camry CR 7307 Standing Fan User Manual
- June 5, 2024
- camry
Table of Contents
CR 7307
User Manual
|
---|---
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240 V ~ 50 Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using children. Do not let the children play with the product. Do not let children or people who do not know the device to use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
-
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let the cord hang over the edge of a counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, and unplug the power.
-
In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
-
Protect the motor part of the unit from immersion in water.
-
Use only the original mounting hardware provided.
-
Switch on the device only after complete installation. The partially assembled and commissioned device does not ensure safe use and proper operation.
CAUTION: DO NOT TURN ON THE FAN WITHOUT FRONT AND REAR COVERS. -
Set up the fan away from curtains, curtains, or other objects that may be pulled in by the working fan.
-
Do not insert any objects into the cover of the fan. Otherwise, it may lead to personal 3 injuries or damage to the device.
DESCRIPTION OF THE DEVICE
1A. Front guard
1C. Clamping screw
1E. Rotor guard holder
1G. Fan base| 1B. Rotor blade
1D. Rearguard
1F. Telescopic tube
1H. Control panel
---|---
FAN ASSEMBLY
- Screw the fan base (1G) to the telescopic tube (1F) using the screw.
- Set the required height and tighten the fan height regulation nut.
- Screw the rotor guard holder (1E) to the telescopic tube (1F)
- Screw the rear guard (1D) to the motor housing, place the blade on the motor pin and tighten
- Place the front blade guard (1A) on the rear fan guard (1D) and lock using the fasteners.
USING THE DEVICE
- Prior to turning the device on ensuring that the speed of the rotor is set to ‘0’, then connect the power cord to the electrical socket.
- Using the control panel (1H) turn the fan on using buttons ‘1’, ‘2’, or ‘3’. After a few seconds, the fan blades will begin to rotate at the maximum speed of the selected gear.
- You can adjust the fan’s vertical angle by tilting the fan body.
CLEANING AND MAINTENANCE
-
Before cleaning the device remove the plug from the electrical socket.
-
The motor housing, telescopic fastening tube, and fan base may be cleaned using a damp cloth with a small amount of detergent.
-
To remove dust from the holes, the mesh housing may occasionally be wiped with a brush, rinsed in water, and dried well.
CAUTION: Do not allow the fan’s motor part or any buttons to get wet. -
After unscrewing the blade it may also be wiped with a damp cloth with detergent.
-
Store the fan in a dry place.
TECHNICAL DATA
| CR 7307 | diameter | power/max | supply voltage |
|---|---|---|---|
| 45 cm | 110/180W | 220-240V~50Hz |
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.