SCOSCHE 142UQ3DVSP StuckUp Charging Phone Mount Wireless Qi charger User Manual
- October 30, 2023
- Scosche
Table of Contents
SCOSCHE 142UQ3DVSP StuckUp Charging Phone Mount Wireless Qi charger
INCLUDED ELEMENTS
A. Universal Wireless Charging Mount
B. T-Notch/Ball Adapter
C. Dash Mount
D. Vent Mount
E. Car Adapter
F. Cable Routing Clips (2)
G. Cleaning Wipe
Universal Wireless Charging Phone Mount
A. Side SupportArms
B. Wireless Charging Area
C. Bottom Support
D. Side Support Release Button
E. T-Notch Opening
F. Bottom Support Release Button
Dash Mount
Assembly
-
Remove collar from ball-joint socket
-
Place collar over ball end oft-notch/ball adapter, then place ball end in socket.
-
Tighten collar onto socket.
-
Place t-notch hitch 1n opening
-
SI de up to lock in place Removal
-
Press lever to release t-notch.
-
Slide down to remove
Installation
Clean the mounting surface using supplied wipe*. Remove backing from adhesive base, place mount in position and press firmly.
*Supplied cleaning wipe may cause discoloration of certain plastics, vinyls and painted surfaces. It is recommended to test in an inconspicuous area first.
Vent Mount
Assembly
Insert t-notch hitch on vent mount into opening on back of mount head (A}, and slide upward (B)
Slide vent mount down to remove (C).
Installation
Rotate vent clips on mount (D} to align with vent (E) Note: Works with
many vent designs (F). Not compatible with curved or circular vents (G}
Press the side & bottom support release buttons (A & B) to fully open the
Universal Mount.
Place the device in the mount and manually press the side supports inward to
secure the device (C) Note: The bottom support may also be adjusted
manually to raise the device in the mount, if needed.
Press the side support release button to remove the device.
Loosen the ball-joint collar on the Dash Mount (D) to adjust mount angle or rotate mount (E), Note: Vent mount may be rotated only.
Mount Adjustment
Press the side & bottom support release buttons (A & B) to fully open the
Universal Mount
Place the device in the mount and manually press the side supports inward to
secure the device (C)
Note: The bottom support may also be adjusted manually to raise the device in
the mount, if needed.
Press the side support release button to remove the device.
Loosen the ball-joint collar on the Dash Mount (D) to adjust mount angle or
rotate mount (E),
Note: Vent mount may be rotated only
Connection & Charging
FCC Compliance Statemen
This device complies with part 15 of the FCC Rules Operation is subject to the
following two conditions: (1} This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user 1s encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver 1s connected.
- Consult the dealer or an experienced radio/TV technician for help
Canadian Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Soence and Economic Development Canada’s license-exempt
RSS(s) Operation 1s subject to the following two conditions (1) this device
may not cause interference and (2) this device must accept any interference,
including interference that may cause undesired operation of the device
This Class [B] digital apparatus complies with Canadian ICES-003
CAN ICES-3 (B)/NMB-3(8)
StuckUp Vent/Dash
Scosche Industries
1550 Pacific Avenue
Oxnard, Californra 93033
Phone· 800-J6-~-t1490 x1 / ROS-486-4450 x l
www.scosche.com
(~)2022 Scosc.nr.: lnoustries
Scosche 1s a trademark of Scosche Industries Other marks or brands are the pror.1erty of their respective owners Devices and or appearance may vary.
Designed in Oxnard, California •
SI UQ3DV l /22
Please note that changes or modifications to this product not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 15cm between the radiator & body.
This equipment complies with IC exposure limits set forth for an uncontrolled
environment.
This equipment shall be installed and operated with minimum distance 10cm
between the radiator & body
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>