SCOSCHE INVERT 150 150W Power Inverter User Manual
- June 1, 2024
- Scosche
Table of Contents
INVERT 150
INCLUDED ELEMENTS
A. 150W Power Inverter
1. LED Indicators (2)
2. USB-C Port
3. USB-A Port| 4. AC Outlet
5. Power Cord Input
8. 12V Power Cord
---|---
SPECIFICATIONS
Input 12-15V 20A
AC Output 110V ~ 60Hz,
150W 14A
USB C Output 5V 3.0A max
USB-A Output 5V 2 4A max
Total Shared Output SV 3 4A max
USING THE Pi150M
Preliminary: Make sure your 12V socket is in working condition . Plug the 12VDC power plug into your 12v socket to turn on the Pi1 SOM . The LED will illuminate green to confirm the unit is on LED INDICATORS (Green LED = Power On / Red LED = Power Protection Mode) The unit will enter power protection mode in the following conditions
- Low Input Voltage – when the input voltage drops below 10-11VDC.
- High Input Voltage when the input voltage exceeds 15-16VDC.
- Thermal Protection when the internal temperature exceeds 185°F (85°c).
- Overload Protection when a consistent load exceeds 166Wor USB output current exceeds 5 6A.
IMPORTANT NOTES
- When the Pi1 SOM enters power protection mode it will automatically reset once the unit’s conditions return to normal For questions or concerns please contact our Tech Support at 1-800-363-4490 ext. 1
- The cooling fan will automatically tum on and off to keep the unit in the correct operating temperature range Normally the fan will be on for 15 seconds and off for a minute or longer depending on the power draw
TROUBLESHOOTING
Red power
protection
light is on| 1. Unplug the unit from your 12Vaccessory port Disconnect any
cables from the AC input and/or the USB inputs.
2. Plug the unit back into the 12Vaccessory port. If the red light goes off
reconnect one device at a time. If the light goes back on try to connect
another device instead Important note: Check that the maximum watt rating of
the connected AC device 1s not greater than 1 SOW. If it is, the safety
circuit will be triggered
3. If the red light does not go off when there are no connected devices, try
the inverter in another vehicle
4. If it works in another vehicle there may be a problem with your car’s
battery or charging system Please contact Scosche at
1-800-363-4490 ext. 1 for additional
troubleshooting steps
---|---
No power to the unit| 1. If your vehicle is already in accessory mode or ‘On”
and there is no power to the unit, go to step 2.
2. Connect another device to your car’s 12V input like a USB car charger.
3. If that device works correctly, unscrew the end of the Inverter’s car
socket adapter and check the fuse If it looks burned or damaged replace it
with a 25A automotive fuse. This can be found at an auto parts store.
4. If that device does not work either, you may have a blown car fuse Please
check your car’s user manual for instructions on replacing the fuse.
SAFETY PRECAUTIONS
FOR USE WITH 12V POWER OUTLETS ONLY. NOT FOR USE WITH CIGARETTE LIGHTER
SOCKETS.
Warning : The output of this device is 110VAC, the same as a typical wall
outlet. We recommend the following precautions when using this device to
prevent personal injury
- Do not insert foreign objects into the AC outlet or ventilation openings in the inverter.
- Do not place the power inverter near any flammable materials, fumes or gasses.
- Do not open the inverter; there are no user serviceable parts inside
- Do not expose the inverter to moisture.
- This device is not a toy. Keep the power inverter and its parts away from children.
- Do not leave the power inverter unattended while in use
- Always disconnect the power inverter when not in use. Additionally, the following guidelines will help ensure proper operation and prevent damage to the inverter.
- Do not block any of the ventilation openings on the Pi150M.
- Do not place in a glove box, console or other small enclosure with poor air circulation.
- Do not place the inverter on or near heating vents or any equipment that generates heat
- Avoid exposure to heat from direct sunlight.
- Do not use the inverter outdoors.
WARNING
This unit employs components that tend to produce arcs or sparks- To prevent
fire or explosion, do not install in compartments containing batteries or
flammable materials.
CAUTION
- For continued protection against risk of fire, or electric shock replace only with same type and ratings of fuse
- To prevent fire, do not cover or obstruct vcntilt1tion openings. Do not mount in 1cro clet1rancc compt1rtmcnt. Overheating may result.
- Risk of Electric Shock, metal enclosure is not bonded to ground, test before touching
For complete warranty details, please visit us at
www.scosche.com or call
800-363-4490
Register your product on line at
www.scosche.com/register
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation Warning: changes or
modifications to this product not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected .
- Consult the dealer or an experienced radio/N technician for help.
Canadian Compliance Statement
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two condition: (1) this device may not
cause interference and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES·003 CAN ICES-3
(B)/NMB-3(8)
Invert 150 How-To Vi deo …
Scosche Industries
1550 Pacific Avenue
Oxnard, California 93033
Phone· 800 363 4490 x1 / 805 486-4450 x1
www.scosche.com
©2023 Scosche Industries
Scosche 1s a trademark of Scosche Industries
Other marks or brands are the property of their respective owners.
Devices and or appearance may vary
Designed in Oxnard, California
SI Pi150M 1/23
References
- Scosche Tech Accessories | #1 Mount Brand in US & Canada
- Product registration | Register your purchase
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>