wiiyii G1 GPS Speed Meter Instruction Manual
- June 5, 2024
- WiiYii
Table of Contents
GPS Speed meter: G1
Warning: This product’s working voltage is 5V, and it is forbidden to use a voltage higher than 5V for a power supply.
Display functions
- Satellite icon: After the satellite is found, the GPS light stops flashing and stays on for normal use.
- Vehicle speed display
- Compass: N (North) E (East) W (West) S (South)
- Speed unit: KM/H (kilometers) MPH (miles)
Wave button function
- Short press in: confirm the option after entering the setting menu.
- long press in: entering the setting, after adjusting, press vertically for 2 seconds to save and exit.
- Push left: move options after entering the setting.
- Long push left: push left for 2 seconds to turn off the buzzer alarm, do it again to turn it on.
- Push right: switch between concise mode and standard mode, move option after entering the setting.
Enter setting mode
Long press in to enter into the setting mode, press right to choose the menu, and short press in to confirm. Once finishing the setting, long press into the exit.
menu
| Function Parameters| Adjustment
range| Explanation| Default
value|
Set parameter value
interface
---|---|---|---|---|---
| speed| 50-150| Adjust the parameter value when there is an error between
HUD and dashboard.
Ex: dashboard displays 100 KM/H, HUD displays 105 KM/H. Please adjust the
parameter value to 102. (107-5)| 107|
| Over speed alarm| 30-250| When the vehicle speed reaches 150, HUD will give
the alarm| 150|
| Fatigue driving alarm| 1.0-8.0| HUD will give a fatigue driving alarm each 4
hours| 4.0|
| Brightness adjustment| 0-11| 0=automatic sensitivity adjustment
1-11=manual adjustment 1=darkest, 11=brightest 1411 is increasing
| 0|
| Speed unit| 0-1| 0=KM/H (kilometers) 1=MPH (miles)| 0|
| Factory reset| 0-1| default=0,
41, long press in for 3 seconds to save and exit| 0|
Troubleshooting
-
The screen without any display, and no power
Check whether the USB cable is damaged, replace the USB cable for testing, and prohibit the use of voltage higher than 5V for the power supply -
Without car Speed
After HUD power-on, the satellite icon flashes will start to find the satellite. Please drive the car to the road. It will work after it stops flashing -
Inaccurate Speed
A. the First check whether the speed unit is correct or not, the speed unit includes KM/H and MPH, please refer to the setting to switch the unit.
b.The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The international standard is based on satellite data. (if the dashboard shows 100, and the device shows the 105, change the default value to 102) -
Driving direction display error
After the vehicle speed exceeds 5KM / H, the direction can be displayed normally. -
Speed is still displayed after the car stops
Under the underground parking lot, tunnel, and under the overpass, there will be unstable satellite drift when there is obstruction. -
Turn off the buzzer
Push left for 2 seconds to turn off the buzzer, do it again to turn it on.
Selling point:
Applicable to all models, easy to install, plug and play
Function:
Functions: speed, compass, number of satellites, single mileage, speeding
alarm, fatigue reminder in time, automatic light sensing, kilometer switching
parameter:
Function: speed, mileage per trip, the direction of travel
Alarm: Speeding alarm, fatigue driving reminding alarm
Language selection: Chinese Simplified Chinese Traditional English
Display size: 2.1. Inch
Display: white light, green light
Weight: 158g
Product size: 61.7×63.8×47.1 mm
Remarks: Our speed display is GPS/Beidou display, so it can be used
normally under the condition of a satellite link. Generally, it can’t be
displayed in the tunnel. Places with dense floors are also affected.
In the starting phase and acceleration phase, there will be an error of 1-2KM,
which is very OK during normal driving
1X host
1XUSB line
1X Anti-slip mat
1X manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>