WyreStorm EX-100-H2 4K-60 4:2:0 HDR Extender with USB 2.0 User Guide
- June 5, 2024
- WyreStorm
Table of Contents
Quickstart Guide
4K/60 4:2:0 HDR Extender with
USB 2.0, Audio Passthrough & PoH
EX-100-H2
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation process.
IMPORTANT! Installation Requirements
- Visit the product page to download the latest firmware, document versions, additional documentation, and configuration tools.
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
- While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
In the Box
1x EX-100-H2 Transmitter
1x EX-100-H2 Receiver
1x 12V DC 2A Power Supply (US/UK/EU/AU)
4x Mounting Brackets with screws
2x 3-pin Terminal Blocks
1x QuickStart Guide (this document)
Basic Wiring Diagram
KEY
| HDMI| | Ethernet/HDBaseT
---|---|---|---
| Control| | Analog Audio
| Power| | USB
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and
terminated prior to making connections to the switcher. Read through this
section in its entirety before running or terminating the wires to ensure
proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on the signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
- WyreStorm recommends using pre-terminated HDMI cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
RS-232 Wiring
The EX-100-H2 uses a 3-pin RS-232 with no hardware flow control. Most control
systems and computers are DTE where pin 2 is RX, this can vary from device to
device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made. Refer to
RS-232 Mode Settings for details on setting RS-232 modes.
Audio Connections
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
- Verify that power is being supplied to the transmitter and receiver.
- Verify that the HDBaseT cable is properly terminated following the EIA568B standard.
- Verify that the output resolution of the source and display is supported by this extender.
- If transmitting 4K, verify that the HDMI cables used are 4K rated.
- Verify that all source and HDBaseT connections are not loose and are functioning properly.
No or Intermittent 3rd party Device Control
- Verify that the IR and RS-232 cables are properly terminated following the Wiring and Connections section.
- Verify that RS-232 modes are properly selected for the desired operation. Refer to RS-232 Mode Settings for details.
Troubleshooting Tips:
- WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
Warranty Information
WyreStorm Technologies LLC warrants that its products be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.
Specifications
Audio and Video
| Transmitter|
Receiver
Inputs| 1x HDMI In 19-pin type A
lx Audio In: 3.5mm (1/bin) TRS Stereo| lx HDBT In: 8-pin RJ-45 Female
lx Audio In: 3.5mm (1/bin) TRS Stereo
Outputs| lx HDBT Out: 8-pin RJ-45 Female
lx Audio Out: 3.5mm (1 /bin) TRS Stereo| 1 x HDMI Out: 19-pin type A
lx Audio Out: 3.5mm (1 /bin) TRS Stereo
Output Video Encoding| HDBaseT Class C
Encoding Data Rate| 10.2Gbps
End to End Latency| lOps (micro seconds)
Audio Formats| 2ch Analog/PCM I Multichannel: LPCM up to DTS-X and Dolby
Atmos
Video Resolutions (Max)|
Video Resolution
| HDMI| Cat6|
Cat6a/7
1920x1080p @60Hz 12bit| 7m/23ft| 70m/230ft| 100m/328ft
3840x2160p @30Hz 8bit 4:4:4| 15m/49ft| 70m/230ft| 100m/328ft
3840x2160p @30Hz 12bit 4:2:2 HDR| 5m/16ft| 70m/230ft| 100m/328ft
3840x2160p @60Hz 8bit 4:2:0 HDR| 7m/23ft| 70m/230ft| 100m/328ft
Note: WyreStorm recommends the use of shielded category cable| to minimize
signal noise and| interference.
Supported Standards| DCIIRGBIHDRIHDR101Dolby Vision up to 30Hz I HLG I
BT.20201B12100
Maximum Pixel Clock| 340MHz
Communication and Control
HDMI| HDMI I HDCP 2.2 I EDID I CEC Pass-through I DVI/D supported with
adapter (not included)
HDBaseT| HDMI I HDCP 2.2 I EDID I Line Audio I 1-way PoH (TX powers RX)
I Bidirectional RS-232 I CEC
RS-232| lx RS-232: 3-pin Phoenix (Transmitter and Receiver)
USB| lx Type B (host) I 4x Type A (device) Maximum uplink speed: 190Mbps
Power
Power Supply| 12V DC 2A
Max Power Consumption| 12W
Environmental
Operating Temperature| 32°F — 113°F (0°C — 45°C)110% — 90%, non-
condensing
Storage Temperature| -4°F to — 158°F (-20°C — +70°C) 110% — 90%. non-
condensing
Maximum BTU| 41 BTU/hr
Dimensions and Weight
Rack Units I Wall Box| < 1 U
Height| 21mm/0.83in
Width| 250mm/9.84in
Depth| 90.2mm/3.55in
Weight| 0.9kg/1.98Ibs
Regulatory
Safety and Emission| CE 1 FCC 1 RCM I EAC I RoHS
Copyright © 2021 WyreStorm Technologies
Note: WyreStorm reserves the right to change the product specification,
appearance, or dimensions of this product at any time without prior notice.
wyrestorm.com
EX-100-H2 Quickstart Guide | 210806
UK: +44 (0) 1793 230 343
ROW: 844.280.WYRE (9973)
support@wyrestorm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>