Wiiyii P13 OBD Smart Digital Meter Instruction Manual
- June 9, 2024
- WiiYii
Table of Contents
OBD smart digital meter
Model P13
P13 OBD Smart Digital Meter
(This product Design Patent and Display Images Copyright had been registered
with customs record)
Thanks for purchasing our OBD smart digital device. This product connects car
OBD2 interface by OBD cable, and display the driving datas, e.g. vehicle
speed, engine RPM, water temperature, fuel consumption, voltage etc. It can
keep the driver’s eyes always on road to avoid the dangerous of lowering down
head to read the dashboard. This product won’t change any car ECU datas.
Kindly Attention:
OBD2 mode working voltage: 11V ~ 18Vdc (12Vdc / 200mA)
System selection: Select the language and system after power-on, dial the
right dial to select OBD or GPS system, and enter the last selected system
automatically after 5 seconds without operation
Button and port functions:
- Setting button: it can push left / right, short / long press in
- Suction cup mount place
- Alternate port
- Light sensor: Sensing external light intensity and automatically adjusting brightness to suit the environment
- OBD cable interface
Setting button/wave button function
- Short press in (quick press in the button and release within 1 second):
- to switch the display mode
- to choose menu after entering the setup menu
- Long press in(press in the button more than 2 seconds and release):
- to enter the setting menu
- to save and exit after setting
- Pull left:
- to switch the functions in the left area
- to change the setting options
- Pull right:
- to switch the functions in the right area
- to change the setting options
Below are the functions abbreviations :
ECT – Engine Coolant Temperature | VLT – Voltage | FUE – Fuel Consumption |
---|---|---|
RPM – Revolutions Per Minute | TIM – Local time | MIN-Driving time |
DIS – Driving Distance | MAP – Intake Pressure | OIT – Oil Temperature |
A/F – Air-fuel Ratio | TCP – Turbine Pressure | PSI – Turbine Pressure |
RTC – Real-Time Clock | ALS -Altitude | DIR-driving direction |
TPS -Throttle | IAT – intake temperature | ELD engine load |
GPS -GPS satellite numbers |
Setting Mode(Menu mode)
Long press the button vertically for 2 seconds to enter the setting item, dial
down the button to select the menu, short vertical press to confirm, after
adjustment, long press vertically for 2 seconds to save and exit
Language Set: Please choose your familiar language ( EN-English / CN-
Simplified Chinese/TW-Traditional Chinese)
Sound Switch: turn on/off the buzzer
Speed Alarm: the default value is 150 (the default value can be
changed,pull down is to decrease,pull up is to increase, adjust range is
5-200km/h)
Coolant alarm: default value is 120°, it means this device will give
alarm when Coolant temperature is over 120°(adjust range is 50-200)
RPM alarm: default value is 6000 r, it means this device will give alarm
when RPM over 6000 r(adjust range is 1000-8000)
BAT Alarm: default value is 10.5V, it means this device will give alarm
when battery voltage is lower than 10.5V(adjust range is 10.0-15.0V)
Speed Adjust: adjust the speed according to the dashboard, default value
is 107%(if the speed is different with the dashboard, then can adjust the
value. For example, if the dashboard speed is 100Km/h, and the device speed is
105KM/h, then please adjust the value to 102) Speed Offset: When the vehicle
turns off, but the device speed is not 0, then adjust the device Speed Offset
value (if the device speed shows 5KM/H, then change the device Speed Offset
default value at 6)
BAT Adjust: if the battery voltage is different with the vehicle, it can
be adjusted.
(if the device voltage is 0.2V higher than the dashboard’s, please change the
value to 98%)
Engine Size: if the fuel consumption is much different with the
dashboard, please change it as the Displacement size(for example, if the
vehicle displacement is 3.6L, please change the default value to 3.6L)
Fuel adjust: default value is 100%,it can be adjusted when the fuel
consumption is different with the dashboard.
(for example, if the device fuel consumption is 0.2L higher than the
dashboard, please adjust it to 98%)
Change Color 1: the speed color in the main display interface
Change Color 2: the left side functions color on the screen
Change Color 3: the right side functions color on the screen
Brightness: default 0(Automatic sensitivity),1-8(the brightness will be
increased as the digital added)
CWT Unit : default coolant temperature is °C, also can be changed to ℉
Speed unit: KM/h or MPH can be changed
Sum distance: can make the total driving distance same as dashboard(if
the dashboard shows the sum distance is 30010Km,the user can make the device
value at 30010KM)
Power off time: default power off time is 10s,for Auto start and stop
cars,please make the power off time to 5-300s
Sleep Voltage: default is off ,if the device can’t auto off,please adjust
the voltage at 13.2V or higher
Factory set: short press in to do the factory set
Time adjust : default time is GMT+8(China time), can change the it to
local time by pulling up/down.
Driving test:
Speedup test: show the speed, distance, driving 400m takes time, driving
100m takes time
Acceleration test: kilometers acceleration refers to the seconds 0 to
100km/h, is a test of car power
Brake Test: Brake when the speed is over 100 KM/H, then it show brake
distance and time
Error code set :
Scan DTCs: scan the ECU to check if there is the error code, and show the
error details
Clean DTCs: switch to Clean the DTCs, short press in the button to finish
the cleaning
Data Stream: Show all the vehicle data stream
Please note:
It is recommended to unplug the device if your car doesn’t been used for more
than one week.
OBD2 System Troubleshooting
-
The screen without any display, and no power
Start the car engine; check if the OBD cable line is tight; please pull down the OBD cables more times to ensure; check if product power switch turns on. If still no display , please change another car to test, analyze whether the car OBD diagnostic interface is good, if it is not good, please repair it and try again. -
Only the car voltage displays and be automatic power off after 30 second
-
This product is only available for OBDII and EOBD cars when it is in OBD2 mode
-
This product OBD2 mode does not support OBD I and JOBD
-
OBD2 is a car protocol(U.S.A Cars:2003 Other regions:2007)
-
Switch to the GPS system , within 5 seconds of power Pull right the button to select the GPS system.
-
Inaccurate Speed
-
First check the speed unit is correct or not, the speed unit including KM/H and MPH, please refer to the setting to switch the unit.
-
When the product is power on, long press in the button to enter into the menu option, pull right the button to choose the speed adjust, short press in the button to set the value, pull left or right to change the value.(if the dashboard shows 100, and the device shows the 105,change the default value at 102)
-
There is an error on fuel consumption
-
Checking your car displacement and make sure that the engine displacement of the device is as same as your car’s(e.g. car is 2.0L, please set parameter value to 2.0L)
-
if the displacement is the same, you can also do a fine-tuning settings(e.g. equipment fuel is higher than 0.2L, please set the parameter to 98%) Recommended: fine-tuning is optional since it is a real data from car computer
-
The device can not auto power off
Adjust the sleep voltage to 13.2V or 13.6V, then HUD will power off in 3 minutes. -
Auto start- stop cars
Adjust the shutdown voltage setting in the system settings to the COM mode -
HUD crashes in driving,or Hybrid car
-
Adjust the shutdown voltage setting in the system settings to COM mode
-
If it is not resolved, adjust the shutdown delay setting in the system settings to 300 seconds, and shut down after 5 minutes after the car goes out.
-
If it is not resolved, please switch to the GPS system for display. Within 5 seconds after the power is turned on, select the GPS system.
-
Wrong operation lead to crashes
-
Does the OBD2 interface use other OBD equipment (positioner, tire pressure monitoring, drop lock, lift window folding, ELM27)
-
Modified and retrofitted (central control navigation electronic throttle accelerator fixed speed cruise brushed computer system
-
One-key start, keyless entry, remote start) will cause crashes, unplug other OBD devices and use the product directly, to restore factory settings (see the setting table for details)
-
Press and hold the scroll wheel to enter the setup menu, right-click the scroll wheel to switch to system settings, press the scroll wheel vertically to enter the system settings, right-click the scroll wheel to switch to factory settings, and press the scroll wheel vertically to confirm.
-
If you haven’t solved it, please switch to GPS system . Turn on the power and turn the dial for 5 seconds to select the GPS system.
GPS System Troubleshooting:
-
The screen without any display, and no power
Start the car engine; check if the cable line is tight; -
Without car Speed
After HUD power-on, the GPS will start to find the satellite. Please drive the car to the road. It will work once gets more than 5 satellite signals. -
Cannot be turned on automatically or repeatedly extinguished during driving
Change the sleep voltage to 13.0V or 12.8V -
Inaccurate time
Enter the setting items: system time adjustment, turn the dial to the right to adjust the time zone
time, after adjusting, press the dial vertically shortly for 2 seconds to save and exit -
Inaccurate Speed
-
First check the speed unit is correct or not, the speed unit including KM/H and MPH, please refer to the setting to switch the unit.
-
The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The international standard is based on satellite data.
(if the dashboard shows 100,and the device shows the 105,change the default value at 102) -
Driving direction display error
After the vehicle speed exceeds 5KM / H, the direction can be displayed normally. -
Speed is still displayed after the car stops
Under the underground parking lot, tunnel, under the overpass, there will be unstable satellite drift when there is obstruction. Please drive the vehicle to the empty road. The number of satellites found is more than 5 and it shows normal. -
The device cannot auto power off when the car is turned off
-
If connects by OBD cable, it will auto power off in 3 minutes.
-
If it still not powers off in 5 minutes, please change the sleep voltage to 13.5V
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>