Scosche UQ3 Stuckup Universal Qi Gen 3 Dash/Vent Mount Instruction Manual
- June 5, 2024
- Scosche
Table of Contents
Scosche UQ3 Stuck-up Universal Qi Gen 3 Dash/Vent Mount
INCLUDED ELEMENTS
- A. Universal Wireless Charging Mount
- B. T-Notch/Ball Adapter
- C Dash Mount
- D. Vent Mount
- E. Car Adapter
- F. Cable Routing Clips (2)
- G. Cleaning Wipe
DEVICE SETUP
- SECTION A-Universal Charging Phone Mount Overview
- SECTIO~J B -Dash h似mt Assembly & Installation
- SECTION C-Vent Mount Assembly & Installation
- SECTION D -Mount Adjustment
- SECTION E – Connection & Charging
SECTION A
Universal Wireless Charging Phone Mount
- A. Side Suppa Arms
- B. Wireless Charging Area
- C. Bottom Support
- D. Side Support Release Button
- E. T-Notch Opening
- F. Bottom Support Release Button
SECTION B
Dash Mount Assembly
- Remove the collar from the bal1-joint socket
- Place collar over ball end oft notch/ball adapter, then place ball 号’io 111 socket
- Tighten the collar onto the socket
- Placet-no:cr hitch opening
- Slide up to lock in place. Removal
- Press leve1 to release t-notch
- Slide down to remove
Installation
Clean the mounting surface using supplied wipe* Remove backing from the
adhesive base, place the mount in position, and press firmly. ‘Supplied
cleaning wipe may cause discoloration cf certain plastics. viny sand painted
surfaces It 1s recommended testing 1n an inconsp curious area.
SECTION C
Vent Mount Assembly
Insert t·notch hitch on a vent mount into the opening on the back of the mount
head (A), and slide upward (B). Slide vent mount down to remove (C)
Installation
Rotate vent clips on the mount (D) to align with(E)
Note: Works with many vent designs (F) Not compatible with curved or
circular vents (G)
SECTION D
Press the side & bottom support release buttons (A & B) to fully open the
Universal Mount
Place the device in the mount and manually press the side supports inward to
secure the device (C).
Note: The bottom suppo may also be accused rrianually to 1a1se t11e device in
the if needed Press the side support release button to remove the device.
Loosen the ball-joint collar on the Dash Mount (D) to adjust the mount angle
o「rotate mount (E).
Note: Vent mommy be •otateo only.
SECTION E
FCC Compliance Statement
Federal Communication Commission
Interference Statement This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits tor a Class B
digital device, pursuant to Part 15 of the FuC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference wll not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Ihis equipment complies with Fut radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance ot 20 Cm between the radiator and a human boay. For questions about Elgato product compliance with FCC regulations, please contact: Compliance Officer, Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA This device complies with ISED’s license-exempt RSS. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>