wiiyii P13 Head Up Display Car HUD Instructions

June 12, 2024
WiiYii

wiiyii P13 Head Up Display Car HUD Instructions
wiiyii P13 Head Up Display Car HUD

(This product Design Patent and Display Images Copyright had been registered with customs record) Thanks for purchasing our OBD smart digital device.This product connects car OBD2 interface by OBD cable, and display the driving datas, e.g. vehicle speed, engine RPM, water temperature, fuel consumption,voltage etc. It can keep the driver’s eyes always on road to avoid the dangerous of lowering down head to read the dashboard. Thisproduct won’t change any car ECU datas.

Kindly Attention

OBD2 mode working voltage: 11V ~ 18Vdc (12Vdc / 200mA)

For cars higher than 24V, please use USB cable to switch GPS system

System selection: Select the language and system after power-on, dial the right dial to select OBDr GPS system, and enter the last selected system automatically after 5 seconds without operation

Button and port functions

Product Overawe

  1. Setting button:it can push left / right, short / long press in
  2. Suction cup mount place
  3. Alternate port
  4. Light sensor: Sensing external light intensity and automatically adjusting brightness tosui the environment
  5. OBD cable and USB cable interface

Setting button/wave button function

Button Function

  1. Short press in (quick press in the button and release within 1 second):
  2. to switch the display mode
  3. to choose menu after entering the setup menu
  4. Long press in(press in the button more than 2 seconds and release):
  5. to enter the setting menu
  6. to save and exit after setting
  7. Pull left:
  8. to switch the functions in the left area
  9. to change the setting options
  10. Pull right:
  11. to switch the functions in the right area
  12. to change the setting options

Below are the functions abbreviations

ECT – Engine Coolant Temperature VLT – Voltage FUE – Fuel Consumption
RPM – Revolutions Per Minute TIM – Local time MIN-Driving time
DIS – Driving Distance MAP – Intake Pressure OIT – Oil Temperature
A/F – Air-fuel Ratio TCP – Turbine Pressure PSI – Turbine Pressure
RTC – Real-Time Clock ALS -Altitude DIR-driving direction
TPS -Throttle IAT – intake temperature ELD engine load
GPS -GPS satellite numbers

Setting Mode(Menu mode)

Long press the button vertically for 2 seconds to enter the setting item, dial down the button to select the menu, short vertical press to confirm, after adjustment, long press vertically for 2 seconds to save and exit
Setting Mode

Language Set: Please choose your familiar language ( EN-English / CN- Simplified Chinese/TW Traditional Chinese)
Sound Switch: turn on/off the buzzer
Speed Alarm: the default value is 150 (the default value can be changed,pull downistodecrease,pull up is to increase, adjust range is 5-200km/h)
Coolant alarm: default value is 120°, it means this device will give alarm when Coolant temperatureis over 120°(adjust range is 50-200)
RPM alarm : default value is 6000 r, it means this device will give alarmwhen RPMover 6000r(adjust range is 1000-8000)
BAT Alarm: default value is 10.5V, it means this device will give alarm when battery voltage is lower than\ 10.5V(adjust range is 10.0-15.0V)
Speed Adjust: adjust the speed according to the dashboard,default value is 107%(if the speed is different with the dashboard,then can adjust the value. For example, if the dashboard speed is 100Km/h, and the device speed is 105KM/h, then please adjust the value to 102)
Speed Offset: When the vehicle turns off,but the device speed is not 0, then adjust thedeviceSpeed Offset value (if the device speed shows 5KM/H, then change the device Speed Offset defaultvalue at 6)
BAT Adjust: if the battery voltage is different with the vehicle,it can be adjusted. (if the device voltage is 0.2V higher than the dashboard’s,please change the value to 98%)
Engine Size: if the fuel consumption is much different with the dashboard,please changeit asda

Displacement size(for example, if the vehicle displacement is 3.6L, please change the default value to 3.6L)

Fuel adjust: default value is 100%,it can be adjusted when the fuel consumption is different withthe dashboard. (for example, if the device fuel consumption is 0.2L higher than the dashboard, pleaseadjustitto98%)

Change Color 1: the speed color in the main display interface
Change Color 2: the left side functions color on the screen
Change Color 3: the right side functions color on the screen
Brightness: default 0(Automatic sensitivity),1-8(the brightness will be increased as the digital added)

CWT Unit : default coolant temperature is °C,also can be changed to ℉Speed unit: KM/h or MPH can be changed
Sum distance: can make the total driving distance same as dashboard(if the dashboard shows the sum distance is 30010Km,the user can make the device value at 30010 KM)
Power off time: default power off time is 10s,for Auto start and stop cars,please make the power off time to 5-300s
Sleep Voltage: default is off ,if the device can’t auto off,please adjust the voltage at 13.2Vor higherFactory set: short press in to do the factory set
Time adjust : default time is GMT+8(China time), can change the it to local time by pulling up/down

Driving test:
Speedup test: show the speed,distance,driving 400m takes time,driving 100m takes time
Acceleration test : kilometers acceleration refers to the seconds 0 to 100km/h,is a test of car power
Brake Test: Brake when the speed is over 100 KM/H, then it show brake distance and time

Error code set :
Scan DTCs: scan the ECU to check if there is the error code,and show the error details
Clean DTCs: switch to Clean the DTCs,short press in the button to finish the cleaning
Data Stream: Show all the vehicle data stream

Please note:
It is recommended to unplug the device if your car doesn’t been used for more than one week. OBD2

System Troubleshooting

  1. The screen without any display,and no power
    Start the car engine;check if the OBD cable line is tight;please pull down the OBD cables more time to ensure;check if product power switch turns on. If still no display ,please change another cartotest, analyze whether the car OBD diagnostic interface is good, if it is not good,please repair it and try again.

  2. Only the car voltage displays and be automatic power off after 30 second

  3. This product is only available for OBDII and EOBD cars when it is in OBD2 mode

  4. This product OBD2 mode does not support OBD I and JOBD

  5. OBD2 is a car protocol(U.S.A Cars:2003 Other regions:2007)

  6. Switch to the GPS system using the USB cable to display, within 5 seconds of power Pull right button to select the GPS system.

  7. Inaccurate Speed

  8. First check the speed unit is correct or not, the speed unit including KM/H and MPH,please refer to the setting to switch the unit.

  9. When the product is power on,long press in the button to enter into the menu option,pull right the button to choose the speed adjust,short press in the button to set the value,pull left or right to change the value.(if the dashboard shows 100,and the device shows the 105,change the default value at 102)

  10. There is an error on fuel consumption

  11. Checking your car displacement and make sure that the engine displacement of the deviceisassame as your car’s(e.g. car is 2.0L,please set parameter value to 2.0L)

  12. if the displacement is the same, you can also do a fine-tuning settings(e.g. equipment fuel ishigher than 0.2L,please set the parameter to 98%) Recommended: fine-tuning is optional sinceitisa real data from car computer

  13. The device can not auto power off
    Adjust the sleep voltage to 13.2V or 13.6V, then HUD will power off in 3 minutes. 6.Auto start- stop cars Adjust the shutdown voltage setting in the system settings to the COM mode

  14. HUD crashes in driving,or Hybrid car

  15. Adjust the shutdown voltage setting in the system settings to COM mode

  16. If it is not resolved, adjust the shutdown delay setting in the system settings to 300 seconds, and shut down after 5 minutes after the car goes out. (3)If it is not resolved, please switch to the GPS system for display. Within 5 seconds after the power is turned on, select the GPS system.

  17. Wrong operation lead to crashes

  18. Does the OBD2 interface use other OBD equipment (positioner, tire pressure monitoring, droplock, lift window folding, ELM27)

  19. Modified and retrofitted (central control navigation electronic throttle accelerator fixed speed cruise brushed computer system

  20. One-key start, keyless entry, remote start) will cause crashes, unplug other OBDdevices andusethe product directly, to restore factory settings (see the setting table for details)

  21. Press and hold the scroll wheel to enter the setup menu, right-click the scroll wheel to switch to system settings, press the scroll wheel vertically to enter the system settings, right click the scroll wheel to switch to factory settings, and press the scroll wheel vertically to confirm. (5)If you haven’t solved it, please switch to GPS system and use USB cable for display. Turn The Power and turn the dial for 5 seconds to select the GPS system.

GPS System Troubleshooting:

  1. 1.The screen without any display,and no power
    Start the car engine;check if the cable line is tight;or connect the USB to the computer tocheck

  2. Without car Speed
    After HUD power-on, the GPS will start to find the satellite. Please drive the car to the road. Itwillwork once gets more than 5 satellite signals.

  3. Cannot be turned on automatically or repeatedly extinguished during driving

  4. Please use the USB cable to insert the cigarette lighter

  5. If you use the OBD cable, change the sleep voltage to 13.0V or 12.8V

  6. If use the USB cable, make the sleep voltage off.

  7. Inaccurate time
    Enter the setting items: system time adjustment, turn the dial to the right to adjust the time zonetime, after adjusting, press the dial vertically shortly for 2 seconds to save and exit

  8. Inaccurate Speed

  9. First check the speed unit is correct or not, the speed unit including KM/H and MPH,please refer to the setting to switch the unit.

  10. The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The International standard is based on satellite data. (if the dashboard shows 100,and the device shows the 105,change the default value at 102)

  11. Driving direction display error
    After the vehicle speed exceeds 5KM / H, the direction can be displayed normally.

  12. Speed is still displayed after the car stops
    Under the underground parking lot, tunnel, under the overpass, there will be unstable satellite drift when there is obstruction. Please drive the vehicle to the empty road. The number of satellites found is more than 5 and it shows normal.

  13. The device cannot auto power off when the car is turned off

  14. If connects by OBD cable, it will auto power off in 3 minutes.

  15. If it still not powers off in 5 minutes,please change the sleep voltage to 13.5V, or use the USB cable.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals