the silicone plug of the cleaning hole, and then use the provided small brush to clean up.
Product configuration
Scan QR code to download and install the Arenti APP. Also, you can search
“Arenti” on App Store (iOS) or Google Play (Android).
Registration
Open the App. If you are a new user, tap to create a new account and follow
the prompts to complete account setup.
Note: Before creating a new account, please read the Privacy and Terms of
Use carefully. Pairing
Step 1
Open APP home page, Click “+” or “Add” and select icon according to actual
camera.
Note: When pairing, please put the camera and mobile phone close to the
router. If camera is not in the red slow blinking after 30 seconds of powering
on, press and hold the reset button for 5 seconds to reset, and then restart
to pair the camera with the APP.
Step 2
Power on the device. For about 30 seconds, the camera will emit start-up tone
and LED indicator will flash red slowly. and press “Next” on App.
Step 3
Reset the camera and press “Next” on App. Step 4
Select the WiFi network and input the password, and press “Next”. Make sure
that your phone has connected to a fluent and steady Wi-Fi already.
Note:
The number of bits in the SSID and passwords of the router should not exceed
31digits. Step 5
Click “Next” and use the camera to scan the QR code in the App on your mobile
phone, when the sound “dong dong dong” is heard, click “Notification tone
heard.”, and then the LED indicator will become solid blue after few seconds.
If no device is found and the pairing process is not successful, please check
below instructions:
- Wi-Fi password entered is correct and the same Wi-Fi network is used on the mobile device.
- Camera is in pairing mode.
- Check your WiFi for network activity.
If none of the solutions works or you have any other problems,please call
1-866-999-7868 (Mon-Fri 9AM-5PM (PT), toll free for USA&Canada, subject to
charges for other regions, Phone Service Language only available in English)
or contact support@arenti.com to get help.
Notice
If you have multiple cameras, please follow steps again to add devices one
by one.
To change Wi-Fi network, please restore the camera to factory settings and
follow steps to add the camera.
Pairing via QR code on device (exclusively for PETCAM1F)
Open APP home page, click “+” >> “Scan Code”, then scan the QR code pasted on
the device casing with the APP of your phone, and add the camera to the APP.
Pairing via Bluetooth (exclusively for PETCAM1 F)
Turn on your phone’s Bluetooth.
Open APP home page, Click “+” or “Add”, the device will be searched for by
bluetooth and appears on the page. Click the device and follow the notes to
pair the camera with APP. Settings
1. Live viewing & settings
In the live viewing interface, press ” “to enter setting interfaces and set up
the device common functions. 2 . Treat tossing
Rotate the Pan to find a suitable angle, press and release the food bowl icon
on the App to throw the food once. 3 . Recording & playing sound
In the live viewing interface, press “One-press Calling” to play the sound to
amuse the pet. You can also press “Voice Setting” in the live to select
sound.In the Voice Setting interface, you can press” “to record sounds you
like. 4. Feeding settings
In the Feeding Settings interface, press “Timed Feeding Settings” to set up
feeding time and times.
Specification
Product name | PETCAM1T | PETCAM1F |
---|---|---|
Resolution | 2048 x 1536 | 2616 x 1958 |
Angle of view | 140° | |
IR Distance | Up to 10m | |
Working temp | -20°C to 50°C | |
Local storage | Micro SD card (up to 256GB) | |
Capacity | 0.5L | |
Recommended food diameter | 0.7-1.5cm | |
Feeding distance | Horizontal 0.5-1.5m | |
Feeding direction | Pan: 0°-355° | |
Power input | DC 5V, 2A | |
Consumption | Up to 8.5W | |
Supported phone OS | iOS 9 / Android 5.0 and above version | |
2.4 GHz Wi-Fi | 2412-2472 MHz (Max. power<20dBm ) | |
5 GHz Wi-Fi | 5150-5700 MHz (Max. power<23dBm ) |
5745-5825 MHz(Max. power<30dBm )
Legal notice
Support www.arenti.com
Symbols Direct current (DC)
Don’t throw batteries or out of order products with the household waste
(garbage). The dangerous substances that they are likely to include may harm
health or the environment. Make your retailer take back the products or use
selective collect of garbage proposed by your city.
**** Hereby, we declares that the radio equipment type ‘PETCAM1T(F)’ is in
compliance with the Directive 2014/53/EU
The full test of the EU declaration of conformity is available at the
following Internet address: www.arenti.com
Restrictions declaration in the 5 GHz band
The device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the ntenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna
installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Safety Information
Power Adapter Safety:
- The power plug is intended to serve as a disconnect device.Do not drop or cause an impact to the power adapter.
- If the power cable is damaged (for example, the cord is exposed or broken), or the plug loosens,stop using it at once. Continued use may lead to electric shocks, short circuits, or fire.
- Do not touch the device or the power adapter with wet hands. Doing so may lead to short circuits, malfunctions, or electric shocks.
Child’s safety
- Comply with all precautions with regard to child’s safety. Letting children play with the device or its accessories may be dangerous.
- The device and its accessories are not intended for use by children. Children should only use the device with adult supervision.
Operation safety
- Use the device under allowed humidity and temperature conditions.
- Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it,to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.
- Observe local laws and regulations, and respect the privacy and legal rights of others.
Restrictions declaration in the 5 GHz band:
(i)the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems
Industry Canada (ISED) Compliance Statement
This device complies with Industry Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
© 2024. All rights reserved. All trade names are registered trademarks of
respective companies Apple, the Apple logo, iPhone are trademarks of Apple
Inc. registered in the U.S. and other countries. Google, the Google logo,
Android are trademarks of Google Inc. App Store is a service mark of Apple
Inc. Google Play is a service mark of Google Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>