Arenti OP1 Smart Outdoor Pan and Tilt Camera User Guide

June 1, 2024
Arenti

OP1 Smart Outdoor Pan and Tilt Camera

OP1

Smart Outdoor Pan&Tilt Camera

QUICK GUIDE

support@arenti.com

Quick start guide

  1. Packing list
  2. Product description
  3. Installation
  4. Product configuration
  5. Specification
  6. Legal notice

1. Packing list

2. Product description

1. Microphone
2. Speaker (back)
3. LED indicator
4. White light
5. IR light
6. Micro USB
7. Reset
8. SD card slot

support@arenti.com

Notice
To reset the device, press and hold the reset button
for 5s. The camera beeps when the operation is
completed.

LED indicator of camera:

Flashing red light (slow) Wait for network config
Flashing red light (fast) Connecting the network
Fixed red light Camera is malfunctional
Fixed blue light Camera network is normal

3. Installation

Wall Mounting

1. Take camera power cable through the bracket.
2/3. Install expansion screws and mounting screws.
4. Insert the camera into the bracket and point the
camera black arrow at the bracket Unlock logo.
5. Rotate the camera until it snaps into the bracket
with the black arrow pointing at the Lock logo.

Cell Mounting

1. Take camera power cable through the bracket.
2/3. Install expansion screws and mounting screws.
4. Insert the camera into the bracket and point the
camera black arrow at the bracket Unlock logo.
5. Rotate the camera until it snaps into the bracket
with the black arrow pointing at the Lock logo.

4. Product configuration

Scan QR code to download and install the Arenti APP.
You can also search “Arenti” on App Store (IOS) or Play
Store (Android).

Registration
Open the App. If you are a new user, tap to create a
account and follow the prompts to complete setup.
Note: You must agree with the Privacy Agreement.

Pairing

Open APP home page, Click “+” or “Add” and select
icon according to actual camera.
Power on the device. For about 30 seconds, camera
will emit start-up tone and LED indicator will flash
red slowly.
N ote: When pairing, please put the camera and mobile
phone close to the router. If camera is not in the red slow
blinking after 30 seconds of powering on, press and hold the
reset button for 5 seconds to reset, and then configure the
network again.

support@arenti.com

Select the Wi-Fi network and input the password,
and then click “Next”. Make sure that phone has
connected to a fluent and steady Wi-Fi already.
Scan the QR code in your phone with the camera
and click “Next”, when the camera comes out “dong
dong dong” and LED indicator becomes solid blue.

If no device is found and the pairing process is not
successful, please check below instructions:

  1. Wi-Fi network is 2.4GHz/5GHz.

  2. Wi-Fi password entered is correct and the same
    Wi-Fi network is used on the mobile device.

  3. Camera is in pairing mode.

  4. Check your WiFi for network activity.

Notice

If you have multiple cameras, please follow steps
again to add one by one. To change Wi-Fi network,
please restore the camera to factory settings and
add again.

5. Specification

Product name OP1
Resolution 2560 x 1440
Angle of view 95°
IR Distance Up to 10m
Pan/Tilt

0°~355° (Pan); 0°~90° (Tilt)

Working temp| -20°C to 50°C
Local storage|

Micro SD card (up to 128GB)

Power| DC 5V, 1A
Consumption| Up to 2.5W
Supported phone OS|

iOS 9/Android 5.0 and above version

Wireless connection|

IEEE802.11 a/b/g/n (2.4GHz&5GHz)

6. Legal notice

Support www.arenti.com
Support Direct current (DC)

Don’t throw batteries or out of order products
with the household waste (garbage). The
dangerous substances that they are likely to
include may harm health or the environment.
Make your retailer take back the products or
use selective collect of garbage proposed by
your city.
Hereby, we declares that the radio equipment
type ‘OP1’ is in compliance with the Directive
2014/53/EU
The full test of the EU declaration of conformity
is available at the following Internet address:
www.arenti.com

support@arenti.com

FCC Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be
provide with antenna installation instructions and consider removing the
no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Caution!
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

© 2023. All rights reserved. All trade names are registered trademarks of
respective companies Apple, the Apple logo, iPhone are trademarks of
Apple Inc. registered in the U.S. and other countries. Google, the Google
logo, Android are trademarks of Google Inc. App Store is a service mark
of Apple Inc. Google Play is a service mark of Google Inc.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals