SCOSCHE Pl200PS InVert 200 200W Mobile Power Inverter User Manual

SCOSCHE Pl200PS InVert 200 200W Mobile Power Inverter

READ THE INSTRUCTIONS COMPLETELY BEFORE INSTALLING
WARNING: Use caution whenever removing or handling plastic parts of any vehicle. Unnecessary force or pressure can cause pieces to crack or break. FOR USE WITH 12-VOLT POWER OUTLETS ONLY. NOT FOR USE WITH CIGARETTE LIGHTER SOCKETS.

1. 200W Power Inverter
   • A. AC Outlets (3)
   • B. LED Indicators (2)
2. 12V Power Cord
   • C. Power Switch
   • D . U$8 Ports (4)

SPECIFICATIONS

• Input: 12-15VDC = 25A
• AC Output:11 OVAC, 60Hz, 200W = 1.8A
• USB Outputs 1 & 2:5VDC = 2.4A Total
• USB Outputs 3 & 4:5VDC = 2.4A Total

USING THE Pl200PS

• Preliminary: Make sure your 12V socket is in working condition. Plug the 12VDC power cable into your 12V socket.
• Use the power switch to turn on the PI200PS. The LED will illuminate green to confirm the unit is on.

LED INDICATOR (Green LED = Power On / Red LED = Power Protection Mode)

The unit will enter power protection mode in the following conditions:

• Low Input Voltage – when the input voltage drops below 10-11 VDC.
• High Input Voltage – when the input voltage exceeds 15-16VDC.
• Thermal Protection – when the internal temperature exceeds 185°F (85°C).
• Overload Protection – when a consistent load exceeds 232W or USB output current exceeds 7 .1 A.
• When the PI200PS enters power protection mode it will automatically reset once the unit’s conditions return to normal.
• For questions or concerns please contact our Tech Support at 1-800-363-4490 ext. 1

SAFETY PRECAUTIONS

• Warning: The output of this device is 11 OVAC, the same as a typical wall outlet.
• We recommend the following precautions when using this device to prevent personal injury.
• Do not insert foreign objects into the AC outlet or ventilation openings in the inverter.
• Do not place the power inverter near any flammable materials, fumes or gasses.
• Do not open the inverter; there are no user-serviceable parts inside.
• Do not expose the inverter to moisture.
• This device is not a toy. Keep the power inverter and its parts away from children.
• Do not leave the power inverter unattended while in use.
• Always disconnect the power inverter when not in use.
• Additionally, the following guidelines will help ensure proper operation and prevent damage to the inverter.
• Do not block any of the ventilation openings on the Pl200PS.
• Do not place it in a glove box, console or other small enclosure with poor air circulation.
• Do not place the inverter on or near heating vents or any equipment that generates heat.
• Avoid exposure to heat from direct sunlight.
• Do not use the inverter outdoors.

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio technician for help.

CANADIAN COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class [B) digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (8)/NMB-3(8)
For complete warranty details, please visit us at www.scosche.com or call 800-363-4490

References

• Scosche Tech Accessories | #1 Mount Brand in US & Canada
• Product registration | Register your purchase

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>